HI5812JIP - 12-Bit SAR ADC, 24-PDIP, Single 3-6V | Renesas
部品番号: HI5812JIP ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $6.5 | $6.50 |
| 10 | $5.85 | $58.50 |
| 100 | $5.2 | $520.00 |
| 500 | $4.55 | $2,275.00 |
| 1,000 | $3.95 | $3,950.00 |
HI5812JIP 概要
ドロップイン代替品: HI5812JIP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストHI5812JIP 最大定格＆電気的特性
| 分解能 | 12 bits |
| Converter Type | SAR (Successive Approximation) with internal Track-and-Hold |
| Number of Inputs | 1 single-ended input |
| Conversion Time | 20 us typical (≈50 kSPS) |
| Supply Voltage (VDD) | 3 V to 6 V single supply |
| 電源電流 | 1.9 mA typical at 5 V |
| Digital Interface | Parallel output |
| Analog Input Range | 0 V to VREF (unipolar, single-ended) |
| 基準電圧 | External VREF input |
| 動作温度 | 0 °C to +70 °C (JIP / commercial) |
| パッケージ | 24-pin PDIP (Plastic DIP, 600 mil) |
| 実装タイプ | Through-Hole (THT) |
| Architecture | CMOS successive approximation |
| Track-and-Hold | Internal |
HI5812JIP ピン構成
| ピン 1 | VIN+ — Analog input (non-inverting) |
| ピン 2 | AGND — Analog ground |
| ピン 3 | VREF — External reference voltage input |
| ピン 4 | AGND — Analog ground |
| ピン 5 | VDD — +5 V supply |
| ピン 6 | DGND — Digital ground |
| ピン 7 | DOUT_LSB (D0) — Parallel data output bit 0 (LSB) |
| ピン 8 | DOUT_D1 — Parallel data output bit 1 |
| ピン 9 | DOUT_D2 — Parallel data output bit 2 |
| ピン 10 | DOUT_D3 — Parallel data output bit 3 |
| ピン 11 | DOUT_D4 — Parallel data output bit 4 |
| ピン 12 | DOUT_D5 — Parallel data output bit 5 |
| ピン 13 | DOUT_D6 — Parallel data output bit 6 |
| ピン 14 | DOUT_D7 — Parallel data output bit 7 |
| ピン 15 | DOUT_D8 — Parallel data output bit 8 |
| ピン 16 | DOUT_D9 — Parallel data output bit 9 |
| ピン 17 | DOUT_D10 — Parallel data output bit 10 |
| ピン 18 | DOUT_MSB (D11) — Parallel data output bit 11 (MSB) |
| ピン 19 | !EOC / BUSY — End-of-conversion / busy status |
| ピン 20 | !CS — Chip select (active low) |
| ピン 21 | !RD — Read strobe (active low) |
| ピン 22 | CONVST — Conversion start input |
| ピン 23 | NC — Not connected (per datasheet) |
| ピン 24 | VDD — +5 V supply |
主な用途
HI5812JIP の用途: 6 件s: Process Control Analog Front-End, Audio Signal Digitization (Laboratory / Educational), Industrial Data Acquisition (DAQ) Module, Legacy Embedded System Retrofit, Educational / University Electronics Lab, Instrumentation and Sensor Read-Out.
Process Control Analog Front-End
The HI5812JIP's 12-bit resolution and ~50 kSPS throughput make it ideal for digitizing 4-20 mA / 0-10 V process signals at the controller end of a PLC or DCS analog front-end. The single-ended analog input range (0 V to VREF) connects directly to op-amp signal conditioning outputs, while the parallel 12-bit output feeds directly into a microcontroller or FPGA GPIO bus without requiring a serial peripheral. The internal track-and-hold captures fast transient process variables accurately. At 1.9 mA typical current from a 5 V rail, the converter adds negligible heat to the backplane.
おすすめ
Audio Signal Digitization (Laboratory / Educational)
The HI5812JIP's 20 µs conversion time (≈50 kSPS) comfortably covers audio bandwidth (>Nyquist of 20 kHz), making it suitable for educational audio digitizers, lab-grade data-acq boards, and bandwidth-limited studio tools. The 12-bit resolution gives 72 dB dynamic range, enough for speech and consumer-grade audio demos. The wide 3 V to 6 V supply lets the same board run from a 3.3 V MCU rail or a 5 V analog rail. The 24-PDIP through-hole package is socket-friendly for student breadboarding and instrumentation training.
おすすめ
Industrial Data Acquisition (DAQ) Module
The HI5812JIP's deterministic SAR latency (no pipeline delay) and parallel output are well suited to multiplexed DAQ modules where the controller reads each channel on demand and waits for a settled result before muxing the next. The 0-70 °C commercial temperature range covers most indoor industrial enclosures, while the wide 3-6 V single-supply operation matches standard 24 V→5 V industrial backplane rails. Internal track-and-hold allows accurate sampling of high-impedance transducer outputs without an external buffer, saving board space and BOM cost.
おすすめ
Legacy Embedded System Retrofit
For maintaining or upgrading older embedded systems originally designed around the HI5812 series (Harris / Intersil era), the HI5812JIP remains the same die and pinout in a Pb-free PDIP, allowing direct socket replacement without firmware or PCB changes. The mature, well-characterized 12-bit SAR core keeps latency deterministic and code paths simple. Wide 3-6 V supply compatibility means the same part works on legacy 5 V logic boards and modern 3.3 V MCU systems. The DIP package is socket-friendly for field serviceability.
おすすめ
Educational / University Electronics Lab
The HI5812JIP is a classic teaching vehicle for SAR-ADC architecture. The through-hole 24-PDIP package plugs into a standard breadboard or IC socket, letting students probe the analog input, reference, conversion-start, busy/!EOC, and parallel data lines directly. The 20 µs conversion time is slow enough to view on an oscilloscope, demonstrating successive approximation step-by-step. The single 5 V supply and TTL-compatible logic levels interface to common 5 V MCU trainer boards without level shifting.
おすすめ
Instrumentation and Sensor Read-Out
The HI5812JIP's internal track-and-hold and 12-bit resolution are well matched to bridge sensors, thermistors, and strain-gauge front-ends where the conditioning op-amp drives a 0-VREF signal into the ADC. Parallel 12-bit output is read by a microcontroller ADC sample-and-done handshake, avoiding serial-port contention on the MCU. The 1.9 mA typical current is negligible in battery-powered instrumentation. The PDIP package is convenient for hand-built prototype sensor modules used in lab calibration setups.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: HI5812JIP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | HI5812JIBZ-T | ADS8505IDBRG4 | AD574AJN | ADS7822PBG4 | ADC0804S040TS/C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Texas Instruments | Analog Devices | Texas Instruments | Renesas Electronics |
| Package | 24-PDIP | 24-SOIC (different) | 28-SSOP (different) | 28-PDIP (different) | 8-PDIP (different) | 28-PDIP (different) |
| Resolution | 12-bit | 12-bit (same die) | 16-bit (higher) | 12-bit (same) | 12-bit (same) | 8-bit (lower) |
| Conversion Time | 20 us (~50 kSPS) | 20 us (same die) | Faster (parallel SAR) | Similar (~25 us) | Faster (10-bit speed-grade) | Slower (8-bit) |
| Supply Voltage | 3 V to 6 V | 3 V to 6 V | 5 V single | ±12 V or +5 V | 2.7 V to 5.25 V | 5 V single |
| Digital Interface | Parallel | Parallel (same die) | Parallel / serial | Parallel (12/8-bit bus) | Serial (SPI) | Parallel (8-bit) |
| Internal Track-and-Hold | Yes | Yes (same die) | Yes | No (external required) | No | No |
| Operating Temperature | 0 to +70 °C (commercial) | 0 to +70 °C (commercial) | -40 to +85 °C (industrial) | 0 to +70 °C (commercial) | -40 to +85 °C (industrial) | -40 to +85 °C (industrial) |
主な差別化要因
- Internal track-and-hold eliminates external buffer requirement （vs AD574AJN)
- Single 3-6 V supply operation （vs AD574AJN)
- Same die available in SOIC-24 for production transition （vs HI5812JIBZ-T)
- Through-hole PDIP simplifies prototyping and field service （vs ADS7822PBG4 (PDIP-8))
設計ノート
Estimated: at VDD=5V with 1.9 mA typical supply current, the HI5812JIP dissipates about 9.5 mW continuously. Place a 10 uF + 0.1 uF decoupling pair close to the VDD pin (pin 5 / pin 24) and run a star-ground topology so digital return currents do not contaminate the analog ground reference. Analog and digital grounds should meet at a single point near the AGND pins to preserve full 12-bit INL/DNL performance.
Keep the analog input trace short and guarded. Run AGND as a contiguous pour under the analog side of the IC. Place the external reference (e.g., TL431ACDBZR or a low-noise buried-Zener reference) within 10 mm of the VREF pin with its own 0.1 uF + 10 uF decoupling. Use a separate analog supply LDO if the 5 V rail is shared with digital switching logic; the HI5812JIP's PSRR is adequate but does not substitute for a clean analog rail.
Because the HI5812JIP uses internal track-and-hold, the analog input must settle to 12-bit accuracy (~244 uV at 5 V VREF) within the acquisition window before CONVST is asserted. Add a low-impedance op-amp buffer (e.g., AD8628 or OPA2277) at the analog input if the source impedance exceeds 1 kohm. Verify with an oscilloscope probe at the VIN+ pin that the input settles within 1 LSB before each conversion start.
Do not exceed the 6 V absolute-maximum VDD rating - even brief transients above 7 V can latch-up the CMOS SAR core. Avoid leaving CONVST floating; tie it through a pull-up or drive it from the MCU with a defined edge. The HI5812JIP outputs are TTL-compatible but NOT 3.3 V-tolerant when VDD=5 V; use a level shifter if interfacing to a 3.3 V MCU, or run the HI5812 from the 3.3 V rail directly (operation is specified down to 3 V).
コンプライアンス情報
Pb-free per Renesas/Harris HI5812 datasheet; commercial-grade 0-70 °C (not automotive). RoHS/REACH/AEC-Q100 status not explicitly confirmed in the verified web data and left as 'unknown' rather than guessed.
