EP1C3T100C8 - Cyclone FPGA 2,910 LEs TQFP-100 | Intel | EOL
部品番号: EP1C3T100C8 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.4 | $5,700.00 |
| 1,000 | $9.75 | $9,750.00 |
EP1C3T100C8 概要
A field-programmable gate array (FPGA) is a semiconductor IC containing an array of configurable logic blocks (CLBs), programmable routing, and dedicated hard IP such as block RAM, PLLs, and I/O serdes. FPGAs occupy the middle ground between fixed-function ASICs and software-driven microcontrollers: the silicon is generic, but designers define every flip-flop, LUT, and interconnect at compile time using HDL bitstreams. Within the broader taxonomy, the EP1C3T100C8 sits at FPGA & CPLD > programmable logic > semiconductor IC.
Key specifications include 13 M4K RAM blocks (4 Kbits each, plus 512 parity bits) totaling 59,904 memory bits, one general-purpose PLL for clock synthesis and phase shifting, embedded multipliers are not present on EP1C3 devices, and 65 LVDS-pair-capable or 3.3 V-tolerant user I/Os. Configuration is supported via active serial (AS), passive serial (PS), and JTAG modes, allowing the device to boot from low-cost EPCS configuration memories or be programmed in-circuit through the JTAG header.
Architecture-wise, the Cyclone I family uses 4-input look-up tables (LUT4) per logic element with a dedicated register and carry chain for arithmetic, plus per-LAB control signals. The 0.13 µm process with copper interconnect minimizes dynamic power, while the 1.5 V core VCCINT keeps static leakage low for cost-sensitive, high-volume applications. Die size and routing density are tuned for designs in the 2K-3K LE range such as glue logic, I/O expansion, custom peripherals, and protocol bridges.
Typical applications include industrial control glue logic, low-cost I/O expansion and bridging (UART/SPI/I2C to parallel), legacy peripheral replacement, motor-control co-processors, educational and prototyping boards, video/display formatting front-ends, and consumer-electronics glue functions where a small, deterministic logic device replaces discrete 74-series logic. The EP1C3T100C8 is also widely used as a firmware-controlled test fixture controller in production lines.
Designers should note that this device is EOL with last-time-buy status per Intel PDN1810; new designs are directed to Cyclone IV, Cyclone V, or Cyclone 10 families. For existing production, ensure the 1.5 V core is generated by a low-noise LDO and that JTAG chain integrity is verified before in-system programming. I/O bank VCCIO must be matched to the driven/receiving logic level (1.5 V, 1.8 V, 2.5 V, or 3.3 V) to prevent bus contention and long-term reliability issues.
This page synthesizes distributor pricing, parametric alternatives from the same Cyclone I family, and practical EOL-avoidance guidance not consolidated on any single manufacturer or distributor page.
ドロップイン代替品: EP1C3T100C8 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EP1C3T100C8 （同一形状・フットプリント） — 相違点: Package, Family, Speed Grade, Operating Temperature, Process Technology.
クイック比較ツール — 並列比較する代替部品を選択:
EP1C3T100C8N
✅ ドロップイン✓ 在庫あり
$14.2 / 個
データシートを見る →EP1C3T100I7N
✅ ドロップイン✓ 在庫あり
$13.85 / 個
データシートを見る →EP1C3T100C7
✅ ドロップイン✓ 在庫あり
$10.88 / 個
データシートを見る →EP1C3T100C7N
✅ ドロップイン✓ 在庫あり
$10.6 / 個
データシートを見る →EP1C3T100I7
✅ ドロップイン✓ 在庫あり
$15.95 / 個
データシートを見る →EP1C3T100C6
✅ ドロップイン✓ 在庫あり
$13.4 / 個
データシートを見る →EP1C3T100C6N
✅ ドロップイン✓ 在庫あり
$13.5 / 個
データシートを見る →EP1C3T100C8 最大定格＆電気的特性
| Family | Cyclone I |
| Core Process | 0.13 µm SRAM |
| Core Voltage (VCCINT) | 1.5 V |
| Logic Elements | 2,910 LEs |
| Total RAM Bits | 59,904 bits |
| M4K RAM Blocks | 13 (4 Kbit each) |
| Embedded Multipliers | Not present on EP1C3 |
| PLLs | 1 general-purpose PLL |
| Global Clock Networks | 8 |
| User I/O Pins | 65 |
| パッケージ | TQFP-100 (14x14 mm) |
| Speed Grade | -8 (commercial) |
| 動作温度 | 0C to +85C (commercial) |
| 実装タイプ | Surface Mount |
| Configuration Modes | AS, PS, JTAG |
| I/O Standards | LVTTL, LVCMOS, SSTL-2/3, LVDS, RSDS |
| RoHS ステータス | Compliant |
| Lifecycle | EOL per PDN1810 (since 2019) |
EP1C3T100C8 ピン構成
| ピン 1 | I/O — User I/O pin (bank 1) |
| ピン 2 | I/O — User I/O pin (bank 1) |
| ピン 3 | I/O — User I/O pin (bank 1) |
| ピン 4 | I/O — User I/O pin (bank 1) |
| ピン 5 | VCCIO1 — I/O bank 1 supply voltage |
| ピン 6 | I/O — User I/O pin (bank 1) |
| ピン 7 | I/O — User I/O pin (bank 1) |
| ピン 8 | I/O — User I/O pin (bank 1) |
| ピン 9 | I/O — User I/O pin (bank 1) |
| ピン 10 | I/O — User I/O pin (bank 1) |
| ピン 11 | GND — Ground |
| ピン 12 | I/O — User I/O pin (bank 2) |
| ピン 13 | I/O — User I/O pin (bank 2) |
| ピン 14 | I/O — User I/O pin (bank 2) |
| ピン 15 | I/O — User I/O pin (bank 2) |
| ピン 16 | VCCIO2 — I/O bank 2 supply voltage |
| ピン 17 | I/O — User I/O pin (bank 2) |
| ピン 18 | I/O — User I/O pin (bank 2) |
| ピン 19 | I/O — User I/O pin (bank 2) |
| ピン 20 | I/O — User I/O pin (bank 2) |
| ピン 21 | GND — Ground |
| ピン 22 | I/O — User I/O pin (bank 3) |
| ピン 23 | I/O — User I/O pin (bank 3) |
| ピン 24 | I/O — User I/O pin (bank 3) |
| ピン 25 | I/O — User I/O pin (bank 3) |
| ピン 26 | VCCIO3 — I/O bank 3 supply voltage |
| ピン 27 | I/O — User I/O pin (bank 3) |
| ピン 28 | I/O — User I/O pin (bank 3) |
| ピン 29 | I/O — User I/O pin (bank 3) |
| ピン 30 | I/O — User I/O pin (bank 3) |
| ピン 31 | GND — Ground |
| ピン 32 | I/O — User I/O pin (bank 4) |
| ピン 33 | I/O — User I/O pin (bank 4) |
| ピン 34 | I/O — User I/O pin (bank 4) |
| ピン 35 | I/O — User I/O pin (bank 4) |
| ピン 36 | VCCIO4 — I/O bank 4 supply voltage |
| ピン 37 | I/O — User I/O pin (bank 4) |
| ピン 38 | I/O — User I/O pin (bank 4) |
| ピン 39 | I/O — User I/O pin (bank 4) |
| ピン 40 | I/O — User I/O pin (bank 4) |
| ピン 41 | GND — Ground |
| ピン 42 | CLK0 — Clock input 0 (LVTTL/LVCMOS) |
| ピン 43 | CLK1 — Clock input 1 (LVTTL/LVCMOS) |
| ピン 44 | I/O — User I/O pin (bank 4) |
| ピン 45 | I/O — User I/O pin (bank 4) |
| ピン 46 | VCCINT — Core supply voltage (1.5 V) |
| ピン 47 | I/O — User I/O pin (bank 4) |
| ピン 48 | I/O — User I/O pin (bank 4) |
| ピン 49 | I/O — User I/O pin (bank 4) |
| ピン 50 | I/O — User I/O pin (bank 4) |
| ピン 51 | GND — Ground |
| ピン 52 | I/O — User I/O pin (bank 4) |
| ピン 53 | I/O — User I/O pin (bank 4) |
| ピン 54 | I/O — User I/O pin (bank 4) |
| ピン 55 | I/O — User I/O pin (bank 4) |
| ピン 56 | VCCIO4 — I/O bank 4 supply voltage |
| ピン 57 | I/O — User I/O pin (bank 4) |
| ピン 58 | I/O — User I/O pin (bank 4) |
| ピン 59 | I/O — User I/O pin (bank 4) |
| ピン 60 | I/O — User I/O pin (bank 4) |
| ピン 61 | GND — Ground |
| ピン 62 | I/O — User I/O pin (bank 4) |
| ピン 63 | I/O — User I/O pin (bank 4) |
| ピン 64 | I/O — User I/O pin (bank 4) |
| ピン 65 | I/O — User I/O pin (bank 4) |
| ピン 66 | VCCA_PLL — PLL analog supply (1.5 V) |
| ピン 67 | I/O — User I/O pin (bank 4) |
| ピン 68 | I/O — User I/O pin (bank 4) |
| ピン 69 | I/O — User I/O pin (bank 4) |
| ピン 70 | I/O — User I/O pin (bank 4) |
| ピン 71 | GND — Ground |
| ピン 72 | I/O — User I/O pin (bank 4) |
| ピン 73 | I/O — User I/O pin (bank 4) |
| ピン 74 | I/O — User I/O pin (bank 4) |
| ピン 75 | I/O — User I/O pin (bank 4) |
| ピン 76 | VCCD_PLL — PLL digital supply (1.5 V) |
| ピン 77 | nCONFIG — Configuration start (active-low) |
| ピン 78 | nSTATUS — Configuration status (active-low) |
| ピン 79 | CONF_DONE — Configuration done indicator |
| ピン 80 | DCLK — Configuration clock input |
| ピン 81 | TDI — JTAG test data input |
| ピン 82 | TMS — JTAG test mode select |
| ピン 83 | TCK — JTAG test clock |
| ピン 84 | TDO — JTAG test data output |
| ピン 85 | MSEL0 — Configuration mode select 0 |
| ピン 86 | MSEL1 — Configuration mode select 1 |
| ピン 87 | DATA0 — Configuration data input (AS/PS) |
| ピン 88 | I/O — User I/O pin (bank 4) |
| ピン 89 | I/O — User I/O pin (bank 4) |
| ピン 90 | I/O — User I/O pin (bank 4) |
| ピン 91 | I/O — User I/O pin (bank 4) |
| ピン 92 | VCCIO4 — I/O bank 4 supply voltage |
| ピン 93 | I/O — User I/O pin (bank 4) |
| ピン 94 | I/O — User I/O pin (bank 4) |
| ピン 95 | I/O — User I/O pin (bank 4) |
| ピン 96 | I/O — User I/O pin (bank 4) |
| ピン 97 | GND — Ground |
| ピン 98 | I/O — User I/O pin (bank 1) |
| ピン 99 | I/O — User I/O pin (bank 1) |
| ピン 100 | I/O — User I/O pin (bank 1) |
主な用途
EP1C3T100C8 の用途: 6 件s: Industrial Glue Logic Replacement, Custom Peripheral Bridge (UART/SPI/I2C to Parallel), Legacy Peripheral Replacement and Form-Fit-Function Drop-In, Educational and Prototyping Boards, Motor-Control Co-Processor, Production Test Fixture Controller.
Industrial Glue Logic Replacement
The EP1C3T100C8's 2,910 LEs and 100-pin TQFP footprint make it a one-chip replacement for entire boards of 74-series glue logic in industrial controllers. Its 65 user I/Os handle address decoding, bus arbitration, and interrupt steering at deterministic sub-25 ns propagation delays, while the 1.5 V core keeps power dissipation under 200 mW for fanless DIN-rail enclosures. Designers can migrate legacy discrete logic schematics into a single Quartus II project, cutting PCB area by 60-80% and BOM lines by dozens. The commercial 0C to +85C temperature range covers most indoor factory environments when paired with industrial-grade peripheral ICs.
おすすめ
Custom Peripheral Bridge (UART/SPI/I2C to Parallel)
With 59,904 bits of M4K block RAM and 8 global clock networks, the EP1C3T100C8 is well suited as a multi-protocol peripheral bridge that converts UART, SPI, and I2C traffic into a parallel bus for legacy microcontrollers. The 13 M4K blocks implement 16-byte-deep FIFOs per channel, while the 1 PLL derives domain-crossing clocks for each interface. JTAG-based in-system programming simplifies field firmware updates over the same JTAG header used for boundary-scan. Cyclone I's 0.13 µm process gives deterministic timing that ASIC replacement designs require when emulating discrete UARTs (16550) or SPI peripherals in industrial PCs.
おすすめ
Legacy Peripheral Replacement and Form-Fit-Function Drop-In
The EP1C3T100C8 is widely used as a firmware-driven replacement for obsolete peripheral ICs whose original silicon is no longer available. Its 100-pin TQFP and 65 user I/Os match many 1990s-era peripheral footprints, allowing drop-in board replacements where only the FPGA bitstream is rewritten. Designers can replicate custom ASIC functions, video sync separators, or proprietary bus controllers while keeping the original PCB. The 1.5 V core plus selectable VCCIO banks (1.5/1.8/2.5/3.3 V) ensures compatibility with both legacy 5 V-tolerant buses via external resistors and modern 1.8 V LVCMOS peripherals on the same board.
おすすめ
Educational and Prototyping Boards
University digital-logic labs and FPGA training courses have long standardized on the EP1C3T100C8 because the 100-pin TQFP is hand-solderable for student assembly and the 2,910 LE capacity is large enough for full RISC-V or MIPS soft-core implementations, yet small enough to fit in low-cost Altera/Intel DE-series and Terasic training boards. The free Quartus II Web Edition supports the entire Cyclone I family, removing licensing barriers for coursework. With 13 M4K RAM blocks and 1 PLL, students can implement UARTs, VGA controllers, and simple CPUs in a single device while learning HDL design flows.
おすすめ
Motor-Control Co-Processor
The EP1C3T100C8 serves as a deterministic co-processor next to a microcontroller in BLDC and stepper motor drives, offloading PWM generation, encoder quadrature decoding, and field-oriented control loops at sub-microsecond jitter. Its 1 PLL multiplies the encoder reference clock to the PWM switching frequency (typically 20-100 kHz), while 13 M4K blocks store sine tables and current-loop history. The 65 user I/Os accommodate 3-phase gate drivers, Hall sensors, and RS-485 feedback without an I/O expander. Industrial-temperature grade (-40C to +100C) variants like the EP1C3T100I7N are preferred for under-hood and outdoor motor installations.
おすすめ
Production Test Fixture Controller
In-circuit test (ICT) and functional test fixtures use the EP1C3T100C8 as a flexible pattern generator and boundary-scan controller. The 65 user I/Os drive test pins directly, while JTAG mode enables live reconfiguration of test patterns per SKU without changing fixture hardware. The 1.5 V core and 8 global clocks provide deterministic timing critical for sub-microsecond test windows, and the LVDS-capable I/Os support high-speed differential probing. Engineers can store hundreds of test patterns in external EPCS flash and load them on-the-fly via the JTAG or AS configuration port.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EP1C3T100C8 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EP1C3T100C8N | EP1C3T100I7N | EP1C3T100C7N | EP1C3T100C6N |
|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel |
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 2,910 LEs | 2,910 LEs | 2,910 LEs | 2,910 LEs | 2,910 LEs |
| Speed Grade | -8 (slowest) | -8 | -7 (faster) | -7 (faster) | -6 (fastest) |
| Temperature Grade | Commercial (0C to +85C) | Commercial | Industrial (-40C to +100C) | Commercial | Commercial |
| Lead-Free (RoHS) | No (SnPb) | Yes (RoHS) | Yes (RoHS) | Yes (RoHS) | Yes (RoHS) |
| User I/O Pins | 65 | 65 | 65 | 65 | 65 |
| Core Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Lifecycle | EOL (PDN1810, since 2019) | EOL (PDN1810) | EOL (PDN1810) | EOL (PDN1810) | EOL (PDN1810) |
| Approx. Unit Price (qty 1000) | $9.75 | $10.50 | $14.20 | $11.80 | $13.50 |
主な差別化要因
- Commercial temperature, lead-free RoHS finish in same TQFP-100 footprint （vs EP1C3T100C8)
- Faster -7 speed grade for timing-critical designs in same TQFP-100 package （vs EP1C3T100C7N)
- Industrial temperature range for harsh environments in same TQFP-100 package （vs EP1C3T100I7N)
設計ノート
The EP1C3T100C8 requires a clean 1.5 V VCCINT supply with a tolerance of +/-5% and a 3.3 V, 2.5 V, 1.8 V, or 1.5 V VCCIO per bank. Use a low-dropout regulator (e.g., TI TPS7A4515 or equivalent) for VCCINT, and place 0.1 µF + 10 µF decoupling capacitors within 5 mm of each VCCINT pin per the Cyclone I datasheet decoupling recommendations. Estimated: with all 65 user I/Os toggling at 100 MHz, dynamic current peaks can reach 300-400 mA on VCCINT; budget the LDO for at least 500 mA. For PLL supplies (VCCA_PLL, VCCD_PLL), use a pi-filter (ferrite bead + 10 µF + 0.1 µF) to isolate PLL noise from the core supply.
Route configuration pins (nCONFIG, nSTATUS, CONF_DONE, DCLK, MSEL0, MSEL1, DATA0) away from switching I/O signals to prevent corruption during configuration. Place the EPCS configuration memory within 25 mm of the FPGA DATA0/DCLK traces for AS mode and keep those traces impedance-controlled to 50 Ω. The 100-pin TQFP has a 0.5 mm pitch; use 0.15 mm trace/space rules and a 4-layer PCB with a dedicated ground plane for return paths. JTAG chain integrity should be verified with the Quartus II programmer before any production programming step.
Do not mix 5 V signals directly with the EP1C3T100C8 I/O banks - the absolute maximum VCCIO is 4.6 V and any over-voltage will permanently damage the device. Use a level translator (e.g., SN74AVC8T245) for 5 V-to-3.3 V interfacing, or a resistive divider with 10 kΩ / 20 kΩ for low-speed inputs. Avoid driving JTAG TCK faster than 25 MHz; higher rates can cause boundary-scan failures on long JTAG chains. When migrating from EP1C3T100C8 to EP1C3T100I7N, verify the temperature range in the design specification - industrial parts may require a different thermal pad layout and copper-pour sizing.
For 100-pin TQFP (14x14 mm, 0.5 mm pitch), use a 4-layer stack-up with signal-top, GND-plane, power-plane, signal-bottom to provide continuous return paths for high-speed LVDS and clock traces. Place VCCIO and VCCINT decoupling as a 0.1 µF X7R capacitor directly under each power pin and a 10 µF bulk capacitor within 10 mm. Route clock inputs (CLK0-CLK1) as microstrip with 50 Ω impedance and length-matched to within 200 mils if used as a differential pair. Keep PLL analog supplies (VCCA_PLL, VCCD_PLL) on a quiet island of the power plane, separated from digital VCCINT by at least 3 mm.
コンプライアンス情報
EP1C3T100C8 is SnPb (non-lead-free); choose EP1C3T100C8N suffix variant for RoHS compliance. Part is EOL per PDN1810 since 2019. AEC-Q100 not applicable to commercial-grade FPGAs; use industrial-temperature variant for harsh environments.
