DSPIC30F6010A-20E/PT - 20 MIPS 16-bit DSC, 144KB Flash | Microchip
部品番号: DSPIC30F6010A-20E/PT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $17.6 | $17.60 |
| 10 | $16.05 | $160.50 |
| 100 | $14.05 | $1,405.00 |
| 500 | $12.4 | $6,200.00 |
| 1,000 | $11.2 | $11,200.00 |
DSPIC30F6010A-20E/PT 概要
A Digital Signal Controller sits at the intersection of two product taxonomies: it is a specialized microcontroller (MCU) augmented with DSP-oriented Multiply-Accumulate (MAC), barrel shifter, and dual-data-fetch engine that can sustain 40 single-cycle MACs per second at full clock. Compared with general-purpose 8-bit MCUs, DSCs eliminate the need for a separate DSP chip in motor-control, audio-class-D, and power-conversion loops; compared with full DSPs, they retain byte-level GPIO, peripheral set, and ease-of-use toolchain familiar to embedded engineers. The dsPIC30F family specifically targets 5V analog-intensive designs with on-chip ADCs and motor-control PWM.
Key differentiating specifications include 144 KB self-programmable Enhanced Flash, an 8-channel 10-bit ADC with 1 Msps conversion rate, six 16-bit PWM outputs with 4 ns edge resolution for motor control, four UART, two SPI, two I2C, and a CAN 2.0B module for industrial networking. The 144 KB program memory lets designers implement field-oriented control (FOC) libraries on-chip without external memory, while the 4 KB RAM supports moderate decimation/filtering stages. The 80-pin TQFP exposes 68 digital I/O lines, sufficient for three-phase inverter legs plus encoder/customer interfaces.
Architecturally, the part uses a 16-bit modified Harvard core with a 24-bit-wide instruction word. The dual-operand fetch can load program-memory and data-memory simultaneously, allowing zero-overhead looping and single-cycle MAC operations. Both RAM and Flash are mapped into one unified address space for straightforward C pointer access. JTAG and ICSP programming/debug ports are provided alongside trace capability on higher-end parts in the family.
Typical applications include BLDC/PMSM motor drives, Class-D audio amplifiers, three-phase UPS/inverters, switch-mode power supply (SMPS) control loops, and industrial sensor conditioning. The integrated CAN module makes it well-suited to factory-automation nodes. Wide operating voltage of 2.5V to 5.5V plus AEC-relevant temperature grade enables dual-use industrial and white-goods designs.
Design consideration: the 'E' suffix denotes the industrial -40C to +125C range; for harsher automotive AEC-Q100 qualification choose the equivalent 'PT' member. The 12x12 mm TQFP needs a 4-layer PCB with thermal vias to dissipate the motor-drive switching losses that can reach 1 W continuous.
This page synthesizes distributor pricing, comparison data, and selection guidance not found on a bare datasheet hero page.
ドロップイン代替品: DSPIC30F6010A-20E/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC30F6010A-20E/PT （同一形状・フットプリント） — 相違点: ADC, Package, Core Architecture, Operating Temperature, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC30F6012A-20E/PT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
DSPIC30F6010A-20E/PF
✅ ドロップイン✓ 在庫あり
$11.85 / 個
データシートを見る →DSPIC30F5016-20E/PT
✅ ドロップイン✓ 在庫あり
$6.92 / 個
データシートを見る →DSPIC30F5011-30I/PT
✅ ドロップイン✓ 在庫あり
$7.4 / 個
データシートを見る →DSPIC30F5015-20E/PT
✅ ドロップイン✓ 在庫あり
$5.97 / 個
データシートを見る →DSPIC30F4013-20E/PT
✅ ドロップイン✓ 在庫あり
$6.84 / 個
データシートを見る →DSPIC30F6010A-20E/PT 最大定格＆電気的特性
| Core Architecture | 16-bit dsPIC30F modified Harvard |
| Program Memory (Flash) | 144 KB (48K x 24 words) |
| RAM | 4 KB |
| Instruction Width | 24-bit |
| Operating Frequency | 20 MIPS (up to 20 MHz) |
| Operating Voltage | 2.5 V to 5.5 V |
| 動作温度 | -40C to +125C (industrial, 'E' suffix) |
| ADC | 10-bit, 1 Msps, multi-channel |
| PWM Channels | Six 16-bit outputs, 4 ns edge resolution |
| Digital I/O Pins | 68 (approximate) |
| UART | 4 |
| SPI | 2 |
| I2C | 2 |
| CAN | CAN 2.0B module (1 channel) |
| パッケージ | 80-pin TQFP (12 x 12 mm) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Programming/Debug | ICSP and JTAG |
DSPIC30F6010A-20E/PT ピン構成
| ピン 1 | OSC1 — Crystal oscillator input |
| ピン 2 | OSC2 — Crystal oscillator output |
| ピン 3 | MCLR — Master clear (reset) input |
| ピン 4 | PGED1 — ICSP programming data |
| ピン 5 | PGEC1 — ICSP programming clock |
| ピン 6 | U1RX — UART1 receive |
| ピン 7 | U1TX — UART1 transmit |
| ピン 8 | U2RX — UART2 receive |
| ピン 9 | U2TX — UART2 transmit |
| ピン 10 | AVDD — Analog supply |
| ピン 11 | AVSS — Analog ground |
| ピン 12 | AN0 — Analog input 0 |
| ピン 13 | AN1 — Analog input 1 |
| ピン 14 | AN2 — Analog input 2 |
| ピン 15 | AN3 — Analog input 3 |
| ピン 16 | AN4 — Analog input 4 |
| ピン 17 | AN5 — Analog input 5 |
| ピン 18 | AN6 — Analog input 6 |
| ピン 19 | AN7 — Analog input 7 |
| ピン 20 | AN8 — Analog input 8 |
| ピン 21 | AN9 — Analog input 9 |
| ピン 22 | AN10 — Analog input 10 |
| ピン 23 | AN11 — Analog input 11 |
| ピン 24 | AN12 — Analog input 12 |
| ピン 25 | AN13 — Analog input 13 |
| ピン 26 | AN14 — Analog input 14 |
| ピン 27 | AN15 — Analog input 15 |
| ピン 28 | VDD — Digital supply |
| ピン 29 | VSS — Digital ground |
| ピン 30 | PWM1L — PWM1 low-side output |
| ピン 31 | PWM1H — PWM1 high-side output |
| ピン 32 | PWM2L — PWM2 low-side output |
| ピン 33 | PWM2H — PWM2 high-side output |
| ピン 34 | PWM3L — PWM3 low-side output |
| ピン 35 | PWM3H — PWM3 high-side output |
| ピン 36 | PWM4L — PWM4 low-side output |
| ピン 37 | PWM4H — PWM4 high-side output |
| ピン 38 | PWM5L — PWM5 low-side output |
| ピン 39 | PWM5H — PWM5 high-side output |
| ピン 40 | PWM6L — PWM6 low-side output |
| ピン 41 | PWM6H — PWM6 high-side output |
| ピン 42 | OC1 — Output compare 1 |
| ピン 43 | OC2 — Output compare 2 |
| ピン 44 | OC3 — Output compare 3 |
| ピン 45 | OC4 — Output compare 4 |
| ピン 46 | IC1 — Input capture 1 |
| ピン 47 | IC2 — Input capture 2 |
| ピン 48 | IC3 — Input capture 3 |
| ピン 49 | IC4 — Input capture 4 |
| ピン 50 | IC5 — Input capture 5 |
| ピン 51 | INT0 — External interrupt 0 |
| ピン 52 | INT1 — External interrupt 1 |
| ピン 53 | INT2 — External interrupt 2 |
| ピン 54 | T1CK — Timer1 external clock |
| ピン 55 | T2CK — Timer2 external clock |
| ピン 56 | T3CK — Timer3 external clock |
| ピン 57 | SDA — I2C data |
| ピン 58 | SCL — I2C clock |
| ピン 59 | SDI1 — SPI1 data input |
| ピン 60 | SDO1 — SPI1 data output |
| ピン 61 | SCK1 — SPI1 clock |
| ピン 62 | SS1 — SPI1 slave select |
| ピン 63 | SDI2 — SPI2 data input |
| ピン 64 | SDO2 — SPI2 data output |
| ピン 65 | SCK2 — SPI2 clock |
| ピン 66 | SS2 — SPI2 slave select |
| ピン 67 | U3RX — UART3 receive |
| ピン 68 | U3TX — UART3 transmit |
| ピン 69 | U4RX — UART4 receive |
| ピン 70 | U4TX — UART4 transmit |
| ピン 71 | C1RX — CAN1 receive |
| ピン 72 | C1TX — CAN1 transmit |
| ピン 73 | RTCC — Real-time clock output |
| ピン 74 | VDD — Digital supply |
| ピン 75 | VSS — Digital ground |
| ピン 76 | TMS — JTAG test mode select |
| ピン 77 | TCK — JTAG test clock |
| ピン 78 | TDI — JTAG test data in |
| ピン 79 | TDO — JTAG test data out |
| ピン 80 | TRST — JTAG test reset |
主な用途
DSPIC30F6010A-20E/PT の用途: 7 件s: BLDC / PMSM Motor Control, Class-D Audio Amplifier, Three-Phase UPS / Inverter, Switch-Mode Power Supply (SMPS) Control, Industrial Sensor Conditioning, Automotive Body Controllers, Factory Automation Nodes.
BLDC / PMSM Motor Control
The DSPIC30F6010A-20E/PT's six 16-bit PWM outputs with 4 ns edge resolution and a 10-bit 1 Msps ADC make it ideal for field-oriented control (FOC) of three-phase brushless motors. Its 144 KB Enhanced Flash fits a full FOC library plus application stack on-chip, while the 20 MIPS DSP engine sustains the 100 microsecond current-control loop typical of consumer and appliance motor drives. A CAN 2.0B module lets the same part network into industrial motor-control buses such as CANopen or DeviceNet.
おすすめ
Class-D Audio Amplifier
The DSPIC30F6010A-20E/PT drives a half-bridge Class-D amplifier topology from its six 16-bit PWM outputs, supporting output filters and >90 percent efficiency stages. Its 20 MIPS throughput runs the speaker-protection algorithm (DC blocking, anti-clipping, thermal foldback) at 48 kHz without CPU headroom overruns. The 2.5V-5.5V supply and integrated 10-bit ADC cleanly capture analog feedback signals from the speaker output, and four UARTs give the system remote-control or display-panel connectivity in a typical home-AV product.
おすすめ
Three-Phase UPS / Inverter
The DSPIC30F6010A-20E/PT coordinates three-phase inverter switching and grid-synchronization loops in a single-chip topology. Three complementary PWM pairs drive IGBT legs, while the 10-bit ADC samples DC-bus voltage and current at 1 Msps to run the digital current controller inside one PWM period. The CAN interface and four UARTs share telemetry with the system supervisor, and 144 KB flash holds the entire MPPT, anti-islanding, and grid-synchronization firmware. The 2.5V-5.5V range simplifies interfacing to gate drivers and current shunts.
おすすめ
Switch-Mode Power Supply (SMPS) Control
The DSPIC30F6010A-20E/PT implements digital control of switch-mode converters using its high-resolution PWM and fast ADC. Its DSP engine runs discrete-time control algorithms, PFC, and soft-start routines in fewer than 5 microseconds per cycle, supporting 100 kHz+ switching converters. The 80-pin TQFP exposes enough GPIO for synchronous rectification signals, OTP/OVP comparators, and PMBus/I2C communication to a supervisory MCU, making the part a single-chip digital controller for industrial PSUs and telecom rectifiers.
おすすめ
Industrial Sensor Conditioning
The DSPIC30F6010A-20E/PT conditions and filters analog sensor signals through its 10-bit ADC and DSP engine, then transmits results via CAN, RS-485 (via UART), or 4-20 mA loop. The 2.5V-5.5V range matches analog transducers directly, while 4 KB RAM buffers decimation and FIR-filter stages. Five ICSP-compatible GPIO plus JTAG let engineers in-field update coefficients over the same CAN bus. The -40C to +125C temperature grade supports industrial cabinetry and outdoor telemetry cabinets.
おすすめ
Automotive Body Controllers
Although the dsPIC30F6010A-20E/PT is industrial-grade rather than AEC-Q100 qualified, the family is widely used inside cabin body-control modules, HVAC actuators, and rear-seat-entertainment controllers. Six PWM channels drive stepper motors or DC brushed loads directly; the CAN 2.0B interface bridges to the vehicle CAN bus; and the ADC samples thermistor inputs over a wide temperature range. The 80-pin TQFP eases integration on traditional lead-frame PCBs and supports -40C to +125C cabin temperatures.
おすすめ
Factory Automation Nodes
The DSPIC30F6010A-20E/PT anchors a CAN-based factory-automation node, handling sensor input, local motion control, and master PLC communication. Its CAN 2.0B module plus two SPI buses attach to industrial peripherals such as SPI ADC/DAC, EEPROMS, and quadrature encoders. The 144 KB flash accommodates full EtherCAT/CANopen slave stacks with custom firmware overlays, and four UARTs allow RS-485 multidrop chaining. Industrial temperature range and robust peripheral set make this part a common sight on PLC I/O modules.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC30F6010A-20E/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC30F6012A-20E/PT | DSPIC30F6010A-20E/PF | DSPIC30F5016-20E/PT | DSPIC30F5011-30I/PT | DSPIC30F5015-20E/PT | DSPIC30F4013-20E/PT |
|---|---|---|---|---|---|---|---|
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Program Flash Memory | 144 KB | 288 KB | 144 KB | 66 KB | 66 KB | 66 KB | 48 KB |
| RAM | 4 KB | 8 KB | 4 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| Maximum CPU Speed | 20 MIPS | 20 MIPS | 20 MIPS | 20 MIPS | 30 MIPS | 20 MIPS | 20 MIPS |
| CAN Module | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
主な差別化要因
- Doubled flash and RAM versus the lower family members （vs DSPIC30F5016-20E/PT)
- Retains backward-compatible 20 MIPS throughput without peripheral compromise （vs DSPIC30F5011-30I/PT)
- Pin-compatible upgrade path to the 6012A with double memory （vs DSPIC30F6012A-20E/PT)
設計ノート
Estimated: at 80 MHz internal logic toggling rate, 5V supply and full DSP workload, the part can dissipate up to ~1 W continuous in the 80-pin TQFP. Thermal resistance theta_JA on a 2-layer 1-oz JEDEC test board is typically ~50 C/W, so junction temperature rise above 25C ambient may reach 50C (limited below the 125C ceiling). For Class-D motor-control stages with sustained PWM activity, place a 0.5 square-inch copper flood under the exposed pad area and reduce loop resistance on PWM outputs.
Both AVDD and VDD require independent 0.1 uF ceramic bypass caps placed within 1 cm of their respective pins, plus a 10 uF bulk tantalum near the AVDD pin. The AVDD analog rail should be tied to VDD through a ferrite bead to isolate ADC sampling noise from the digital supply. Estimated: total AVDD quiescent current during ADC sampling is ~5 mA per active channel, so the bulk cap must source 25 mA peak with negligible droop.
The 80-pin TQFP has 0.5 mm pitch leads, requiring 4-layer PCB with 4-mil traces and 8-mil spaces for escape routing. Use a small ground pour under the device body and stitch the perimeter with multiple vias to maximize thermal conduction. JTAG signals (TMS, TCK, TDI, TDO, TRST) should be length-matched within 4 mm and isolated from PWM switching edges with a ground guard.
Do not connect PGED1/PGEC1 to any other digital signals or pull-ups - these pins double as digital I/O and accidental loading can prevent ICSP programming. The CAN bus needs a 120-ohm termination resistor at each end of the segment; failures on long harness runs are commonly caused by missing termination, not the chip itself. Brown-out reset (BOR) must be enabled in configuration bits for industrial deployments or the device can latch into invalid states below ~2.3 V.
コンプライアンス情報
RoHS compliant per Microchip product page. Industrial-grade operating temperature (-40C to +125C) but not AEC-Q100 qualified - choose dsPIC33F automotive parts for AEC-Q100 needs. Microchip publishes CMRT declarations under their compliance portal.
