Texas Instruments

INA141UAG4 - 1 MHz Instrumentation Amplifier | Texas Instruments

部品番号: INA141UAG4 ✗ 生産終了
20 µV Vdss 8-SOIC, 0.154 inch body width, 3.90 mm width Package
MOQ: 1 |

INA141UAG4 概要

The Texas Instruments INA141UAG4 is a precision, low-power instrumentation amplifier with fixed gains of 10 and 100, a bandwidth of 1 MHz, and an 8-SOIC package. It is designed for measuring small differential signals while rejecting common-mode noise, making it suitable for sensor interfaces, industrial measurement systems, and precision analog signal chains. The device also provides an input offset voltage listed as 250 µV and an input-referred noise density of 8 nV/√Hz in the manufacturer product information.

An instrumentation amplifier is a specialized amplifier IC that measures the voltage difference between two inputs while suppressing signals common to both inputs. This is the low-dropout regulator hierarchy's measurement counterpart: INA141 belongs to the amplifier IC category, where the precision instrumentation-amplifier subclass provides high input impedance, internally configured gain, and strong common-mode rejection. Unlike a general-purpose operational amplifier, the INA141 integrates a complete differential measurement stage, reducing external matching requirements in many sensor and bridge circuits.

The INA141 family supports two fixed-gain selections, G = 10 and G = 100, so engineers can choose between greater signal amplification and lower closed-loop bandwidth without changing the external gain-setting network. Its 1 MHz bandwidth supports moderate-frequency sensor signals. The listed 110 dB CMRR is particularly valuable when a small differential measurement is superimposed on a larger common-mode voltage, while the 8 nV/√Hz input-noise figure favors low-level instrumentation where source impedance is compatible with the input network.

The INA141UAG4 uses an internal differential amplifier arrangement to preserve common-mode rejection and gain accuracy across its operating range. It is offered in an 8-SOIC package, allowing conventional surface-mount assembly and PCB routing. Because the product is listed as inactive by DigiKey, engineers should treat it as a legacy design and verify lifecycle availability, supported package variants, and any migration path before starting a new production run.

Typical uses include bridge-transducer interfaces, pressure and strain measurements, current-shunt monitoring, and buffered sensing of low-amplitude differential signals. In these systems, the INA141 can amplify the difference between sensor lines while rejecting much of the common-mode voltage present on both lines. Its two gain choices are useful when a design must accommodate both relatively large and small differential signals without adding a programmable gain amplifier.

The principal design consideration is to verify input common-mode range, output swing, supply requirements, gain-dependent bandwidth, and input bias-current effects against the manufacturer datasheet for the exact operating condition. The 8-SOIC footprint should be routed with short, symmetric input paths and a clean ground return to minimize conversion of external noise into differential error. Decoupling should follow the manufacturer's recommended application circuit.

This product page combines the Texas Instruments product description with distributor lifecycle information and practical guidance for evaluating the INA141UAG4. It also identifies package-compatible alternatives and highlights the engineering differences that matter when an obsolete or inactive instrumentation amplifier must be replaced without changing the board layout.

ドロップイン代替品: INA141UAG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: INA141UAG4 (同一形状・フットプリント) — 相違点: Package, Amplifier Type, Supply Voltage Range.

Texas Instruments
Package: 8-pin SOIC
Amplifier Type: Instrumentation amplifier
Supply Voltage Range: ±18 V
比較対象 INA141UAG4 →
Texas Instruments
Package: 8-pin SOIC
Amplifier Type: Precision instrumentation amplifier
Supply Voltage Range: 2.25 V to 18 V
比較対象 INA141UAG4 →

INA141UA

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 8-SOIC
Instrumentation amplifier · Three-op-amp design · 1 circuit · 10 V/V or 100 V/V · 200 kHz · 50 µV · 0.5 µV/°C · 5 nA

価格はお問い合わせください

データシートを見る →

INA141UAE4

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 8-SOIC
Precision instrumentation amplifier · Three-op-amp design · 10 V/V · 100 V/V · 2.25 V to 18 V · 250 V · 200 kHz · 4 V/µs

価格はお問い合わせください

データシートを見る →

INA141UR

✅ ドロップイン ⚠️ 仕様未検証
📦 8-SOIC
8/8-pin package compatibility; R-grade supply or temperature differences are not quantified in the available comparison data

📋 参考代替品(カタログ未掲載)

INA141U/2K5

✅ ドロップイン
📦 8-SOIC
8/8-pin package compatibility; 2K5 identifies tape-and-reel packing rather than an electrical improvement

📋 参考代替品(カタログ未掲載)

AD621ARZ

✅ ドロップイン
Analog Devices
📦 8-SOIC
Single-channel instrumentation amplifier · 1 circuit · 800 kHz · 1.2 V/us · 500 pA · 75 uV · Up to +/-18 V · 8-pin SOIC

価格はお問い合わせください

データシートを見る →

INA141UAG4 最大定格&電気的特性

Product Type Precision low-power instrumentation amplifier
Amplifier Count 3 amplifiers
Gain 10 or 100
Bandwidth 1 MHz
Common-Mode Rejection Ratio 110 dB
Input Offset Voltage 20 µV
Input Offset Voltage, Datasheet Listing 250 µV
Input Noise Density 8 nV/√Hz
出力タイプ Single-ended
パッケージ 8-SOIC, 0.154 inch body width, 3.90 mm width
実装タイプ Surface mount

INA141UAG4 8-soic, 0.154 inch body width, 3.90 mm width ピン配置ガイド

INA141UAG4 (8-soic, 0.154 inch body width, 3.90 mm width パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

INA141UAG4 の 8-soic, 0.154 inch body width, 3.90 mm width パッケージピン配置図

詳細なピン配置データはありません: INA141UAG4.

詳細は データシート をご参照ください。

主な用途

INA141UAG4 の用途: 6 件s: Bridge Transducer Measurement, Strain-Gauge Signal Conditioning, Precision Current-Shunt Monitoring, Industrial Pressure Sensor Interface, Medical and Diagnostic Signal Conditioning, Low-Level Analog Sensor Interface.

🏭

Bridge Transducer Measurement

The INA141UAG4 fits bridge-transducer front ends that require a small differential output to be amplified while voltage shared by both sensor inputs is rejected. Its fixed gains of 10 and 100 allow the same amplifier family to cover different bridge sensitivities, and the listed 1 MHz bandwidth is suitable for moderate-frequency measurement channels. The listed 110 dB CMRR can reduce errors from common supply or ground disturbances encountered in sensor systems. Place the amplifier close to the bridge inputs, maintain symmetrical routing, and verify that bridge excitation, input common-mode voltage, and output swing remain inside the manufacturer limits.

🏭

Strain-Gauge Signal Conditioning

INA141UAG4 is appropriate for strain-gauge conditioning where a mechanical element generates a small differential voltage across bridge arms. The available gain choices of 10 and 100 provide useful scaling without an external gain-setting resistor, while the 8 nV/√Hz listed input-noise density supports low-level signal work. The 1 MHz bandwidth accommodates sensor dynamics beyond static resistance measurement, subject to the gain-specific response in the manufacturer datasheet. Short input traces, guard grounding, and a low-noise excitation source are important because they directly affect the integrity of the small differential signal.

⚡

Precision Current-Shunt Monitoring

The INA141UAG4 can monitor a current shunt when the shunt voltage is small and the measurement must reject voltage common to both sides of the shunt. A gain of 10 or 100 increases the useful output range without requiring an adjustable gain stage, and the listed 110 dB CMRR helps preserve measurement accuracy in systems with ground offsets or shared supply noise. The amplifier should be positioned so its input loop remains small, with Kelvin-style routing where practical. Confirm that the shunt common-mode voltage does not exceed the INA141 input range and that the output remains within the supply rails.

🏭

Industrial Pressure Sensor Interface

INA141UAG4 is suitable for conditioning the output of pressure, force, and displacement sensors that produce low-level differential signals in industrial environments. Fixed gains of 10 and 100 simplify analog scaling, and the 1 MHz bandwidth provides margin for sensor and filtering requirements beyond a purely static measurement. The single-ended output can feed a downstream data converter or control-system input. The design must remain within the device's supply, common-mode, and output-swing limits, while PCB isolation should prevent motor, relay, and switching-supply noise from entering the sensitive input path.

💊

Medical and Diagnostic Signal Conditioning

INA141UAG4 can serve as the analog front end of a low-level diagnostic or physiological measurement channel when its input range, offset, noise, and bandwidth satisfy the system requirements. The listed 20 µV typical offset and 8 nV/√Hz noise density are useful for small-signal conditioning, while 110 dB CMRR helps reject common-mode voltage on patient or sensor connections. A medical design must additionally evaluate isolation, leakage, safety, and application-specific standards; this IC alone does not provide those protections. Use the manufacturer datasheet to establish the achievable accuracy and configure gain and filtering accordingly.

🔧

Low-Level Analog Sensor Interface

INA141UAG4 fits generic analog sensor interfaces where the transducer produces a differential voltage and the next circuit requires a scaled, single-ended signal. Gain selections of 10 and 100 offer two useful sensitivity ranges, and the 1 MHz bandwidth permits filtering or modulation beyond DC. The amplifier reduces the number of external gain-setting components compared with a discrete three-op-amp implementation. For reliable operation, verify source impedance, input bias-current error, common-mode limits, output swing, and supply noise. Place decoupling capacitors close to the device and keep the sensitive input path physically separate from switching nodes and high-current returns.

おすすめ製品の概要

INA141UA Texas Instruments 使用用途: Bridge Transducer Measurement, Strain-Gauge Signal Conditioning, Industrial Pressure Sensor Interface, Medical and Diagnostic Signal Conditioning AD621ARZ 8-SOIC instrumentation-amplifier alternative 使用用途: Bridge Transducer Measurement, Precision Current-Shunt Monitoring, Medical and Diagnostic Signal Conditioning INA141UAE4 Texas Instruments 使用用途: Strain-Gauge Signal Conditioning, Industrial Pressure Sensor Interface INA141UR Same-family 8-SOIC replacement candidate 使用用途: Precision Current-Shunt Monitoring, Low-Level Analog Sensor Interface INA141U/2K5 Same-device 8-SOIC ordering option 使用用途: Low-Level Analog Sensor Interface
What is the INA141UAG4?
The INA141UAG4 is a Texas Instruments precision, low-power instrumentation amplifier in an 8-SOIC package. According to the Texas Instruments INA141 product information, it provides fixed gains of 10 and 100, a bandwidth of 1 MHz, and is intended for low-level differential-signal measurement. Its instrumentation-amplifier configuration integrates the functions normally required to amplify a differential sensor signal while rejecting common-mode noise.
What are the key specifications of INA141UAG4 that engineers should know?
The principal INA141UAG4 specifications are fixed gains of 10 or 100, 1 MHz bandwidth, 110 dB CMRR, 20 µV typical input offset voltage, and 8 nV/√Hz input-noise density, as listed by Texas Instruments and the manufacturer product listings. It is packaged in an 8-SOIC and provides a single-ended output. The UAG4 ordering code denotes the specific package, grade, and operating-temperature configuration.
What is the bandwidth of INA141UAG4?
The INA141UAG4 has a listed bandwidth of 1 MHz. According to the Texas Instruments INA141 product page, the device is a precision instrumentation amplifier with fixed gains of 10 and 100. Bandwidth differs between the two gain settings, so designers should consult the manufacturer datasheet for the gain-dependent frequency response before assuming that full operation is possible at 1 MHz.
What is the common-mode rejection ratio of INA141UAG4?
The listed common-mode rejection ratio of INA141UAG4 is 110 dB. According to Texas Instruments product information, this high CMRR helps the amplifier distinguish a small differential input from voltage shared by both input terminals. CMRR performance is frequency-dependent, so the datasheet curve should be checked for the signal bandwidth and common-mode range required by the application.
What is the input noise of INA141UAG4?
The listed input-referred noise density of INA141UAG4 is 8 nV/√Hz. According to the Texas Instruments product description, this low-noise figure supports precision instrumentation and small-signal measurement. Actual system noise also depends on source resistance, gain setting, amplifier bandwidth, and the noise contributed by adjacent input and reference components, so those parameters must be included in the complete noise budget.
What is the input offset voltage of INA141UAG4?
The manufacturer product information lists the INA141UAG4 input offset voltage as 20 µV, while one distributor datasheet index reports 250 µV. According to the Texas Instruments INA141 documentation, the relevant value depends on the gain configuration and test conditions. Use the exact gain and supply conditions from the manufacturer datasheet for error calculations rather than treating the two listed figures as directly interchangeable.
Where can I download the INA141UAG4 datasheet PDF?
The official INA141UAG4 documentation is available through the Texas Instruments INA141 product page at https://www.ti.com/product/INA141. Select the INA141 family datasheet link from the product documentation area. The UAG4 ordering information should also be checked to confirm the applicable package, temperature grade, and electrical limits for the exact device.
Where can I find the INA141UAG4 pinout?
The INA141UAG4 pinout is shown in the manufacturer INA141 datasheet available from the Texas Instruments product page. The device uses an 8-SOIC footprint, so the diagram should be compared directly with the PCB land pattern before assembly. Use the pin-description table for input, output, supply, reference, and resistor connections rather than inferring assignments from a generic SOIC drawing.
Is INA141UAG4 suitable for bridge and strain-gauge measurements?
Yes, INA141UAG4 is suitable for many bridge and strain-gauge measurement front ends because it offers fixed gains of 10 or 100, 1 MHz bandwidth, and 110 dB listed CMRR. The Texas Instruments product positioning identifies precision instrumentation as its target use. Input common-mode range, output swing, bridge excitation, and gain-induced bandwidth must still satisfy the sensor signal before the amplifier is approved.
What can replace INA141UAG4?
The closest replacements are pin-compatible 8-SOIC instrumentation amplifiers with gains that cover the 10 and 100 operating modes of the INA141UAG4. The identified comparison candidates include INA141UA, INA141UAE4, INA141UR, and AD621ARZ. Before replacement, verify supply range, common-mode range, output swing, gain accuracy, bandwidth, reference behavior, and exact PCB pin assignments.
Is INA141UA the same as INA141UAG4?
INA141UA and INA141UAG4 are both associated with the same Texas Instruments INA141 family and 8-SOIC package, but their ordering suffixes may specify different grade or operating conditions. According to the manufacturer family information, the core device provides gains of 10 and 100. Confirm the suffix-specific temperature range and limits in the TI ordering information before treating the two MPNs as equivalent.
Is AD621ARZ a drop-in replacement for INA141UAG4?
AD621ARZ is a possible 8-SOIC instrumentation-amplifier alternative for designs using compatible gain and signal-range conditions, but it should not be accepted as a drop-in replacement without detailed review. The identified cross-reference information identifies the device as an instrumentation amplifier, while the INA141UAG4 uses gains of 10 and 100. Verify gain-set behavior, supply voltage, common-mode range, output swing, bandwidth, reference implementation, and pin behavior.
When should I choose INA141UAG4 over another instrumentation amplifier?
Choose INA141UAG4 when an existing design specifically uses its 8-SOIC footprint, fixed gain of 10 or 100, 1 MHz-class bandwidth, and listed 110 dB CMRR. According to the Texas Instruments product page, it is optimized for precision, low-power instrumentation. A different amplifier is preferable when adjustable gain, rail-to-rail inputs, wider supply range, lower offset, or newer lifecycle status is required.
Where can I buy INA141UAG4 and what is its lead time?
Use the Request a Quote form on this page to ask for INA141UAG4 availability, unit pricing, minimum order quantity, and lead time for the required quantity and package. The component is marked inactive in distributor records, so current supply may be limited. The Request a Quote form allows the buyer to confirm whether an exact-match lot is available before placing an order.
Is INA141UAG4 currently active or obsolete?
The INA141UAG4 is treated as obsolete for this product record because DigiKey identifies the exact ordering code as inactive, while Texas Instruments continues to present the INA141 family product page. According to the Texas Instruments product information, the family includes precision, low-power instrumentation amplifiers with gains of 10 and 100. Confirm current orderability and any migration notice before beginning a new design.

エンジニアリング参考データ: INA141UAG4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the INA141UAG4 when maintaining an existing 8-SOIC design that requires the documented INA141 gain selections of 10 or 100, a listed 1 MHz bandwidth, 110 dB CMRR, and single-ended output. INA141UA and the suffix-specific INA141 family options are the first choices to examine because they retain the same package and measurement architecture; however, temperature grade, supply limits, and exact pin configuration must be checked. INA141U/2K5 primarily changes reel packing rather than the core device. Consider AD621ARZ only when its gain set, common-mode range, output swing, bandwidth, and reference behavior fit the circuit. For new designs, favor an actively supported instrumentation amplifier unless preserving the INA141 footprint outweighs the loss of lifecycle assurance.

代替品との比較

パラメータ この製品 INA141UA INA141UAE4 INA141UR INA141U/2K5 AD621ARZ
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices
Product Type Precision low-power instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Instrumentation amplifier

主な差別化要因

  • Two integrated fixed-gain choices simplify sensor scaling (vs AD621ARZ)
  • Strong common-mode rejection for differential sensing (vs AD621ARZ)
  • Low-noise input suitable for precision instrumentation (vs INA141UA)

設計ノート

Route the two differential inputs as a short, closely coupled pair and connect their return path to the quiet analog ground associated with the sensor. Minimize loop area because magnetic and capacitive coupling can appear directly as differential error. Keep the INA141UAG4 away from switching-node copper, high-current relay paths, and isolated power-converter returns. The manufacturer pin-description table should be used when assigning the eight SOIC pads.

Design the analog filter around the selected fixed gain rather than assuming one bandwidth applies to both G = 10 and G = 100. The family is listed with 1 MHz bandwidth, but the gain-dependent response, output settling, and common-mode rejection vary with frequency. Confirm those curves in the INA141 datasheet, then place any additional input or output filtering close to the corresponding pins to avoid adding board-level noise pickup.

Do not treat the INA141UAG4 as a general-purpose rail-to-rail operational amplifier. Its input common-mode range, output swing, supply range, and reference connections must be checked at the exact signal extremes and gain setting. The two distributor indexes also present different offset-voltage figures, so use the gain-specific manufacturer test condition for error budgets rather than copying an isolated headline number into a precision calculation.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact INA141UAG4 ordering code.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

INA141UAG4 datasheet INA141UAG4 pinout INA141UAG4 datasheet pdf INA141UAG4 specifications INA141UAG4 equivalent INA141UAG4 replacement INA141UAG4 cross reference INA141UAG4 8-SOIC INA141UAG4 1 MHz amplifier INA141UAG4 bridge sensor INA141UAG4 vs AD621ARZ INA141UAG4 price INA141UAG4 stock Texas Instruments INA141UAG4

関連部品&用語

Texas Instruments INA141UAG4 INA141UA INA141UAE4 INA141UR INA141U/2K5 AD621ARZ Analog Devices instrumentation amplifier precision amplifier amplifier IC semiconductor differential signal common-mode rejection ratio CMRR input offset voltage input noise density gain bandwidth single-ended output 8-SOIC SOIC family surface-mount package bridge transducer strain gauge
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示