Texas Instruments

INA2141UG4 - Dual 10/100 Gain Instrumentation Amp | TI

部品番号: INA2141UG4 ✓ 生産中
15 mA Vdss 5 nA Id 16-pin SOIC, 300 mil Package
MOQ: 1 |

INA2141UG4 概要

The Texas Instruments INA2141UG4 is a dual, low-power instrumentation amplifier with selectable gains of 10 or 100, a 200 kHz bandwidth at gain 100, and a 16-pin SOIC package. Each amplifier provides one instrumentation-amplifier channel, allowing two independent differential measurements in a compact surface-mount design.

An instrumentation amplifier is a precision analog circuit that amplifies the voltage difference between two inputs while rejecting common-mode signals. The INA2141 belongs to the instrumentation-amplifier hierarchy within amplifier ICs and analog signal-chain conditioning. Its internal three-op-amp architecture supports current-feedback input circuitry, preserving useful bandwidth at high gain and simplifying front-end design for bridge sensors, low-voltage sensing, and industrial measurement systems.

Key characteristics include two amplifiers per package, gain options of 10 and 100, 200 kHz bandwidth at a gain of 100, and a typical signal-to-noise ratio listed at 117 dB. The operating temperature range extends from -40 °C to +85 °C. The gain-setting arrangement eliminates the need for external feedback resistors, while the integrated input circuitry reduces component count and makes the device suitable for compact, high-impedance sensing nodes.

Technically, the INA2141 combines differential input handling with internal feedback networks and an output amplifier in each channel. Current-feedback input circuitry is the key bandwidth feature: the specified 200 kHz gain-bandwidth behavior at gain 100 supports faster signal capture than a typical low-frequency precision-only instrumentation amplifier. The device operates from a 5 V supply and consumes approximately 15 mA, balancing channel density, measurement bandwidth, and power consumption for portable and industrial equipment.

Typical uses include precision bridge excitation for pressure and load cells, current-sense amplification in power systems, battery and energy monitoring, biomedical instrumentation interfaces, and factory sensor acquisition. In bridge-based measurements, the amplifier rejects supply and ground disturbances shared by both sensor inputs. In current sensing, it magnifies a small differential shunt voltage while limiting the influence of common supply variation.

A critical design consideration is input and output range: the selected gain and 5 V supply determine the usable differential and output spans. Review the absolute maximum and recommended operating conditions in the manufacturer datasheet before applying large bridge or shunt inputs. PCB placement should keep sensitive input traces short, provide a stable reference or return path, and separate analog routing from switching-converter and digital timing nodes.

This page combines manufacturer electrical characteristics, package and ordering information, sourced pricing, drop-in replacement guidance, and application-focused engineering guidance. It is intended to help engineers evaluate the INA2141UG4 for precision differential measurement while identifying the key electrical and layout checks required before release to production.

ドロップイン代替品: INA2141UG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: INA2141UG4 (同一形状・フットプリント) — 相違点: Input Bias Current, Input Offset Voltage Drift, Package, Slew Rate.

Texas Instruments
Input Bias Current: 5 nA maximum
Input Offset Voltage Drift: 0.5 µV/°C maximum
Package: 16-pin SOIC (DW)
比較対象 INA2141UG4 →

INA2141U

✅ ドロップイン
Texas Instruments
📦 16-pin SOIC
2 channels · Dual instrumentation amplifier · 10 or 100 · 1 MHz · 4 V/µs · 50 µV maximum · 0.5 µV/°C maximum · ±0.05% maximum

価格はお問い合わせください

データシートを見る →

INA2141UE4

✅ ドロップイン
📦 16-pin SOIC
Ordering suffix differs; the 16-pin SOIC pinout and core dual-channel 10/100-gain performance remain equivalent.

📋 参考代替品(カタログ未掲載)

INA2141UG4 最大定格&電気的特性

Product Type Dual instrumentation amplifier
Number of Channels 2 channels
Amplifier Architecture 3-op-amp instrumentation amplifier per channel
Gain Options 10 or 100 V/V
Bandwidth at Gain 100 200 kHz
Signal-to-Noise Ratio 117 dB
電源電流 15 mA
Slew Rate 1 V/us
Input Offset Voltage Drift 500 nV/°C
Maximum Output Error 50 uV
Input Bias Current 5 nA
Output Current 750 uA
電源電圧 5 V
動作温度範囲 -40 °C to +85 °C
パッケージ 16-pin SOIC, 300 mil
実装タイプ Surface mount
RoHS ステータス Compliant
Gain Resistors Integrated; external feedback resistors not required
Input Circuitry Current-feedback

INA2141UG4 16-pin soic, 300 mil ピン配置ガイド

INA2141UG4 (16-pin soic, 300 mil パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

INA2141UG4 の 16-pin soic, 300 mil パッケージピン配置図

詳細なピン配置データはありません: INA2141UG4.

詳細は データシート をご参照ください。

主な用途

INA2141UG4 の用途: 6 件s: Pressure and Load-Cell Bridge Sensing, Battery and Power-Current Monitoring, Industrial Sensor Signal Conditioning, Medical and Biosignal Instrumentation, Portable Instrument and Test Equipment, Precision Feedback and Control Loops.

🏭

Pressure and Load-Cell Bridge Sensing

The INA2141UG4 fits dual-channel bridge sensing because each channel amplifies the small differential voltage generated by a resistive load cell while rejecting voltage common to both inputs. Its internal gains of 10 or 100 avoid external feedback resistors, and the 200 kHz bandwidth at gain 100 supports faster force or pressure changes. Two channels can monitor independent axes in a multi-axis sensor. The main design limit is the allowable input common-mode range and output swing, which must remain within the 5 V supply and the datasheet limits.

⚡

Battery and Power-Current Monitoring

The INA2141UG4 can amplify the differential voltage across a low-ohm shunt in a battery-management or power-conversion system. Gain 10 is useful for larger shunt signals, while gain 100 increases sensitivity to smaller voltage drops. Its common-mode rejection helps prevent supply ripple and ground offsets from appearing at the output. Two independent channels can monitor input and output current simultaneously. Designers should verify the shunt common-mode voltage, output swing, and amplifier stability for the selected gain.

⚙️

Industrial Sensor Signal Conditioning

The INA2141UG4 is suitable for conditioning low-level industrial sensor outputs before digitization or control. The dual architecture reduces the component count when two transducers must be measured, and the integrated 10 and 100 gain choices simplify front-end configuration. Current-feedback input circuitry provides 200 kHz bandwidth at gain 100 for moderate-speed process signals. Layout should keep input traces short and isolated from switching nodes, while the reference input must be driven appropriately when a nonzero output offset is required.

💊

Medical and Biosignal Instrumentation

The INA2141UG4 can serve as the first analog stage in medical or biosignal instrumentation when the sensor output is differential and the system requires two measurement channels. Instrumentation-amplifier topology suppresses common-mode interference, while the 10 and 100 gain settings support different transducer sensitivities. The 16-pin SOIC format allows compact board placement, and 200 kHz bandwidth at gain 100 accommodates more demanding physiological signals. Safety, input protection, patient isolation, and application-specific standards require separate system-level validation.

🖥️

Portable Instrument and Test Equipment

The INA2141UG4 is appropriate for portable measurement equipment where two precision channels must fit in a compact area without a large external resistor network. Operation from a 5 V rail and approximately 15 mA supply current supports power-constrained instruments, while the internal gain options simplify calibration. The 200 kHz bandwidth at gain 100 allows measurement of moderately fast events rather than only static voltages. Care should be taken to avoid input overload and to preserve common-mode headroom during battery changes.

🔧

Precision Feedback and Control Loops

The INA2141UG4 can condition differential feedback signals in precision analog control systems, particularly when the controller benefits from rejection of shared supply or ground disturbances. Gain 100 increases small error-signal sensitivity while retaining 200 kHz bandwidth, making it useful in current-feedback control architectures. The two channels can form matched signal paths for differential sensing. Stable operation depends on keeping the common-mode and differential inputs inside the specified range, providing a clean reference connection, and avoiding excessive output loading.

What is the INA2141UG4?
The INA2141UG4 is a dual, low-power instrumentation amplifier with two independent amplifier channels, selectable gains of 10 or 100, and a 16-pin SOIC package. According to the Texas Instruments INA2141 datasheet, each channel uses a three-op-amp architecture with current-feedback input circuitry, providing 200 kHz bandwidth at a gain of 100 while accepting low-level differential signals with high common-mode rejection.
What is the operating voltage of INA2141UG4?
The INA2141UG4 operates from a single 5 V supply. The Texas Instruments INA2141 datasheet identifies a typical supply current of approximately 15 mA and a temperature range of -40 °C to +85 °C. Because the device amplifies a differential signal, engineers should also verify the input common-mode range and output swing in the datasheet before operating near the supply rails.
What gain settings does INA2141UG4 support?
The INA2141UG4 supports gains of 10 and 100. According to the Texas Instruments INA2141 datasheet, the gain is selected internally, eliminating external gain-setting resistors and reducing component count. The gain-100 configuration provides 200 kHz bandwidth, making the amplifier suitable for higher-speed differential sensor signals than applications requiring only the lower gain setting.
Where can I download the INA2141UG4 datasheet PDF?
The official INA2141UG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina2141.pdf. It documents the dual-channel architecture, gain settings, electrical characteristics, input and output limits, pin descriptions, and typical application circuits. The manufacturer product page at https://www.ti.com/product/INA2141 provides ordering options, parameter filters, and product support information.
Where can I find the INA2141UG4 pinout?
The INA2141UG4 pin assignment is shown in the pin-configuration section of the Texas Instruments INA2141 datasheet. The device uses a 16-pin SOIC package and contains two instrumentation-amplifier channels. Use that pin table when assigning supply, ground, differential inputs, reference connections, and outputs because the SOIC has no exposed thermal pad and each channel includes a reference input.
What can replace INA2141UG4?
INA2141U and INA2141UE4 are documented pin-compatible alternatives to INA2141UG4, with the same 16-pin SOIC footprint, two channels, 10 or 100 gain settings, and 200 kHz bandwidth at gain 100. The distinction is primarily the ordering and packaging suffix. Confirm the ordering suffix, temperature grade, marking, and manufacturer product documentation before production substitution.
Is INA2141U the same as INA2141UG4?
INA2141U is functionally and pin compatible with INA2141UG4 according to the available cross-reference information. Both use a 16-pin SOIC package and provide two instrumentation-amplifier channels with 10 or 100 gain settings and 200 kHz bandwidth at gain 100. Treat the ordering suffix as an ordering and marking distinction, and verify the exact orderable part status before approving a substitution.
Is INA2141UG4 suitable for bridge sensor measurements?
The INA2141UG4 is suitable for low-level bridge measurements when its common-mode and output ranges remain inside the device limits. Its internal gain settings remove external feedback resistors, while the instrumentation-amplifier topology rejects common-mode voltage present equally on both sensor inputs. Texas Instruments identifies the INA2141 as suitable for instrumentation and sensor-interface applications, including precision bridge sensing.
What is the bandwidth of INA2141UG4 at gain 100?
The INA2141UG4 provides 200 kHz bandwidth at a gain of 100. Texas Instruments states this value in the INA2141 datasheet and attributes the performance to the current-feedback input circuitry. This makes the device suitable for differential signals requiring more bandwidth than a slow precision-only amplifier, while the internal gain options keep the external circuit simple.
Where to buy INA2141UG4 online?
Use the Request a Quote form on this page to request INA2141UG4 availability, lead time, and order quantities from XAIPART. The part is identified as a Texas Instruments 16-pin SOIC instrumentation amplifier, and its manufacturer documentation is linked on this page. The quote form is the appropriate route for current sourcing, schedule, and quantity commitments.
What is the price of INA2141UG4?
Use the Request a Quote form on this page for the current INA2141UG4 price and quantity schedule. Pricing can vary with order quantity, sourcing condition, and market availability, so a static price should not be used for budgeting. The part number, manufacturer, package, and lifecycle information shown on this page can be included with the request for a faster quotation.
What is the lead time for INA2141UG4?
Request the current INA2141UG4 lead time through the Request a Quote form on this page. Lead time depends on the required quantity, package variant, stock position, and production schedule. The manufacturer product page lists the INA2141 family and ordering information, while the quote form is the correct route for a committed delivery estimate.
Is INA2141UG4 in stock?
Current INA2141UG4 stock status should be confirmed through the Request a Quote form on this page. The Texas Instruments product page identifies the INA2141 family, but real-time inventory and order schedules can change independently of product lifecycle status. Submit the required quantity and target package information with the request to obtain an availability confirmation.
INA2141UG4 vs INA2141U — which is better?
INA2141U and INA2141UG4 provide the same core instrumentation-amplifier functionality: two channels, 10 or 100 gain settings, and 200 kHz bandwidth at gain 100 in a 16-pin SOIC package. Choose according to the approved manufacturer ordering suffix, supply-chain status, temperature grade, and traceability requirements rather than basic signal-processing performance.
When should I choose INA2141UG4 over INA2141UE4?
Choose INA2141UG4 when its ordering suffix matches the component already qualified in your BOM, while INA2141UE4 is appropriate when its ordering code is approved for the same 16-pin SOIC footprint. Both offer two channels, gains of 10 and 100, and 200 kHz bandwidth at gain 100. Confirm lifecycle, date codes, marking, and any qualification requirements before changing an approved part.
What are the key specifications of INA2141UG4 that engineers should know?
The key INA2141UG4 specifications are two channels, internal gains of 10 or 100, 200 kHz bandwidth at gain 100, 5 V operation, approximately 15 mA supply current, a -40 °C to +85 °C temperature range, and a 16-pin SOIC package. According to the Texas Instruments datasheet, current-feedback input circuitry preserves bandwidth at gain 100 while integrated gain resistors simplify the analog front end.
What is the best cross-brand equivalent for INA2141UG4?
No cross-brand drop-in equivalent is established in the available component cross-reference information for INA2141UG4. A valid replacement must match the 16-pin SOIC footprint, pin functions, 10 or 100 gain architecture, supply range, input and output ranges, bandwidth, and precision requirements. A merely similar instrumentation amplifier should not be treated as a drop-in part without a manufacturer-documented pin and parameter comparison.

エンジニアリング参考データ: INA2141UG4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose INA2141UG4 when the approved BOM calls for a dual, 5 V instrumentation amplifier with internal gains of 10 and 100 in a 16-pin SOIC package. Its 200 kHz bandwidth at gain 100 supports differential sensors and shunt measurements that need more speed than a static precision amplifier. Choose INA2141U when that ordering suffix is the preferred Texas Instruments catalog option for the same electrical configuration and footprint. Choose INA2141UE4 when its ordering code satisfies procurement and qualification requirements. These alternatives provide the same two-channel architecture, gain selections, and 16-pin pinout, but engineers should still verify lifecycle status, date-code rules, marking, and temperature requirements. No cross-brand part should be treated as a drop-in replacement without a documented comparison of every pin, the supply range, common-mode range, output swing, gain accuracy, bandwidth, and stability.

代替品との比較

パラメータ この製品 INA2141U INA2141UE4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC
Number of Channels 2 2 2
Gain Settings 10 or 100 V/V 10 or 100 V/V 10 or 100 V/V
Bandwidth at Gain 100 200 kHz 200 kHz 200 kHz
Supply Voltage 5 V 5 V 5 V
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C -40 °C to +85 °C
Input Architecture Current-feedback Current-feedback Current-feedback

主な差別化要因

  • Two instrumentation-amplifier channels in one package (vs INA2141U)
  • Wide bandwidth retained at the higher internal gain (vs INA2141UE4)
  • Compact 16-pin SOIC implementation (vs INA2141U)

設計ノート

Route both inputs of each differential channel as closely matched, short traces as practical. Keep input nodes away from switching-regulator outputs, relay contacts, motor traces, and high-current return paths. The reference input should have a low-impedance local return path, and unused channel inputs should be connected according to the manufacturer recommendations rather than left floating.

Estimated supply-current draw is approximately 15 mA at the specified 5 V operating condition. Estimated power dissipation using an input of 5 V, output of 3.3 V, and 15 mA current is (5 V - 3.3 V) × 0.015 A = 0.0255 W. Confirm actual channel loading, supply tolerance, and regulator headroom in the finished design rather than using this estimate as a worst-case thermal rating.

Do not select the gain solely from signal amplitude. First confirm that the input common-mode voltage remains inside the operating range, then verify that the multiplied differential signal and reference offset can swing within the output limits. Overload, common-mode clipping, and output saturation produce different symptoms and require different corrections.

For gain 100, preserve the 200 kHz bandwidth capability by minimizing parasitic capacitance on the input and output nodes and placing any required output filtering close to the amplifier. Input shielding or guarding may be necessary for very high source impedances, while solid reference grounding helps suppress common-mode and ground-induced errors.

コンプライアンス情報

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The component listing identifies the INA2141UG4 as RoHS compliant. No specific REACH, halogen-free, conflict-minerals, or automotive qualification statement is published in the cited product information.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

INA2141UG4 datasheet INA2141UG4 pinout INA2141UG4 datasheet pdf INA2141UG4 equivalent INA2141UG4 replacement INA2141UG4 drop-in replacement INA2141UG4 vs INA2141U INA2141UG4 price INA2141UG4 stock Texas Instruments INA2141UG4 INA2141UG4 16-SOIC amplifier INA2141UG4 bridge sensor amplifier

関連部品&用語

Texas Instruments INA2141UG4 INA2141U INA2141UE4 instrumentation amplifier precision analog amplifier amplifier IC dual amplifier three-op-amp architecture current-feedback input differential input common-mode rejection gain 10 gain 100 200 kHz bandwidth 5 V supply 15 mA supply current 117 dB signal-to-noise ratio 16-pin SOIC surface-mount package load-cell bridge shunt current sensing industrial sensor conditioning RoHS
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示