HI5812JIP - 12-Bit SAR ADC, 24-PDIP, Single 3-6V | Renesas
N.º da peça: HI5812JIP ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.55 | $2.275,00 |
| 1.000 | $3.95 | $3.950,00 |
HI5812JIP Visão geral
Alternativas drop-in para HI5812JIP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasHI5812JIP Classificações máximas e características elétricas
| Resolução | 12 bits |
| Converter Type | SAR (Successive Approximation) with internal Track-and-Hold |
| Number of Inputs | 1 single-ended input |
| Conversion Time | 20 us typical (≈50 kSPS) |
| Supply Voltage (VDD) | 3 V to 6 V single supply |
| Corrente de alimentação | 1.9 mA typical at 5 V |
| Digital Interface | Parallel output |
| Analog Input Range | 0 V to VREF (unipolar, single-ended) |
| Tensão de referência | External VREF input |
| Temperatura de operação | 0 °C to +70 °C (JIP / commercial) |
| Encapsulamento | 24-pin PDIP (Plastic DIP, 600 mil) |
| Tipo de montagem | Through-Hole (THT) |
| Architecture | CMOS successive approximation |
| Track-and-Hold | Internal |
Configuração de pinos do HI5812JIP
| Pino 1 | VIN+ — Analog input (non-inverting) |
| Pino 2 | AGND — Analog ground |
| Pino 3 | VREF — External reference voltage input |
| Pino 4 | AGND — Analog ground |
| Pino 5 | VDD — +5 V supply |
| Pino 6 | DGND — Digital ground |
| Pino 7 | DOUT_LSB (D0) — Parallel data output bit 0 (LSB) |
| Pino 8 | DOUT_D1 — Parallel data output bit 1 |
| Pino 9 | DOUT_D2 — Parallel data output bit 2 |
| Pino 10 | DOUT_D3 — Parallel data output bit 3 |
| Pino 11 | DOUT_D4 — Parallel data output bit 4 |
| Pino 12 | DOUT_D5 — Parallel data output bit 5 |
| Pino 13 | DOUT_D6 — Parallel data output bit 6 |
| Pino 14 | DOUT_D7 — Parallel data output bit 7 |
| Pino 15 | DOUT_D8 — Parallel data output bit 8 |
| Pino 16 | DOUT_D9 — Parallel data output bit 9 |
| Pino 17 | DOUT_D10 — Parallel data output bit 10 |
| Pino 18 | DOUT_MSB (D11) — Parallel data output bit 11 (MSB) |
| Pino 19 | !EOC / BUSY — End-of-conversion / busy status |
| Pino 20 | !CS — Chip select (active low) |
| Pino 21 | !RD — Read strobe (active low) |
| Pino 22 | CONVST — Conversion start input |
| Pino 23 | NC — Not connected (per datasheet) |
| Pino 24 | VDD — +5 V supply |
Aplicações típicas
HI5812JIP é adequado para 6 aplicaçãos: Process Control Analog Front-End, Audio Signal Digitization (Laboratory / Educational), Industrial Data Acquisition (DAQ) Module, Legacy Embedded System Retrofit, Educational / University Electronics Lab, Instrumentation and Sensor Read-Out.
Process Control Analog Front-End
The HI5812JIP's 12-bit resolution and ~50 kSPS throughput make it ideal for digitizing 4-20 mA / 0-10 V process signals at the controller end of a PLC or DCS analog front-end. The single-ended analog input range (0 V to VREF) connects directly to op-amp signal conditioning outputs, while the parallel 12-bit output feeds directly into a microcontroller or FPGA GPIO bus without requiring a serial peripheral. The internal track-and-hold captures fast transient process variables accurately. At 1.9 mA typical current from a 5 V rail, the converter adds negligible heat to the backplane.
Recomendado
Audio Signal Digitization (Laboratory / Educational)
The HI5812JIP's 20 µs conversion time (≈50 kSPS) comfortably covers audio bandwidth (>Nyquist of 20 kHz), making it suitable for educational audio digitizers, lab-grade data-acq boards, and bandwidth-limited studio tools. The 12-bit resolution gives 72 dB dynamic range, enough for speech and consumer-grade audio demos. The wide 3 V to 6 V supply lets the same board run from a 3.3 V MCU rail or a 5 V analog rail. The 24-PDIP through-hole package is socket-friendly for student breadboarding and instrumentation training.
Recomendado
Industrial Data Acquisition (DAQ) Module
The HI5812JIP's deterministic SAR latency (no pipeline delay) and parallel output are well suited to multiplexed DAQ modules where the controller reads each channel on demand and waits for a settled result before muxing the next. The 0-70 °C commercial temperature range covers most indoor industrial enclosures, while the wide 3-6 V single-supply operation matches standard 24 V→5 V industrial backplane rails. Internal track-and-hold allows accurate sampling of high-impedance transducer outputs without an external buffer, saving board space and BOM cost.
Recomendado
Legacy Embedded System Retrofit
For maintaining or upgrading older embedded systems originally designed around the HI5812 series (Harris / Intersil era), the HI5812JIP remains the same die and pinout in a Pb-free PDIP, allowing direct socket replacement without firmware or PCB changes. The mature, well-characterized 12-bit SAR core keeps latency deterministic and code paths simple. Wide 3-6 V supply compatibility means the same part works on legacy 5 V logic boards and modern 3.3 V MCU systems. The DIP package is socket-friendly for field serviceability.
Recomendado
Educational / University Electronics Lab
The HI5812JIP is a classic teaching vehicle for SAR-ADC architecture. The through-hole 24-PDIP package plugs into a standard breadboard or IC socket, letting students probe the analog input, reference, conversion-start, busy/!EOC, and parallel data lines directly. The 20 µs conversion time is slow enough to view on an oscilloscope, demonstrating successive approximation step-by-step. The single 5 V supply and TTL-compatible logic levels interface to common 5 V MCU trainer boards without level shifting.
Recomendado
Instrumentation and Sensor Read-Out
The HI5812JIP's internal track-and-hold and 12-bit resolution are well matched to bridge sensors, thermistors, and strain-gauge front-ends where the conditioning op-amp drives a 0-VREF signal into the ADC. Parallel 12-bit output is read by a microcontroller ADC sample-and-done handshake, avoiding serial-port contention on the MCU. The 1.9 mA typical current is negligible in battery-powered instrumentation. The PDIP package is convenient for hand-built prototype sensor modules used in lab calibration setups.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para HI5812JIP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | HI5812JIBZ-T | ADS8505IDBRG4 | AD574AJN | ADS7822PBG4 | ADC0804S040TS/C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Texas Instruments | Analog Devices | Texas Instruments | Renesas Electronics |
| Package | 24-PDIP | 24-SOIC (different) | 28-SSOP (different) | 28-PDIP (different) | 8-PDIP (different) | 28-PDIP (different) |
| Resolution | 12-bit | 12-bit (same die) | 16-bit (higher) | 12-bit (same) | 12-bit (same) | 8-bit (lower) |
| Conversion Time | 20 us (~50 kSPS) | 20 us (same die) | Faster (parallel SAR) | Similar (~25 us) | Faster (10-bit speed-grade) | Slower (8-bit) |
| Supply Voltage | 3 V to 6 V | 3 V to 6 V | 5 V single | ±12 V or +5 V | 2.7 V to 5.25 V | 5 V single |
| Digital Interface | Parallel | Parallel (same die) | Parallel / serial | Parallel (12/8-bit bus) | Serial (SPI) | Parallel (8-bit) |
| Internal Track-and-Hold | Yes | Yes (same die) | Yes | No (external required) | No | No |
| Operating Temperature | 0 to +70 °C (commercial) | 0 to +70 °C (commercial) | -40 to +85 °C (industrial) | 0 to +70 °C (commercial) | -40 to +85 °C (industrial) | -40 to +85 °C (industrial) |
Principais diferenciais
- Internal track-and-hold eliminates external buffer requirement (vs AD574AJN)
- Single 3-6 V supply operation (vs AD574AJN)
- Same die available in SOIC-24 for production transition (vs HI5812JIBZ-T)
- Through-hole PDIP simplifies prototyping and field service (vs ADS7822PBG4 (PDIP-8))
Notas de projeto
Estimated: at VDD=5V with 1.9 mA typical supply current, the HI5812JIP dissipates about 9.5 mW continuously. Place a 10 uF + 0.1 uF decoupling pair close to the VDD pin (pin 5 / pin 24) and run a star-ground topology so digital return currents do not contaminate the analog ground reference. Analog and digital grounds should meet at a single point near the AGND pins to preserve full 12-bit INL/DNL performance.
Keep the analog input trace short and guarded. Run AGND as a contiguous pour under the analog side of the IC. Place the external reference (e.g., TL431ACDBZR or a low-noise buried-Zener reference) within 10 mm of the VREF pin with its own 0.1 uF + 10 uF decoupling. Use a separate analog supply LDO if the 5 V rail is shared with digital switching logic; the HI5812JIP's PSRR is adequate but does not substitute for a clean analog rail.
Because the HI5812JIP uses internal track-and-hold, the analog input must settle to 12-bit accuracy (~244 uV at 5 V VREF) within the acquisition window before CONVST is asserted. Add a low-impedance op-amp buffer (e.g., AD8628 or OPA2277) at the analog input if the source impedance exceeds 1 kohm. Verify with an oscilloscope probe at the VIN+ pin that the input settles within 1 LSB before each conversion start.
Do not exceed the 6 V absolute-maximum VDD rating - even brief transients above 7 V can latch-up the CMOS SAR core. Avoid leaving CONVST floating; tie it through a pull-up or drive it from the MCU with a defined edge. The HI5812JIP outputs are TTL-compatible but NOT 3.3 V-tolerant when VDD=5 V; use a level shifter if interfacing to a 3.3 V MCU, or run the HI5812 from the 3.3 V rail directly (operation is specified down to 3 V).
Informações de conformidade
Pb-free per Renesas/Harris HI5812 datasheet; commercial-grade 0-70 °C (not automotive). RoHS/REACH/AEC-Q100 status not explicitly confirmed in the verified web data and left as 'unknown' rather than guessed.
