ICM7228BIPI - 8-Digit LED Display Driver DIP-28 | Intersil
部品番号: ICM7228BIPI ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.8 | $1,380.00 |
| 500 | $11.95 | $5,975.00 |
| 1,000 | $9.85 | $9,850.00 |
ICM7228BIPI 概要
An LED display driver is a category of power management / display driver IC that converts parallel or serial digital data into multiplexed segment-drive waveforms suitable for 7-segment numeric or 14/16-segment alphanumeric displays. Within the broader taxonomy, ICM7228BIPI sits at LED Display Driver -> Display Driver -> PMIC -> Power Management -> Integrated Circuit, and serves as a turnkey human-machine interface solution for instruments, meters, and point-of-sale terminals.
Key features include two on-board 7-segment decoder types (Type B for hexadecimal display), 8-byte static RAM that holds digit data independently of the microprocessor, separate segment and digit driver outputs sized for typical LED common-cathode arrays, and a 4-bit data bus with chip-select and write-strobe inputs that allow multiplexing multiple ICM7228 devices on the same bus. The B-suffix variant supports hexadecimal decoding (0-9, A-F) with leading zero blanking, making it suitable for both decimal instrumentation readouts and hex debug displays.
Typical applications include digital panel meters, frequency counters, bench multimeters, industrial process controllers, point-of-sale terminals, instrumentation readouts, and any embedded system that needs to drive a multiplexed 8-digit LED display from a microcontroller without dedicating processor cycles to refresh. The wide operating temperature range supports both industrial and commercial deployments.
When designing with this part, ensure the segment current-setting resistor values are chosen to limit peak segment current below the device's absolute maximum rating (refer to the manufacturer datasheet for the exact value), and add bulk decoupling close to VCC and GND. The 28-pin PDIP footprint is generous and easy to hand-solder or breadboard, making the part popular in legacy designs, education kits, and hobby projects where SMD parts would be inconvenient.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for evaluating the ICM7228BIPI for new designs and field replacements.
ドロップイン代替品: ICM7228BIPI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ICM7228BIPI （同一形状・フットプリント） — 相違点: Display Type, Interface, Package, Operating Temperature, Manufacturer.
クイック比較ツール — 並列比較する代替部品を選択:
ICM7228BIPIZ
✅ ドロップイン✓ 在庫あり
$17.4 / 個
データシートを見る →ICM7228AIPIZ
✅ ドロップイン✓ 在庫あり
$10.75 / 個
データシートを見る →ICM7228DIPI
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ICM7218BIPI+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ICM7218AIPI+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ICM7228BIPI 最大定格＆電気的特性
| Display Type | LED, 7-segment, common-cathode |
| Number of Digits | 8 |
| Configuration | 8-Digit, Microprocessor-Compatible |
| インターフェース | Parallel 4-bit with chip-select and write-strobe |
| Decoder Type | Hexadecimal (Type B, 0-9, A-F) |
| Internal Memory | 8 x 8-bit static RAM for digit data |
| 電源電圧 | 5 V |
| パッケージ | 28-pin PDIP (Plastic DIP) |
| ピン数 | 28 |
| 実装タイプ | Through-Hole |
| Technology | CMOS |
| Manufacturer | Intersil (now part of Renesas) |
| Datasheet Publication Year | 1997 |
ICM7228BIPI ピン構成
| ピン 1 | OSC — Oscillator input for multiplex scan timing |
| ピン 2 | GND — Ground reference |
| ピン 3 | D0 — Data bit 0 input |
| ピン 4 | D1 — Data bit 1 input |
| ピン 5 | D2 — Data bit 2 input |
| ピン 6 | D3 — Data bit 3 input |
| ピン 7 | CS — Chip-select input (active low) |
| ピン 8 | WR — Write-strobe input (active low) |
| ピン 9 | MODE — Mode select input (hex/BCD decode vs direct segment) |
| ピン 10 | SHUTDOWN — Display shutdown input (active low) |
| ピン 11 | DIG1 — Digit 1 driver output (common-cathode sink) |
| ピン 12 | DIG2 — Digit 2 driver output (common-cathode sink) |
| ピン 13 | DIG3 — Digit 3 driver output (common-cathode sink) |
| ピン 14 | DIG4 — Digit 4 driver output (common-cathode sink) |
| ピン 15 | DIG5 — Digit 5 driver output (common-cathode sink) |
| ピン 16 | DIG6 — Digit 6 driver output (common-cathode sink) |
| ピン 17 | DIG7 — Digit 7 driver output (common-cathode sink) |
| ピン 18 | DIG8 — Digit 8 driver output (common-cathode sink) |
| ピン 19 | SEGa — Segment a driver output |
| ピン 20 | SEGb — Segment b driver output |
| ピン 21 | SEGc — Segment c driver output |
| ピン 22 | SEGd — Segment d driver output |
| ピン 23 | SEGe — Segment e driver output |
| ピン 24 | SEGf — Segment f driver output |
| ピン 25 | SEGg — Segment g driver output |
| ピン 26 | SEGdp — Segment decimal-point driver output |
| ピン 27 | VCC — +5 V supply input |
| ピン 28 | NC — Not connected (per datasheet) |
主な用途
ICM7228BIPI の用途: 7 件s: Digital Panel Meter, Frequency Counter Display, Industrial Process Controller, Point-of-Sale Terminal, Bench Multimeter Display, Hobby / Educational Electronics Kit, Legacy Instrumentation Replacement.
Digital Panel Meter
The ICM7228BIPI is well suited for digital panel meter readouts because its 8-digit multiplexed 7-segment drive matches the typical panel-meter digit count and its Type B hexadecimal decoding enables direct readout of calibrated voltage, current, or frequency values without extra firmware. The 28-pin PDIP through-hole package simplifies hand-soldered assembly in low-volume industrial meter housings. Placed between the 5 V logic rail and the 8-digit common-cathode display, the part handles multiplexing and refresh automatically while the host microcontroller only writes digit data on demand. Trade-off: only 8 digits are supported, so wider readouts require an additional driver stage.
おすすめ
Frequency Counter Display
Frequency counters require stable, multiplexed 8-digit readouts that the ICM7228BIPI provides directly without host refresh overhead. The Type B hexadecimal decoding allows direct display of frequency values in kHz or MHz while the internal 8x8 RAM holds the digit data independently of the counter logic. The 5 V single-supply operation matches TTL/CMOS counter front ends, and the 28-pin PDIP footprint supports hand-prototyped bench instruments. Use the chip-select and write-strobe inputs to drive multiple ICM7228 devices from one counter bus if more than 8 digits are needed.
おすすめ
Industrial Process Controller
Industrial process controllers need rugged, reliable human-machine interfaces, and the ICM7228BIPI's mature CMOS design and 28-pin PDIP through-hole construction provide field-replaceable serviceability. The Type B hex decoding supports PID setpoint displays in hexadecimal or decimal, and the 8-digit capacity is sufficient for temperature, flow, and pressure readouts in process plants. Because the part is produced for legacy industrial maintenance, it integrates easily into existing controller boards that use the same footprint. Trade-off: the through-hole package occupies more PCB area than SMD alternatives.
おすすめ
Point-of-Sale Terminal
Point-of-sale (POS) terminals need bright, easy-to-read 8-digit numeric displays for prices, totals, and quantities, all of which the ICM7228BIPI drives directly from a host microcontroller. The internal 8x8 static RAM means that price display data persists between transactions without continuous firmware refresh. The 5 V CMOS interface is compatible with legacy POS mother, and the 28-pin PDIP package allows service technicians to swap displays without reworking SMD pads. This is a mature, field-proven architecture used in POS terminals for decades.
おすすめ
Bench Multimeter Display
Bench multimeters require large, bright 7-segment readouts that the ICM7228BIPI drives through its on-chip multiplex scan and segment drivers. The Type B decoding supports direct hex display of bit-pattern or frequency-mode readings, and the 8-digit capacity suits 6.5-digit meters plus range/function indicators. The 28-pin PDIP package is convenient in hand-built bench instrument prototypes. Trade-off: only common-cathode LED displays are supported, so common-anode displays require an external inverter stage.
おすすめ
Hobby / Educational Electronics Kit
The ICM7228BIPI is a popular building block in microcontroller training kits and hobby projects because its 28-pin PDIP package is breadboard-friendly and hand-solderable. Students learn microprocessor-to-LED-display interfacing using just a parallel data bus, chip-select, and write-strobe line, with no external driver transistors required. The internal 8x8 RAM holds display contents during programming experiments, and the mature datasheet includes clear timing diagrams suitable for educational use. Trade-off: the through-hole package consumes significant breadboard real estate.
おすすめ
Legacy Instrumentation Replacement
Many legacy industrial and scientific instruments use ICM7228-series drivers on 28-pin PDIP footprints, and the ICM7228BIPI is the authentic replacement part for field service. According to the Renesas datasheet, this part is still produced primarily for maintenance of installed equipment, so spare-part inventory is straightforward. The drop-in compatibility with other ICM7228A/B/D variants means service technicians can substitute parts based on availability. Use Rochester Electronics for guaranteed authentic stock in critical MRO applications.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ICM7228BIPI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ICM7228BIPIZ | ICM7228AIPIZ | ICM7228DIPI | ICM7218BIPI+ | ICM7218AIPI+ |
|---|---|---|---|---|---|---|
| Brand | Renesas / Intersil | Renesas / Intersil (same) | Renesas / Intersil (same) | Renesas / Intersil (same) | Maxim Integrated | Maxim Integrated |
| Package | PDIP-28 | PDIP-28 (same) | PDIP-28 (same) | PDIP-28 (same) | PDIP-28 (same) | PDIP-28 (same) |
| Number of Digits | 8 | 8 | 8 | 8 | 8 | 8 |
| Decoder Type | Type B (hexadecimal 0-9, A-F) | Type B (hex) | Type A (decimal 0-9) | Type D (code-B decimal) | Type B (hex) | Type A (decimal) |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Interface | Parallel 4-bit + CS + WR | Parallel 4-bit + CS + WR (same) | Parallel 4-bit + CS + WR (same) | Parallel 4-bit + CS + WR (same) | Parallel 4-bit + CS + WR (same) | Parallel 4-bit + CS + WR (same) |
| Single-Digit Access Mode | Yes (ICM7228 family feature) | Yes (same family) | Yes (same family) | Yes (same family) | No (older family) | No (older family) |
主な差別化要因
- Hexadecimal decoding support (0-9, A-F) （vs ICM7228AIPIZ (Type A decimal))
- ICM7228 family single-digit access mode （vs ICM7218BIPI+ (older generation))
- Renesas/Intersil authentic manufacturing source （vs ICM7218BIPI+ (Maxim Integrated))
設計ノート
The ICM7228BIPI operates from a single +5 V supply. Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VCC pin (pin 27) and a 10 uF bulk electrolytic capacitor on the same supply rail to suppress digital switching noise generated by the on-chip multiplex scan oscillator. Estimated: assuming 8 digits multiplexed at ~200 Hz per digit and average segment current of 5 mA per segment, total supply current is approximately 30-50 mA plus digit-driver currents; refer to the datasheet absolute maximum ratings for the exact segment-current limit before finalizing the series resistor values.
The 28-pin PDIP through-hole package is breadboard-friendly and easy to hand-solder. Keep the segment and digit output traces short and direct to minimize parasitic capacitance on the multiplexed lines, which would otherwise slow the segment-driver rise/fall times and cause ghosting on the LED display. Place the external current-setting resistors (one per segment line) close to the IC pins and route the LED common-cathode returns to a star-ground point tied to the IC GND pin (pin 2). For multi-IC designs, separate analog and digital ground returns to avoid switching-noise coupling into sensitive measurement front-ends.
Do not exceed the absolute maximum segment current specified in the datasheet - the internal segment drivers will source or sink excessive current without external limiting resistors, potentially damaging the IC and the LED display. Always include a series resistor on each segment line sized for your display's Vf and desired brightness. The chip-select (CS, pin 7) and write-strobe (WR, pin 8) inputs are active-low; tying either pin high disables writes but does not blank the display. The shutdown pin (pin 10) blanks the display for power-saving modes - remember to deassert it during normal operation. Software written for the older ICM7218 family may need updates to handle the ICM7228 single-digit access mode.
コンプライアンス情報
RoHS / lead-free status of the original ICM7228BIPI varies by date code and manufacturing lot; the Z-suffix variants ICM7228BIPIZ and ICM7228AIPIZ are explicitly lead-free RoHS-compliant per Renesas ordering information. AEC-Q100 is not applicable because this part is not an automotive-qualified IC. Refer to the manufacturer product page for current RoHS/REACH compliance certificates.
