ISL8488IPZ - 5V RS-485/RS-422 Transceiver | Renesas
部品番号: ISL8488IPZ ✗ 生産終了ISL8488IPZ 概要
A differential transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable transmission over cables. An RS-422 interface generally supports a driver-to-receiver topology, while RS-485 allows multiple drivers and receivers to share a bus when only one device drives at a time. The ISL8488IPZ belongs to the broader hierarchy of interface IC, communication transceiver, line transceiver, and data-conversion semiconductor.
The ISL8488IPZ is identified as a low-power, high-speed or slew-rate-limited RS-485/RS-422 transceiver. These features suit industrial equipment, instrumentation, data acquisition, and embedded systems that require balanced differential signaling over cable distances. Its single-driver, single-receiver organization also allows one transceiver to provide both transmit and receive paths within a communications interface.
The 5 V supply operation integrates with conventional embedded and industrial control systems. Differential signaling improves noise immunity by receiving the difference between two conductors rather than relying on a single signal referenced to ground. This characteristic is valuable in environments containing motors, relays, switching converters, and other sources of electrical interference.
Typical applications include industrial monitoring, test equipment, remote sensor interfaces, building controls, factory automation, and embedded serial links. In a multidrop RS-485 installation, the transceiver can communicate over a shared pair of wires when the system controls which node transmits. In RS-422 installations, separate differential pairs are commonly used for full-duplex communication.
When laying out the board, keep the transceiver close to the connector and cable interface, provide a solid ground reference, and follow the manufacturer datasheet for termination and biasing arrangements. The exact drive-strength, receive-threshold, slew-rate, and temperature limits should be confirmed from the device electrical characteristics before fixing maximum bus length or data rate.
This page organizes the ISL8488IPZ product information with interface-specific application guidance, package details, sourcing questions, and verified drop-in comparison candidates. It also highlights the design checks that matter when replacing a transceiver in an existing RS-485 or RS-422 PCB.
ドロップイン代替品: ISL8488IPZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ISL8488IPZ (同一形状・フットプリント) — 相違点: Package, Product Type, Supported Standards, Mounting Type, Maximum Data Rate.
ISL8487IPZ
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →ISL8486IPZ
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
ISL8489IPZ
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
ISL8485IPZ
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →ISL8488IPZ 仕様
| Product Type | RS-485/RS-422 differential line transceiver |
| 電源電圧 | 5 V |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| Supported Standards | RS-422 and RS-485 |
| パッケージ | 8-PDIP |
| ピン数 | 8 pins |
| 実装タイプ | Through-hole |
| Power Class | Low-power |
| Signal Type | Differential balanced |
ISL8488IPZ ピン構成
| ピン 1 | RO — Receiver output |
| ピン 2 | /RE — Active-low receiver enable input |
| ピン 3 | DE — Driver enable input |
| ピン 4 | DI — Driver data input |
| ピン 5 | GND — Ground reference |
| ピン 6 | A — Non-inverting differential bus terminal |
| ピン 7 | B — Inverting differential bus terminal |
| ピン 8 | VCC — 5 V supply connection |
主な用途
ISL8488IPZ の用途: 6 件s: Industrial Sensor Networking, Factory Automation Equipment, Test and Measurement Instruments, Building and HVAC Controls, Data Acquisition Systems, Embedded Communication Port.
Industrial Sensor Networking
The ISL8488IPZ fits industrial sensor networks that use a 5 V RS-485 bus for remote measurements. Its differential receiver rejects common-mode noise picked up between field wiring and the controller enclosure, while one transmitter and one receiver support a compact half-duplex interface. The device is placed between the host UART or processor I/O and a protected connector-side transceiver path. Designers should confirm data rate, common-mode limits, and thermal performance against the cable length and environmental conditions before using the ISL8488IPZ in a new controller.
おすすめ
Factory Automation Equipment
The ISL8488IPZ is useful in factory automation equipment that must exchange commands and status data with remote actuators, motion controllers, or operator panels. The 5 V supply supports conventional embedded power systems, and the RS-485/RS-422 interface provides a balanced path that is less susceptible to electrical noise than a single-ended serial link. One driver and one receiver can serve a multidrop half-duplex bus or separate full-duplex RS-422 pairs. The implementation must preserve the enable-control timing and manufacturer-recommended bus termination.
おすすめ
Test and Measurement Instruments
The ISL8488IPZ can connect laboratory and field-test instruments to remote fixtures over an RS-485 or RS-422 differential bus. The balanced interface reduces susceptibility to noise generated by adjacent test equipment, while the single-transmitter, single-receiver organization gives a straightforward way to implement half-duplex command and response traffic. Use the transceiver near the external connector to minimize exposed high-impedance paths, and verify that the selected slew rate and bus timing remain valid over the intended cable distance.
おすすめ
Building and HVAC Controls
The ISL8488IPZ is appropriate for building-control networks carrying sensor readings and actuator commands between distributed controllers. A 5 V RS-485 interface supports a balanced connection that is useful in buildings containing fluorescent lighting, motor drives, switching supplies, and long cable runs. The transceiver’s one-driver, one-receiver arrangement can support a multidrop bus when only one controller transmits at a time. Board designers should add the required protection network, maintain a continuous reference ground, and observe the manufacturer's enable and termination guidance.
おすすめ
Data Acquisition Systems
The ISL8488IPZ supports distributed data-acquisition systems where multiple measurement stations must forward results over a shared cable. Its differential RS-485 operation is well suited to electrically noisy environments because the receiver responds to the voltage difference across a pair rather than to a single conductor referenced to ground. A single transceiver pair provides both transmit and receive functions for half-duplex traffic. The bus should include the correct termination and biasing arrangement, and the selected data rate should be derated for cable length and node count.
おすすめ
Embedded Communication Port
The ISL8488IPZ provides a compact physical layer between an embedded processor UART and a balanced external bus. The 8-PDIP package is convenient for leaded industrial controller boards and legacy equipment where a surface-mount transceiver is not required. Driver-enable and receiver-enable inputs allow firmware or hardware to control bus direction, supporting half-duplex communication over one RS-485 pair. Because the transceiver is not a complete protocol controller, the embedded system must also handle framing, addressing, collision avoidance, and bus timing.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ISL8488IPZ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISL8487IPZ | ISL8486IPZ | ISL8489IPZ | ISL8485IPZ |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-PDIP | 8-PDIP - same | 8-PDIP - same | 8-PDIP - same | 8-PDIP - same |
| Transmitter Count | 1 | 1 | 1 | 1 | 1 |
| Receiver Count | 1 | 1 | 1 | 1 | 1 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Supported Interfaces | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Power Class | Low-power | Low-power | Low-power | Low-power | Low-power |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
主な差別化要因
- Combines RS-485 and RS-422 operation in one transceiver (vs MAX488ESA+)
- Through-hole package supports leaded industrial board layouts (vs MAX488ESA+)
- Same-family option retains 5 V single-driver, single-receiver organization (vs ISL8486IPZ)
設計ノート
Place the ISL8488IPZ close to the external connector and route the A and B differential pair as a tight, matched pair. Keep the transceiver-side ground reference continuous and return it through the cable shield or connector ground according to the installation architecture. Avoid sharing wide ground-current paths between the transceiver and switching circuitry because those currents can create differential noise even when the bus itself is balanced.
Do not substitute a family member solely because it has an 8-pin DIP outline. Compare data rate, slew rate, receiver thresholds, driver output limits, enable polarity, and common-mode range in the manufacturer electrical tables. The ISL8487IPZ, ISL8486IPZ, ISL8489IPZ, and ISL8485IPZ alternatives may change edge-rate or timing margins, which can invalidate a previously validated cable and topology.
Apply termination and fail-safe biasing at the physical ends of the bus rather than at every node. A multidrop RS-485 network normally uses termination at the two remote ends, while bias resistors establish the idle state at one suitable location. Confirm resistor values and enable polarity in the datasheet application circuit before applying them because incorrect biasing can increase common-mode current or prevent a receiver from detecting the idle state.
Decouple the 5 V transceiver supply locally with the capacitance and placement specified by the manufacturer application circuit. Keep switching-regulator and high-current return paths away from the A and B traces, and provide controlled rise time at enable pins to avoid unwanted bus transitions. These practices reduce false receiver activity and improve interoperability in systems where multiple nodes share the same cable.
コンプライアンス情報
The available catalog information identifies the device as a 5 V RS-485/RS-422 transceiver in an 8-PDIP package but does not state environmental or substance-compliance status.