SMSC Corporation

LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC

部品番号: LAN91C111I-NU-E2 ✓ 生産中
2.97 V to 3.63 V Vdss IEEE 802.3 and IEEE 802.3u Rds(on) 128-pin TQFP Package 10 Mbps and 100 Mbps Speed
MOQ: 1 |

LAN91C111I-NU-E2 概要

The SMSC Corporation LAN91C111I-NU-E2 is a single-chip 10/100 Ethernet controller with an integrated physical layer, parallel host interface, and non-PCI architecture, housed in a 128-pin TQFP package measuring 14 x 14 mm. It supports 10 Mbps and 100 Mbps Ethernet operation according to IEEE 802.3 and IEEE 802.3u, while operating from a 2.97 V to 3.63 V core supply.

An Ethernet controller is an interface integrated circuit that connects an embedded processing system to a physical Ethernet network. In the hierarchy, the LAN91C111 belongs to Ethernet controllers, interface ICs, integrated circuits, and semiconductors. Integrating the MAC and PHY reduces the number of components required for an embedded Fast Ethernet port, while the parallel interface provides direct access between the controller and external host-bus circuitry.

The LAN91C111 uses a four-bit Media Independent Interface for connections to either 10 Mbps or 100 Mbps Ethernet networks. Three device pins support the two-wire serial MII management protocol. This combination allows the controller to participate in MII-based network designs without requiring the parallel interface to be limited to one Ethernet speed. The controller is intended for embedded systems requiring dedicated Fast Ethernet connectivity rather than a PCI-based desktop adapter.

The device is identified as a 10/100 Base-T/TX PHY controller with a parallel host interface. Its 128-TQFP package provides the mixed-signal and digital connections needed for the MAC, PHY, host interface, and MII functions. Because it combines analog and digital circuitry on one device, PCB implementation requires controlled trace routing, suitable grounding, and careful separation of high-speed digital signals from sensitive network and clock connections.

Typical applications include embedded industrial controllers, test equipment, print servers, communications appliances, and other systems requiring a compact 10/100 Ethernet interface. The integrated MAC and PHY are especially useful when a system cannot accommodate a discrete Ethernet PHY or a separate PCI Ethernet controller. The parallel host interface must still be matched carefully to the target processor, bus logic, and firmware architecture.

When designing around the LAN91C111I-NU-E2, verify the host-bus timing, MII connections, magnetic-interface implementation, and available board area before releasing a PCB layout. The 128-pin package is not physically interchangeable with smaller Ethernet interfaces without a complete board redesign, so footprint and firmware compatibility are as important as nominal Ethernet performance.

This page combines the manufacturer interface information, package identification, ordering details, and engineering guidance for the LAN91C111I-NU-E2. It also documents the distinctions among related LAN91C111 ordering codes and provides practical considerations for evaluating this non-PCI Ethernet controller in an embedded Fast Ethernet design.

ドロップイン代替品: LAN91C111I-NU-E2 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: LAN91C111I-NU-E2 (同一形状・フットプリント) — 相違点: Host Interface, Package.

Microchip Technology
Host Interface: 8-bit, 16-bit, or 32-bit parallel bus
Package: 128-lead TQFP, 14 mm x 14 mm
比較対象 LAN91C111I-NU-E2 →

LAN91C111I-NU

✅ ドロップイン
📦 128-TQFP (14x14)
Same 10/100 MAC and PHY, parallel interface, voltage range, and 128-TQFP footprint; only the trailing E2 ordering treatment differs, pending order-code confirmation

📋 参考代替品(カタログ未掲載)

LAN91C111-NU

✅ ドロップイン
Microchip Technology
📦 128-TQFP (14x14)
10/100 non-PCI Ethernet single-chip MAC and PHY · 10 Mbps and 100 Mbps · 8-bit, 16-bit, or 32-bit parallel bus · 8 KB dynamically configurable TX/RX SRAM · 10/100 Base-T/TX · CSMA/CD · 3.3 V · 128-lead TQFP, 14 mm x 14 mm

価格はお問い合わせください

データシートを見る →

LAN91C111I-NU-E2 仕様

Product Type 10/100 Ethernet single-chip MAC and PHY controller
Ethernet Speed 10 Mbps and 100 Mbps
Host Interface Parallel interface
Bus Architecture Non-PCI
Media Interface 4-bit MII
MII Management Interface 2-wire serial protocol
Core Supply Voltage 2.97 V to 3.63 V
Ethernet Standards IEEE 802.3 and IEEE 802.3u
パッケージ 128-pin TQFP
Package Dimensions 14 x 14 mm
実装タイプ Surface mount
Temperature Grade Industrial temperature, indicated by I ordering code
Integrated Functions Ethernet MAC and PHY
Physical Layer 10/100 Base-T/TX PHY

LAN91C111I-NU-E2 14 x 14 mm ピン配置ガイド

LAN91C111I-NU-E2 (14 x 14 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

LAN91C111I-NU-E2 の 14 x 14 mm パッケージピン配置図

詳細なピン配置データはありません: LAN91C111I-NU-E2.

詳細は データシート をご参照ください。

主な用途

LAN91C111I-NU-E2 の用途: 6 件s: Embedded Industrial Ethernet Controller, Test and Measurement Ethernet Interface, Communications Gateway, Print Server and Network Appliance, Security and Surveillance Endpoint, Data Acquisition and Control Module.

🏭

Embedded Industrial Ethernet Controller

The LAN91C111I-NU-E2 fits an embedded industrial controller that needs both 10 Mbps and 100 Mbps Ethernet connectivity without adding a separate MAC and PHY. Its integrated 10/100 Base-T/TX physical layer and non-PCI architecture reduce the number of high-speed network components on the board. The parallel host interface can connect to suitable bus logic, while the four-bit MII provides a standardized route to the integrated PHY section. The principal design constraint is the 128-pin TQFP footprint, which requires adequate routing space and careful separation between host, clock, management, and analog network connections.

🔧

Test and Measurement Ethernet Interface

The LAN91C111I-NU-E2 can provide Fast Ethernet connectivity in test and measurement equipment that must transfer status, results, or configuration data over an embedded network. Supporting 10 Mbps and 100 Mbps allows interoperability with older management networks as well as faster local links. The integrated MAC and PHY simplifies the physical Ethernet portion of the design, but the parallel host interface still requires buffering or glue logic when the host processor does not expose the required bus protocol directly.

🌐

Communications Gateway

A communications gateway can use the LAN91C111I-NU-E2 to add a dedicated 10/100 Ethernet endpoint to an embedded control platform. The integrated MAC and PHY are useful when the gateway needs a second network function independent of a host-provided PCI or USB Ethernet interface. IEEE 802.3 and IEEE 802.3u operation supports common Fast Ethernet infrastructure. Designers should allocate the 128-pin TQFP footprint correctly and confirm that the processor-side bus timing and firmware driver can support the controller's parallel interface.

🖥️

Print Server and Network Appliance

The LAN91C111I-NU-E2 is suitable for legacy-style print servers and compact network appliances that require one 10/100 Ethernet port implemented with embedded silicon. Its single-chip MAC-and-PHY arrangement reduces board complexity compared with a split implementation, while the non-PCI architecture avoids requiring a desktop peripheral bus. The 128-pin package still demands a larger PCB area than modern highly integrated Ethernet PHYs, so the controller is most attractive where its established software support and legacy host interface are more valuable than minimal footprint.

🎥

Security and Surveillance Endpoint

The LAN91C111I-NU-E2 can support a compact security or surveillance endpoint that exchanges configuration data and status over 10/100 Ethernet. The integrated physical layer avoids a separate Ethernet PHY implementation, while parallel host access supports embedded processors and programmable logic. A production design must still provide the appropriate Ethernet magnetics or coupling, surge protection, grounding, and enclosure interfaces. Firmware timing and the legacy parallel host arrangement should be validated before using this controller in a new camera or access-control platform.

📡

Data Acquisition and Control Module

The LAN91C111I-NU-E2 fits data-acquisition and industrial control modules that need to move commands, measurements, and diagnostics over a Fast Ethernet link. Its 10 Mbps mode supports constrained or legacy networks, while 100 Mbps mode provides a faster path for higher data volumes. Because the device uses a parallel host interface rather than a PCI interface, the host processor must supply compatible bus control or an interface bridge. Firmware initialization, interrupt handling, and MII timing are critical parts of a reliable implementation.

おすすめ製品の概要

LAN91C111I-NU Closely related Ethernet controller ordering configuration 使用用途: Embedded Industrial Ethernet Controller, Test and Measurement Ethernet Interface, Communications Gateway, Print Server and Network Appliance, Security and Surveillance Endpoint, Data Acquisition and Control Module LAN91C111-NU Microchip Technology 使用用途: Embedded Industrial Ethernet Controller, Test and Measurement Ethernet Interface, Communications Gateway, Print Server and Network Appliance, Security and Surveillance Endpoint, Data Acquisition and Control Module
What is the LAN91C111I-NU-E2?
The LAN91C111I-NU-E2 is an SMSC Corporation single-chip 10/100 Ethernet controller that combines a media access controller and physical layer in a 128-pin TQFP package. According to the manufacturer data sheet, it provides a parallel host interface, supports IEEE 802.3 and IEEE 802.3u operation, and is intended for embedded Fast Ethernet systems rather than PCI-based desktop adapters.
What Ethernet speeds does LAN91C111I-NU-E2 support?
The LAN91C111I-NU-E2 supports both 10 Mbps and 100 Mbps Ethernet operation. The manufacturer data sheet describes a four-bit Media Independent Interface suitable for 10 Mbps and 100 Mbps networks, while the listed specifications identify support for IEEE 802.3 and IEEE 802.3u. This makes the controller appropriate for embedded systems that need both 10BASE-T and 100BASE-TX connectivity.
Does LAN91C111I-NU-E2 include an Ethernet PHY?
Yes, the LAN91C111I-NU-E2 integrates both the Ethernet MAC and PHY in one package. Distributor documentation identifies it as a 10/100 Base-T/TX PHY with a parallel interface, and the manufacturer describes it as a mixed-signal analog/digital device implementing the MAC and PHY portions of CSMA/CD Ethernet. Integrating both functions reduces the external component count for an embedded Ethernet design.
What package does LAN91C111I-NU-E2 use?
The LAN91C111I-NU-E2 is supplied in a 128-pin TQFP package measuring 14 x 14 mm. The exact 128-pin TQFP outline is not represented in the available package-diagram library, so a conventional numbered pinout cannot be published safely. Use the mechanical drawing and pin-description tables in the manufacturer data sheet when assigning PCB lands, with particular attention to the exposed-power and ground connections.
Where can I download the LAN91C111I-NU-E2 datasheet PDF?
The manufacturer LAN91C111 data sheet is available directly from Microchip Technology at the official DeviceDoc PDF address. It contains the device description, MII and management-interface details, electrical characteristics, package information, and application guidance for the LAN91C111 family. Use that document together with the family silicon errata and data sheet clarification when bringing up a new PCB or diagnosing legacy behavior.
Where do I find the LAN91C111I-NU-E2 pinout?
The authoritative LAN91C111I-NU-E2 pinout is in the pin-description table and package drawing in the manufacturer data sheet. The device uses a 128-pin TQFP package, but that exact package is not available in the current diagram library, so publishing a generated 128-pin listing would risk incorrect numbering or missing exposed-pad connections. Assign signals directly from the manufacturer table and preserve the documented exposed-pad connection.
What is the LAN91C111I-NU-E2 supply voltage range?
The listed operating supply range for LAN91C111I-NU-E2 is 2.97 V to 3.63 V. This 3.3 V-class operating range applies to the integrated Ethernet controller and its digital interfaces. Confirm every external PHY, magnetics, isolation, and processor interface voltage in the design against the individual data-sheet limits, because compatible data signals do not necessarily permit direct connection to a 5 V host.
LAN91C111I-NU-E2 vs LAN91C111I-NU: which should I select?
LAN91C111I-NU-E2 and LAN91C111I-NU identify the same LAN91C111I-NU 10/100 Ethernet controller core, but their ordering codes can represent different delivery or packaging treatment. The manufacturer data sheet applies to the family, while purchasing documents should confirm the exact suffix, package, temperature grade, and reel configuration. For a board already designed around the I-NU footprint, select only an ordering code confirmed to use the same 128-pin TQFP land pattern.
When should I choose LAN91C111I-NU-E2 over a discrete MAC and PHY design?
Choose the LAN91C111I-NU-E2 when an embedded system needs a compact 10/100 Ethernet endpoint and its parallel host interface can be supported by the available bus and firmware. The integrated MAC and PHY reduce board area and external PHY complexity. A discrete MAC and PHY remains preferable when the product requires interfaces, features, or software support not provided by the LAN91C111 family.
Is LAN91C111I-NU-E2 suitable for an industrial embedded controller?
The LAN91C111I-NU-E2 includes an industrial-temperature ordering indication and integrates a 10/100 Ethernet MAC and PHY in one device. Its suitability for a specific industrial system still depends on the complete operating-temperature requirement, Ethernet isolation design, electromagnetic-compatibility requirements, firmware support, and long-term availability. Confirm the exact ordering code and all applicable environmental qualifications before production release.
What can replace LAN91C111I-NU-E2?
The closest documented replacement is the LAN91C111I-NU because it identifies the same industrial-temperature, 128-pin TQFP Ethernet controller configuration without the trailing E2 ordering suffix. Before treating it as a drop-in replacement, verify the meaning of E2 in the purchasing record, confirm the reel or tray configuration, and check the LAN91C111 family errata. A different package or host interface is not a drop-in replacement.
Can LAN91C111-NU replace LAN91C111I-NU-E2?
LAN91C111-NU may share the 128-pin TQFP package and the same 10/100 MAC and PHY architecture, but the absence of the I suffix can indicate a different temperature grade. Treat it as a conditional replacement rather than an automatic drop-in: confirm the operating-temperature range, production status, ordering code, exposed-pad treatment, and host-bus compatibility against the manufacturer documentation for both devices.
Is there a cross-brand drop-in equivalent for LAN91C111I-NU-E2?
No cross-brand drop-in equivalent was established by the available component cross-reference information. A genuine replacement must retain the 128-pin TQFP land pattern, parallel host interface, MII implementation, supply range, electrical timing, and firmware register compatibility. Because these requirements constrain interchangeability, changing manufacturers solely from a generic similarity result can introduce driver, timing, or PCB-layout incompatibilities.
What are the key specifications of LAN91C111I-NU-E2 that engineers should know?
The key specifications are 10 Mbps and 100 Mbps Ethernet support, an integrated MAC and PHY, a parallel non-PCI host interface, a four-bit MII, and a 2.97 V to 3.63 V core supply. The device is packaged in a 128-pin, 14 x 14 mm TQFP and supports IEEE 802.3 and IEEE 802.3u. These characteristics place it in embedded Fast Ethernet designs using MII-compatible signal arrangements.
How do I purchase LAN91C111I-NU-E2 and check its lead time?
Use the Request a Quote form on this page to request LAN91C111I-NU-E2 pricing, current availability, minimum order quantity, and production lead time. The exact quantity, suffix treatment, and delivery format should be confirmed during quotation because the E2 ordering code may distinguish a commercial delivery or packaging arrangement. The manufacturer and distributor product pages should be reviewed for lifecycle and traceability requirements before approval.
Is LAN91C111I-NU-E2 currently in stock?
Current stock for the exact LAN91C111I-NU-E2 ordering code should be confirmed through the Request a Quote form on this page. The family remains listed for order, but availability can differ between the base LAN91C111I-NU part and the exact E2 suffix. Provide the required quantity, package format, and date code requirements with the request so the quotation reflects the production configuration you intend to use.

エンジニアリング参考データ: LAN91C111I-NU-E2 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose LAN91C111I-NU-E2 for an embedded 10/100 Ethernet design that specifically requires the non-PCI parallel host architecture, four-bit MII, and established LAN91C111-family software support. Choose LAN91C111I-NU when the same industrial-temperature controller and footprint are required but the trailing E2 delivery treatment is not. Consider LAN91C111-NU only when its non-I temperature grade satisfies the product requirements and the ordering differences have been reviewed. No cross-brand drop-in replacement was established because host-bus timing, register behavior, MII implementation, exposed-pad connections, and firmware support must all align. For new compact products, compare this controller against smaller Ethernet PHY or Ethernet controller options when board area and external bus complexity matter more than retaining a legacy parallel interface.

代替品との比較

パラメータ この製品 LAN91C111I-NU LAN91C111-NU
Package 128-TQFP (14x14) 128-TQFP (14x14) 128-TQFP (14x14)
Brand SMSC Corporation SMSC Corporation SMSC Corporation
Ethernet Speed 10/100 Mbps 10/100 Mbps 10/100 Mbps
Integrated Functions Ethernet MAC and PHY Ethernet MAC and PHY Ethernet MAC and PHY
Host Interface Parallel Parallel Parallel
Bus Architecture Non-PCI Non-PCI Non-PCI
Media Interface 4-bit MII 4-bit MII 4-bit MII
Temperature Ordering Designation I industrial-temperature designation I industrial-temperature designation No I suffix

主な差別化要因

  • Combines the Ethernet MAC and PHY in one controller (vs LAN91C111-NU)
  • Uses the established 128-pin TQFP controller footprint (vs LAN91C111I-NU)
  • Supports parallel MII-based embedded integration (vs LAN91C111-NU)

設計ノート

Allocate the complete 128-pin TQFP land pattern before committing the schematic. The device combines high-speed digital host and MII signals with analog Ethernet functions, so place decoupling and grounding structures according to the manufacturer layout guidance. Keep the parallel host bus traces short, provide solid ground-plane continuity, and avoid routing sensitive network or clock nets beneath areas with high switching activity.

Treat the four-bit MII and its management signals as a coordinated interface rather than independent nets. Match trace lengths where the timing budget requires it, maintain continuous reference planes, and keep the clock path away from Ethernet magnetics and switching-power stages. Validate MII timing with realistic host-bus loading and the final PCB stack-up before releasing fabrication files.

Do not treat a controller with the same TQFP outline as a drop-in replacement without checking exposed-pad connections, supply sequencing, bus timing, interrupt polarity, and firmware register support. In particular, the I suffix changes the temperature designation, while E2 may specify an ordering or delivery treatment. Compare the exact ordering documents and the LAN91C111 family errata before approving an alternative.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The available product information identifies an industrial-temperature ordering code but does not provide compliance declarations. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer product documentation or a signed supplier declaration.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

LAN91C111I-NU-E2 datasheet LAN91C111I-NU-E2 pinout LAN91C111I-NU-E2 datasheet pdf LAN91C111I-NU-E2 equivalent LAN91C111I-NU-E2 replacement LAN91C111I-NU-E2 price LAN91C111I-NU-E2 stock SMSC LAN91C111I-NU-E2 LAN91C111I-NU-E2 10/100 Ethernet LAN91C111I-NU-E2 128 TQFP LAN91C111I-NU-E2 MII interface LAN91C111I-NU-E2 vs LAN91C111I-NU LAN91C111I-NU-E2 embedded Ethernet LAN91C111I-NU-E2 parallel host interface LAN91C111I-NU-E2 schematic

関連部品&用語

SMSC Corporation Microchip Technology LAN91C111I-NU-E2 LAN91C111I-NU LAN91C111-NU Ethernet controller media access controller MAC physical layer PHY Fast Ethernet 10BASE-T 100BASE-TX IEEE 802.3 IEEE 802.3u Media Independent Interface MII parallel host interface non-PCI architecture 128-pin TQFP QFP package surface-mount package 2.97 V to 3.63 V industrial temperature grade embedded networking
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示