LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC
MPN: LAN91C111I-NU-E2 ✓ Hoạt độngLAN91C111I-NU-E2 Tóm tắt
An Ethernet controller is an interface integrated circuit that connects an embedded processing system to a physical Ethernet network. In the hierarchy, the LAN91C111 belongs to Ethernet controllers, interface ICs, integrated circuits, and semiconductors. Integrating the MAC and PHY reduces the number of components required for an embedded Fast Ethernet port, while the parallel interface provides direct access between the controller and external host-bus circuitry.
The LAN91C111 uses a four-bit Media Independent Interface for connections to either 10 Mbps or 100 Mbps Ethernet networks. Three device pins support the two-wire serial MII management protocol. This combination allows the controller to participate in MII-based network designs without requiring the parallel interface to be limited to one Ethernet speed. The controller is intended for embedded systems requiring dedicated Fast Ethernet connectivity rather than a PCI-based desktop adapter.
The device is identified as a 10/100 Base-T/TX PHY controller with a parallel host interface. Its 128-TQFP package provides the mixed-signal and digital connections needed for the MAC, PHY, host interface, and MII functions. Because it combines analog and digital circuitry on one device, PCB implementation requires controlled trace routing, suitable grounding, and careful separation of high-speed digital signals from sensitive network and clock connections.
Typical applications include embedded industrial controllers, test equipment, print servers, communications appliances, and other systems requiring a compact 10/100 Ethernet interface. The integrated MAC and PHY are especially useful when a system cannot accommodate a discrete Ethernet PHY or a separate PCI Ethernet controller. The parallel host interface must still be matched carefully to the target processor, bus logic, and firmware architecture.
When designing around the LAN91C111I-NU-E2, verify the host-bus timing, MII connections, magnetic-interface implementation, and available board area before releasing a PCB layout. The 128-pin package is not physically interchangeable with smaller Ethernet interfaces without a complete board redesign, so footprint and firmware compatibility are as important as nominal Ethernet performance.
This page combines the manufacturer interface information, package identification, ordering details, and engineering guidance for the LAN91C111I-NU-E2. It also documents the distinctions among related LAN91C111 ordering codes and provides practical considerations for evaluating this non-PCI Ethernet controller in an embedded Fast Ethernet design.
Bộ thay thế dễ dàng lắp đặt cho LAN91C111I-NU-E2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LAN91C111I-NU-E2 (cùng hình factor và footprint) — khác nhau ở Host Interface, Package.
LAN91C111I-NU
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LAN91C111-NU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LAN91C111I-NU-E2 Thông số kỹ thuật
| Product Type | 10/100 Ethernet single-chip MAC and PHY controller |
| Ethernet Speed | 10 Mbps and 100 Mbps |
| Host Interface | Parallel interface |
| Bus Architecture | Non-PCI |
| Media Interface | 4-bit MII |
| MII Management Interface | 2-wire serial protocol |
| Core Supply Voltage | 2.97 V to 3.63 V |
| Ethernet Standards | IEEE 802.3 and IEEE 802.3u |
| Hộp | 128-pin TQFP |
| Package Dimensions | 14 x 14 mm |
| Kiểu lắp đặt | Surface mount |
| Temperature Grade | Industrial temperature, indicated by I ordering code |
| Integrated Functions | Ethernet MAC and PHY |
| Physical Layer | 10/100 Base-T/TX PHY |
Hướng dẫn cấu hình chân LAN91C111I-NU-E2 14 x 14 mm
Cấu hình chân cho LAN91C111I-NU-E2 (14 x 14 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho LAN91C111I-NU-E2.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LAN91C111I-NU-E2 phù hợp cho 6 Áp dụngs: Embedded Industrial Ethernet Controller, Test and Measurement Ethernet Interface, Communications Gateway, Print Server and Network Appliance, Security and Surveillance Endpoint, Data Acquisition and Control Module.
Embedded Industrial Ethernet Controller
The LAN91C111I-NU-E2 fits an embedded industrial controller that needs both 10 Mbps and 100 Mbps Ethernet connectivity without adding a separate MAC and PHY. Its integrated 10/100 Base-T/TX physical layer and non-PCI architecture reduce the number of high-speed network components on the board. The parallel host interface can connect to suitable bus logic, while the four-bit MII provides a standardized route to the integrated PHY section. The principal design constraint is the 128-pin TQFP footprint, which requires adequate routing space and careful separation between host, clock, management, and analog network connections.
Được đề xuất
Test and Measurement Ethernet Interface
The LAN91C111I-NU-E2 can provide Fast Ethernet connectivity in test and measurement equipment that must transfer status, results, or configuration data over an embedded network. Supporting 10 Mbps and 100 Mbps allows interoperability with older management networks as well as faster local links. The integrated MAC and PHY simplifies the physical Ethernet portion of the design, but the parallel host interface still requires buffering or glue logic when the host processor does not expose the required bus protocol directly.
Được đề xuất
Communications Gateway
A communications gateway can use the LAN91C111I-NU-E2 to add a dedicated 10/100 Ethernet endpoint to an embedded control platform. The integrated MAC and PHY are useful when the gateway needs a second network function independent of a host-provided PCI or USB Ethernet interface. IEEE 802.3 and IEEE 802.3u operation supports common Fast Ethernet infrastructure. Designers should allocate the 128-pin TQFP footprint correctly and confirm that the processor-side bus timing and firmware driver can support the controller's parallel interface.
Được đề xuất
Print Server and Network Appliance
The LAN91C111I-NU-E2 is suitable for legacy-style print servers and compact network appliances that require one 10/100 Ethernet port implemented with embedded silicon. Its single-chip MAC-and-PHY arrangement reduces board complexity compared with a split implementation, while the non-PCI architecture avoids requiring a desktop peripheral bus. The 128-pin package still demands a larger PCB area than modern highly integrated Ethernet PHYs, so the controller is most attractive where its established software support and legacy host interface are more valuable than minimal footprint.
Được đề xuất
Security and Surveillance Endpoint
The LAN91C111I-NU-E2 can support a compact security or surveillance endpoint that exchanges configuration data and status over 10/100 Ethernet. The integrated physical layer avoids a separate Ethernet PHY implementation, while parallel host access supports embedded processors and programmable logic. A production design must still provide the appropriate Ethernet magnetics or coupling, surge protection, grounding, and enclosure interfaces. Firmware timing and the legacy parallel host arrangement should be validated before using this controller in a new camera or access-control platform.
Được đề xuất
Data Acquisition and Control Module
The LAN91C111I-NU-E2 fits data-acquisition and industrial control modules that need to move commands, measurements, and diagnostics over a Fast Ethernet link. Its 10 Mbps mode supports constrained or legacy networks, while 100 Mbps mode provides a faster path for higher data volumes. Because the device uses a parallel host interface rather than a PCI interface, the host processor must supply compatible bus control or an interface bridge. Firmware initialization, interrupt handling, and MII timing are critical parts of a reliable implementation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LAN91C111I-NU-E2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LAN91C111I-NU | LAN91C111-NU |
|---|---|---|---|
| Package | 128-TQFP (14x14) | 128-TQFP (14x14) | 128-TQFP (14x14) |
| Brand | SMSC Corporation | SMSC Corporation | SMSC Corporation |
| Ethernet Speed | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| Integrated Functions | Ethernet MAC and PHY | Ethernet MAC and PHY | Ethernet MAC and PHY |
| Host Interface | Parallel | Parallel | Parallel |
| Bus Architecture | Non-PCI | Non-PCI | Non-PCI |
| Media Interface | 4-bit MII | 4-bit MII | 4-bit MII |
| Temperature Ordering Designation | I industrial-temperature designation | I industrial-temperature designation | No I suffix |
Bảo phân biệt quan trọng
- Combines the Ethernet MAC and PHY in one controller (vsLAN91C111-NU)
- Uses the established 128-pin TQFP controller footprint (vsLAN91C111I-NU)
- Supports parallel MII-based embedded integration (vsLAN91C111-NU)
Ghi chú thiết kế
Allocate the complete 128-pin TQFP land pattern before committing the schematic. The device combines high-speed digital host and MII signals with analog Ethernet functions, so place decoupling and grounding structures according to the manufacturer layout guidance. Keep the parallel host bus traces short, provide solid ground-plane continuity, and avoid routing sensitive network or clock nets beneath areas with high switching activity.
Treat the four-bit MII and its management signals as a coordinated interface rather than independent nets. Match trace lengths where the timing budget requires it, maintain continuous reference planes, and keep the clock path away from Ethernet magnetics and switching-power stages. Validate MII timing with realistic host-bus loading and the final PCB stack-up before releasing fabrication files.
Do not treat a controller with the same TQFP outline as a drop-in replacement without checking exposed-pad connections, supply sequencing, bus timing, interrupt polarity, and firmware register support. In particular, the I suffix changes the temperature designation, while E2 may specify an ordering or delivery treatment. Compare the exact ordering documents and the LAN91C111 family errata before approving an alternative.
Thông tin tuân thủ
The available product information identifies an industrial-temperature ordering code but does not provide compliance declarations. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer product documentation or a signed supplier declaration.