EFM32TG210F16-D-QFN32 - 32MHz Cortex-M3 MCU | Silicon Labs
部品番号: EFM32TG210F16-D-QFN32 ✓ 生産中EFM32TG210F16-D-QFN32 概要
A microcontroller is a complete programmable control device integrating a processor core, Flash program memory, RAM, clocking, interrupt control, and peripherals such as timers, communications interfaces, and analog blocks. Within the product hierarchy, the EFM32TG210 belongs to the Tiny Gecko family of 32-bit microcontrollers and uses the ARM Cortex-M3 processor architecture.
Key specifications include a maximum clock frequency of 32 MHz, 16 KB of program Flash, 4 KB of SRAM, and 24 digital I/O pins. The processor can reach 1.25 Dhrystone MIPS per MHz, while an integrated Memory Protection Unit supports as many as eight memory segments. A Wake-up Interrupt Controller handles interrupts generated while the CPU is asleep.
The EFM32TG210 combines relatively high processing performance with low-power behavior suitable for battery-operated equipment. Published power characteristics include consumption as low as 0.6 uA in Stop mode and approximately 150 uA/MHz in Run mode. Autonomous peripheral operation allows timers and other functions to continue handling defined events while the processor remains in a low-energy state, reducing the need for continuous software polling.
Typical applications include connected sensor nodes, compact industrial controllers, battery-powered meters, low-power communications equipment, wearable accessories, and embedded subsystems that need a 32-bit core in a small surface-mount footprint. The 1.85 V to 3.8 V operating supply range also suits designs built around low-voltage 3 V power rails.
When laying out the board, treat the exposed pad as a thermal and electrical connection point and follow the manufacturer land-pattern and thermal-via guidance. Confirm the device pin names against the manufacturer pinout table, and place the external decoupling capacitors close to their associated supply pins to limit impedance in fast-switching current paths.
This page combines manufacturer-family specifications, same-footprint device comparisons, and practical implementation guidance to help engineers evaluate the EFM32TG210F16-D-QFN32 for compact, low-power embedded control designs.
ドロップイン代替品: EFM32TG210F16-D-QFN32 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EFM32TG210F16-D-QFN32 (同一形状・フットプリント) — 相違点: Package, Flash Memory, Digital I/O Pins, Product Type, RAM.
EFM32TG210F32-QFN32
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32TG210F8-QFN32
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32G210F128-QFN32
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32G200F32-QFN32
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32ZG210F16-QFN32
✅ ドロップイン📋 参考代替品(カタログ未掲載)
EFM32TG210F16-D-QFN32 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Series | EFM32 Tiny Gecko |
| Maximum CPU Frequency | 32 MHz |
| Core Architecture | ARM Cortex-M3, 32-bit RISC |
| Flash Memory | 16 KB |
| RAM | 4 KB |
| Digital I/O Pins | 24 |
| Timers | 2 x 16-bit |
| Supply Voltage Range | 1.85 V to 3.8 V |
| Stop Mode Current | 0.6 uA |
| Run Mode Current | 150 uA/MHz |
| Processor Performance | Up to 1.25 Dhrystone MIPS/MHz |
| Memory Protection Unit Segments | Up to 8 |
| パッケージ | 32-QFN (6 x 6 mm) |
| 実装タイプ | Surface mount |
| Program Memory Organization | 16K x 8 |
EFM32TG210F16-D-QFN32 32-qfn (6 x 6 mm) ピン配置ガイド
EFM32TG210F16-D-QFN32 (32-qfn (6 x 6 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EFM32TG210F16-D-QFN32.
詳細は データシート をご参照ください。
主な用途
EFM32TG210F16-D-QFN32 の用途: 6 件s: Battery-Powered IoT Sensor Node, Industrial Control and Monitoring Module, Low-Power Communications Terminal, Smart Metering and Utility Endpoint, Portable Medical or Wellness Device, Embedded Accessory and Wearable Controller.
Battery-Powered IoT Sensor Node
The EFM32TG210F16-D-QFN32 fits compact sensor nodes that periodically report measurements and spend most of their operating time asleep. According to the manufacturer EFM32TG210 datasheet, the device consumes as little as 0.6 uA in Stop mode, while the Cortex-M3 core reaches 32 MHz when processing is required. Its 16 KB of Flash accommodates a compact acquisition, filtering, and communications firmware, and 4 KB of RAM supports typical protocol buffers. The Wake-up Interrupt Controller allows captured events to trigger processing even when the processor is sleeping.
おすすめ
Industrial Control and Monitoring Module
The EFM32TG210F16-D-QFN32 is suitable for compact industrial modules that supervise digital equipment, read sensors, and maintain deterministic timing functions. Its two 16-bit timers support periodic sampling, input capture, and output compare tasks, while 24 digital I/O pins provide practical connectivity in a 6 x 6 mm package. The 1.85 V to 3.8 V operating range fits 3 V equipment architectures. Confirm the exact peripheral allocation and exposed-pad layout against the manufacturer pinout before committing the PCB footprint.
おすすめ
Low-Power Communications Terminal
The EFM32TG210F16-D-QFN32 can serve as the control MCU in a low-power communications terminal requiring fast peripheral handling and low standby demand. At up to 32 MHz, the Cortex-M3 core provides sufficient throughput for protocol stacks, while autonomous timers and the Wake-up Interrupt Controller reduce unnecessary main-loop activity. The 16 KB Flash limitation makes code size a primary design constraint, so use the F32 family member when libraries, dual protocol stacks, or OTA buffers no longer fit. Verify serial-interface pin multiplexing on the chosen board revision.
おすすめ
Smart Metering and Utility Endpoint
The EFM32TG210F16-D-QFN32 is a practical controller for low-cost metering endpoints that accumulate measurements and transmit compact data packets. Its 24 digital I/O pins can support pulse-output sensors, status indicators, and interface isolation components, while the low-power sleep behavior helps manage the energy budget of battery or energy-harvesting installations. The Cortex-M3 Memory Protection Unit supports up to eight protected memory segments, allowing firmware tasks to be separated. Confirm pulse-counter and wake-up timing requirements in the manufacturer application guidance.
おすすめ
Portable Medical or Wellness Device
The EFM32TG210F16-D-QFN32 can control a compact wellness wearable or portable health-accessory device that combines sensor acquisition with low-energy operation. The 24 digital I/O pins support buttons, LEDs, and sensor-control signals, while the 32 MHz Cortex-M3 core handles signal conditioning and local filtering. Its Stop-mode figure of 0.6 uA supports duty-cycled operation between measurement events. For connected medical equipment, validate regulatory requirements, isolation strategy, and the complete analog signal chain independently of the MCU selection.
おすすめ
Embedded Accessory and Wearable Controller
The EFM32TG210F16-D-QFN32 fits embedded accessory controllers where board area and standby energy are constrained. The 32-QFN 6 x 6 mm package leaves room for sensors and radio circuitry, and 24 digital I/O pins provide flexible control of LEDs, buttons, and host interfaces. The Cortex-M3 core offers a familiar 32-bit architecture while the 16 KB Flash option keeps the firmware footprint modest. For products using a companion radio or higher-bandwidth interface, validate interrupt latency, pin sharing, and firmware footprint before layout release.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EFM32TG210F16-D-QFN32 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EFM32TG210F32-QFN32 | EFM32TG210F8-QFN32 | EFM32G210F128-QFN32 | EFM32G200F32-QFN32 | EFM32ZG210F16-QFN32 |
|---|---|---|---|---|---|---|
| Package | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M0+ |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 24 MHz |
| Flash Memory | 16 KB | 32 KB | 8 KB | 128 KB | 32 KB | 16 KB |
| RAM | 4 KB | 4 KB | 2 KB | 8 KB | 8 KB | 4 KB |
| Digital I/O Pins | 24 | 24 | 24 | 24 | 24 | 24 |
主な差別化要因
- Balanced 32-bit performance and compact 16 KB Flash configuration (vs EFM32TG210F32-QFN32)
- Higher processing frequency than the Cortex-M0+ alternative (vs EFM32ZG210F16-QFN32)
- More memory than the reduced-memory Tiny Gecko option (vs EFM32TG210F8-QFN32)
- Substantially smaller Flash footprint than the G210F128 option (vs EFM32G210F128-QFN32)
設計ノート
Use the manufacturer QFN land pattern and thermal-via arrangement for the 32-QFN 6 x 6 mm package. Keep the exposed-pad connection unobstructed because it is part of the package's thermal and electrical construction. Place input and bulk decoupling capacitors near their designated supply pins, and route high-current or fast-switching signals away from the exposed pad to prevent voltage drops and added thermal stress.
Design the supply for the 1.85 V to 3.8 V operating range while allowing for startup, load transients, and the voltage drop across the power-path components. Low-power sleep performance is only realized when leakage and wake-up paths are controlled. Confirm that the regulator can start the MCU into the required operating state and that the brownout and reset design follows the manufacturer guidance.
Do not choose a same-package alternative solely from the Flash and RAM figures. The EFM32ZG210F16-QFN32 uses Cortex-M0+ at up to 24 MHz instead of Cortex-M3 at up to 32 MHz, while EFM32G-series devices may have different peripheral sets. Check pin multiplexing, interrupt vectors, timer functions, analog peripherals, driver support, and the exposed-pad layout before treating any listed alternative as a production substitute.
Assign all peripheral pins from the manufacturer pin-description table rather than inferring functions from a generic 32-QFN drawing. The EFM32TG210 provides 24 digital I/O pins, and several package pins are devoted to supplies, grounds, and the exposed pad. Assign communication lines to pins that support the required peripheral, keep sensitive analog routes short, and isolate clocks and high-speed signals from precision measurement inputs.
コンプライアンス情報
The manufacturer product listing and datasheet excerpts do not state the requested compliance attributes. Confirm current RoHS, REACH, halogen-free, and conflict-minerals declarations for the exact ordering code before production release.