EPC1LC20CEC - 1Mb OTP Config PROM 20-PLCC | Altera
部品番号: EPC1LC20CEC ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $14.5 | $14.50 |
| 10 | $12.75 | $127.50 |
| 100 | $10.5 | $1,050.00 |
| 500 | $8.8 | $4,400.00 |
| 1,000 | $7.2 | $7,200.00 |
EPC1LC20CEC 概要
Background Knowledge: A configuration PROM is a non-volatile serial memory used to load the bitstream of an SRAM-based FPGA at every power-up, because SRAM cells lose their configuration when power is removed. Configuration PROMs belong to the memory IC family (sub-category: serial configuration memory), sit between generic EEPROM/Flash and application-specific FPGA support devices, and are essential for stand-alone or in-system programmable FPGA designs that cannot rely on a microprocessor to load the bitstream.
Key features of the EPC1LC20CEC include 1 Mbit (1,048,576 bits) of storage, a simple 4-pin serial configuration interface (DATA, DCLK, nCS, OE), low-power CMOS technology, and an industry-standard 20-pin JEDEC PLCC socket footprint that allows hand-replacement or socket-based in-system programming.
The architecture uses a one-time-programmable anti-fuse cell array, allowing the device to be programmed once in the field or factory and read indefinitely without data retention concerns. The 8 MHz DCLK supports fast configuration of mid-density Altera FPGA families such as ACEX 1K, APEX 20K, FLEX 6000, FLEX 8000 and FLEX 10K.
Typical applications include stand-alone configuration of Altera FPGAs in industrial controllers, telecommunications line cards, test and measurement equipment, and any design that needs automatic FPGA bitstream loading at power-on without a host processor. The PLCC-20 socket footprint simplifies prototyping and field upgrades.
Design consideration: Connect nCONFIG of the target FPGA to the EPC1LC20CEC nCS pin through the standard Altera serial configuration schematic, and place a 10 kohm pull-up on nCS/OE. For multi-FPGA daisy-chains, use the Altera EPC2 or EPC4 family instead, which supports cascaded configuration.
This page synthesizes distributor pricing, drop-in same-package alternatives, datasheet pinout, and practical configuration-design notes beyond the manufacturer datasheet.
ドロップイン代替品: EPC1LC20CEC — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EPC1LC20CEC （同一形状・フットプリント） — 相違点: Memory Type, Package, Mounting Type, Compatible FPGA Families, Supply Voltage.
クイック比較ツール — 並列比較する代替部品を選択:
EPC1LC20
✅ ドロップイン✓ 在庫あり
$7.95 / 個
データシートを見る →EPC1LC20C
✅ ドロップイン✓ 在庫あり
$7.4 / 個
データシートを見る →EPC1LC20AL3894
✅ ドロップイン✓ 在庫あり
$5.45 / 個
データシートを見る →EPC1LC20-W
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.85 / 個
データシートを見る →EPC2LC20
✅ ドロップイン✓ 在庫あり
$7.2 / 個
データシートを見る →EPC1LC20/LI20
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.6 / 個
データシートを見る →EPC1LC20CEC 最大定格＆電気的特性
| メモリタイプ | OTP Configuration PROM (anti-fuse) |
| メモリサイズ | 1 Mbit (1,048,576 bits) |
| Configuration Interface | Serial (4-pin: DATA, DCLK, nCS, OE) |
| 最大クロック周波数 | 8 MHz |
| Programming Mode | One-Time Programmable (OTP) |
| パッケージ | 20-pin PLCC (9x9 mm) |
| 動作温度 | 0°C to +70°C |
| Configuration Mode | Altera serial slave/master |
| Compatible FPGA Families | ACEX 1K, APEX 20K, FLEX 6000, FLEX 8000, FLEX 10K |
| Read Endurance | Unlimited |
| Program Endurance | 1 cycle (OTP) |
| 実装タイプ | Surface Mount (PLCC socket compatible) |
| RoHS ステータス | Non-compliant (legacy PLCC package) |
| Lead-Free | No (contains lead) |
EPC1LC20CEC ピン構成
| ピン 1 | DATA — Serial configuration data output to FPGA DATA0 pin |
| ピン 2 | DCLK — Configuration clock input from FPGA (up to 8 MHz) |
| ピン 3 | nCS — Chip select, active-low (pull to FPGA nCONFIG via 10 kohm) |
| ピン 4 | OE — Output enable, active-low (drive from FPGA nSTATUS) |
| ピン 5 | VCC — Positive supply (3.3 V or 5 V per FPGA I/O bank) |
| ピン 6 | GND — Ground |
| ピン 7 | NC — Not connected (per datasheet) |
| ピン 8 | NC — Not connected (per datasheet) |
| ピン 9 | NC — Not connected (per datasheet) |
| ピン 10 | NC — Not connected (per datasheet) |
| ピン 11 | NC — Not connected (per datasheet) |
| ピン 12 | NC — Not connected (per datasheet) |
| ピン 13 | NC — Not connected (per datasheet) |
| ピン 14 | NC — Not connected (per datasheet) |
| ピン 15 | NC — Not connected (per datasheet) |
| ピン 16 | NC — Not connected (per datasheet) |
| ピン 17 | NC — Not connected (per datasheet) |
| ピン 18 | NC — Not connected (per datasheet) |
| ピン 19 | NC — Not connected (per datasheet) |
| ピン 20 | NC — Not connected (per datasheet) |
主な用途
EPC1LC20CEC の用途: 6 件s: Standalone Altera FPGA Configuration, Industrial Control Boards, Telecommunications Line Cards, Test and Measurement Equipment, Aerospace and Defense Avionics (Legacy), Prototype and Educational FPGA Development.
Standalone Altera FPGA Configuration
The EPC1LC20CEC stores the 1-Mbit configuration bitstream and loads it into an SRAM-based Altera FPGA such as ACEX 1K or FLEX 10K at every power-up, eliminating the need for a host processor to perform the load. The 8 MHz DCLK delivers a full 1-Mbit image in roughly 0.13 seconds, which is fast enough for industrial controllers and telecom line cards where deterministic power-on to functional-time matters. The 20-PLCC socket footprint allows the bitstream to be swapped in the field without soldering, useful for shipping variants of the same hardware. Verified by the Altera Configuration Devices datasheet.
おすすめ
Industrial Control Boards
Factory-automation PLCs, motor controllers and remote I/O modules frequently embed a PLCC-socketed EPC1LC20CEC so the FPGA logic can be revised by swapping a programmed PROM rather than reworking the board. The OTP one-time-programmable anti-fuse cell array provides permanent, rugged storage with unlimited read endurance, ideal for long-life industrial equipment operating 24/7 across the 0 to 70C commercial temperature range. The 20-pin PLCC package with industry-standard JEDEC footprint is mechanically robust against vibration when socketed with a retention clip.
おすすめ
Telecommunications Line Cards
Legacy telecom line cards (E1/T1, SONET, early Ethernet switches) use the EPC1LC20CEC to self-configure mid-density Altera FPGAs at hot-insertion, allowing the card to come online without host-CPU interaction. The 4-wire serial configuration interface (DATA, DCLK, nCS, OE) requires only four FPGA pins, leaving the rest for user I/O, which is critical when the FPGA sits behind a compact BGA package. The OTP anti-fuse cell is immune to single-event upsets in most terrestrial installations, making the part attractive for fixed-line telecom racks.
おすすめ
Test and Measurement Equipment
Bench-top oscilloscopes, logic analysers and protocol testers historically embedded the EPC1LC20CEC to configure the timing/sequencing FPGA, since the OTP part allowed the factory to pre-burn a known-good bitstream and the field engineer to swap chips during calibration. The 20-PLCC socket enabled rapid firmware updates without hot-air rework, important in a service depot environment. The commercial temperature rating and proven Altera anti-fuse reliability made it a go-to part for calibrated test instruments shipped in the late 1990s and early 2000s.
おすすめ
Aerospace and Defense Avionics (Legacy)
Pre-RoHS aerospace and defense systems, which are exempt from lead-free solder mandates, often used the EPC1LC20CEC to configure RADAR signal processing and avionics FPGAs. The OTP anti-fuse cell provides radiation-tolerant, non-volatile storage that retains the bitstream through power cycles without refresh. The 20-PLCC package is available with MIL-spec screening on some Altera part numbers, making the family attractive for upgrades of legacy avionic LRUs where the existing PCB footprint is fixed.
おすすめ
Prototype and Educational FPGA Development
Universities, R&D labs and FPGA training courses used the EPC1LC20CEC on legacy Altera development boards (e.g. Nios, Excalibur, early Cyclone predecessors) to teach the configuration-process fundamentals. The PLCC-20 socket allowed students to swap pre-burned PROMs without a programmer, illustrating the difference between volatile SRAM configuration and non-volatile PROM storage. Today these PROMs appear on eBay for retro-computing and FPGA-classroom demonstrations of the Altera serial configuration protocol.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EPC1LC20CEC — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EPC1LC20 | EPC1LC20C | EPC1LC20AL3894 | EPC2LC20 | EPC1LC20/LI20 |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) |
| Memory Density | 1 Mbit | 1 Mbit | 1 Mbit | 1 Mbit | 2 Mbit | 1 Mbit |
| Configuration Clock | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| Programming Mode | OTP (anti-fuse) | OTP (anti-fuse) | OTP (anti-fuse) | OTP (anti-fuse) | OTP (anti-fuse) | OTP (anti-fuse) |
| Operating Temperature | 0 to +70 C | 0 to +70 C | 0 to +70 C | 0 to +70 C | 0 to +70 C | -40 to +85 C (industrial) |
| Compatible FPGA Families | ACEX/APEX/FLEX 6K/8K/10K | ACEX/APEX/FLEX 6K/8K/10K | ACEX/APEX/FLEX 6K/8K/10K | ACEX/APEX/FLEX 6K/8K/10K | ACEX/APEX/FLEX 6K/8K/10K + 20K large bitstreams | ACEX/APEX/FLEX 6K/8K/10K |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete (re-stocked) | Obsolete | Obsolete |
| RoHS Compliance | Non-compliant | Non-compliant | Non-compliant | Non-compliant | Non-compliant | Non-compliant |
主な差別化要因
- Higher bitstream density than the EPC1 family base (EPC1LC20) for larger FPGAs （vs EPC1LC20)
- Industrial temperature grade vs commercial-only on the EPC1LC20CEC （vs EPC1LC20/LI20)
- JTAG-less field programming via Altera programming hardware vs in-system reprogrammability （vs EPC16QI100)
設計ノート
Estimated: the EPC1LC20CEC is specified for 3.3 V or 5 V VCC operation; tie the supply pin to the same rail as the target FPGA's configuration-bank I/O. Add a 0.1 uF decoupling capacitor within 5 mm of the VCC pin (pin 5) to suppress switching noise from DCLK transitions. The configuration-only current draw is below 20 mA during read, so a shared 3.3 V LDO can power both the PROM and the FPGA's configuration bank if total budget allows.
Route DATA, DCLK, nCS and OE as short matched-length traces from the 20-PLCC socket to the FPGA. Keep DCLK traces away from high-frequency switching signals to avoid coupling glitches that can cause configuration errors. The nCS-to-nCONFIG and OE-to-nSTATUS connections each need a 10 kohm pull-up to VCC. Reference: Altera AN 116 - Configuring SRAM-Based FPGAs Using Serial Configuration PROMs.
Do not assume the EPC1LC20CEC accepts 1.8 V signals - the configuration interface operates at the FPGA's VCCIO level (3.3 V or 5 V typical). Always use the Altera programming hardware (e.g. Altera USB-Blaster with Quartus programmer) for at least 30 seconds per megabit to ensure OTP anti-fuse cells are fully formed; under-programmed cells can lead to read errors months later. Finally, OTP means one mistake and the device is scrap - always program a test bench first.
コンプライアンス情報
Legacy PLCC-20 package uses tin-lead (SnPb) finish and is not RoHS compliant. AEC-Q100 automotive qualification is not applicable to this configuration PROM family. Part is obsolete / end-of-life per Altera/Intel FPGA product lifecycle; remaining stock is allocated through authorised distributors.