LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC
N.º da peça: LAN91C111I-NU-E2 ✓ AtivoLAN91C111I-NU-E2 Visão geral
An Ethernet controller is an interface integrated circuit that connects an embedded processing system to a physical Ethernet network. In the hierarchy, the LAN91C111 belongs to Ethernet controllers, interface ICs, integrated circuits, and semiconductors. Integrating the MAC and PHY reduces the number of components required for an embedded Fast Ethernet port, while the parallel interface provides direct access between the controller and external host-bus circuitry.
The LAN91C111 uses a four-bit Media Independent Interface for connections to either 10 Mbps or 100 Mbps Ethernet networks. Three device pins support the two-wire serial MII management protocol. This combination allows the controller to participate in MII-based network designs without requiring the parallel interface to be limited to one Ethernet speed. The controller is intended for embedded systems requiring dedicated Fast Ethernet connectivity rather than a PCI-based desktop adapter.
The device is identified as a 10/100 Base-T/TX PHY controller with a parallel host interface. Its 128-TQFP package provides the mixed-signal and digital connections needed for the MAC, PHY, host interface, and MII functions. Because it combines analog and digital circuitry on one device, PCB implementation requires controlled trace routing, suitable grounding, and careful separation of high-speed digital signals from sensitive network and clock connections.
Typical applications include embedded industrial controllers, test equipment, print servers, communications appliances, and other systems requiring a compact 10/100 Ethernet interface. The integrated MAC and PHY are especially useful when a system cannot accommodate a discrete Ethernet PHY or a separate PCI Ethernet controller. The parallel host interface must still be matched carefully to the target processor, bus logic, and firmware architecture.
When designing around the LAN91C111I-NU-E2, verify the host-bus timing, MII connections, magnetic-interface implementation, and available board area before releasing a PCB layout. The 128-pin package is not physically interchangeable with smaller Ethernet interfaces without a complete board redesign, so footprint and firmware compatibility are as important as nominal Ethernet performance.
This page combines the manufacturer interface information, package identification, ordering details, and engineering guidance for the LAN91C111I-NU-E2. It also documents the distinctions among related LAN91C111 ordering codes and provides practical considerations for evaluating this non-PCI Ethernet controller in an embedded Fast Ethernet design.
Alternativas drop-in para LAN91C111I-NU-E2 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LAN91C111I-NU-E2 (mesmo formato e footprint) — diferindo em Host Interface, Package.
LAN91C111I-NU
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LAN91C111-NU
✅ Drop-InConsulte o preço
Ver ficha técnica →LAN91C111I-NU-E2 Especificações
| Product Type | 10/100 Ethernet single-chip MAC and PHY controller |
| Ethernet Speed | 10 Mbps and 100 Mbps |
| Host Interface | Parallel interface |
| Bus Architecture | Non-PCI |
| Media Interface | 4-bit MII |
| MII Management Interface | 2-wire serial protocol |
| Core Supply Voltage | 2.97 V to 3.63 V |
| Ethernet Standards | IEEE 802.3 and IEEE 802.3u |
| Encapsulamento | 128-pin TQFP |
| Package Dimensions | 14 x 14 mm |
| Tipo de montagem | Surface mount |
| Temperature Grade | Industrial temperature, indicated by I ordering code |
| Integrated Functions | Ethernet MAC and PHY |
| Physical Layer | 10/100 Base-T/TX PHY |
Guia de Configuração de Pinos do LAN91C111I-NU-E2 14 x 14 mm
Configuração de pinos para LAN91C111I-NU-E2 (pacote 14 x 14 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para LAN91C111I-NU-E2.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LAN91C111I-NU-E2 é adequado para 6 aplicaçãos: Embedded Industrial Ethernet Controller, Test and Measurement Ethernet Interface, Communications Gateway, Print Server and Network Appliance, Security and Surveillance Endpoint, Data Acquisition and Control Module.
Embedded Industrial Ethernet Controller
The LAN91C111I-NU-E2 fits an embedded industrial controller that needs both 10 Mbps and 100 Mbps Ethernet connectivity without adding a separate MAC and PHY. Its integrated 10/100 Base-T/TX physical layer and non-PCI architecture reduce the number of high-speed network components on the board. The parallel host interface can connect to suitable bus logic, while the four-bit MII provides a standardized route to the integrated PHY section. The principal design constraint is the 128-pin TQFP footprint, which requires adequate routing space and careful separation between host, clock, management, and analog network connections.
Recomendado
Test and Measurement Ethernet Interface
The LAN91C111I-NU-E2 can provide Fast Ethernet connectivity in test and measurement equipment that must transfer status, results, or configuration data over an embedded network. Supporting 10 Mbps and 100 Mbps allows interoperability with older management networks as well as faster local links. The integrated MAC and PHY simplifies the physical Ethernet portion of the design, but the parallel host interface still requires buffering or glue logic when the host processor does not expose the required bus protocol directly.
Recomendado
Communications Gateway
A communications gateway can use the LAN91C111I-NU-E2 to add a dedicated 10/100 Ethernet endpoint to an embedded control platform. The integrated MAC and PHY are useful when the gateway needs a second network function independent of a host-provided PCI or USB Ethernet interface. IEEE 802.3 and IEEE 802.3u operation supports common Fast Ethernet infrastructure. Designers should allocate the 128-pin TQFP footprint correctly and confirm that the processor-side bus timing and firmware driver can support the controller's parallel interface.
Recomendado
Print Server and Network Appliance
The LAN91C111I-NU-E2 is suitable for legacy-style print servers and compact network appliances that require one 10/100 Ethernet port implemented with embedded silicon. Its single-chip MAC-and-PHY arrangement reduces board complexity compared with a split implementation, while the non-PCI architecture avoids requiring a desktop peripheral bus. The 128-pin package still demands a larger PCB area than modern highly integrated Ethernet PHYs, so the controller is most attractive where its established software support and legacy host interface are more valuable than minimal footprint.
Recomendado
Security and Surveillance Endpoint
The LAN91C111I-NU-E2 can support a compact security or surveillance endpoint that exchanges configuration data and status over 10/100 Ethernet. The integrated physical layer avoids a separate Ethernet PHY implementation, while parallel host access supports embedded processors and programmable logic. A production design must still provide the appropriate Ethernet magnetics or coupling, surge protection, grounding, and enclosure interfaces. Firmware timing and the legacy parallel host arrangement should be validated before using this controller in a new camera or access-control platform.
Recomendado
Data Acquisition and Control Module
The LAN91C111I-NU-E2 fits data-acquisition and industrial control modules that need to move commands, measurements, and diagnostics over a Fast Ethernet link. Its 10 Mbps mode supports constrained or legacy networks, while 100 Mbps mode provides a faster path for higher data volumes. Because the device uses a parallel host interface rather than a PCI interface, the host processor must supply compatible bus control or an interface bridge. Firmware initialization, interrupt handling, and MII timing are critical parts of a reliable implementation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LAN91C111I-NU-E2 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LAN91C111I-NU | LAN91C111-NU |
|---|---|---|---|
| Package | 128-TQFP (14x14) | 128-TQFP (14x14) | 128-TQFP (14x14) |
| Brand | SMSC Corporation | SMSC Corporation | SMSC Corporation |
| Ethernet Speed | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| Integrated Functions | Ethernet MAC and PHY | Ethernet MAC and PHY | Ethernet MAC and PHY |
| Host Interface | Parallel | Parallel | Parallel |
| Bus Architecture | Non-PCI | Non-PCI | Non-PCI |
| Media Interface | 4-bit MII | 4-bit MII | 4-bit MII |
| Temperature Ordering Designation | I industrial-temperature designation | I industrial-temperature designation | No I suffix |
Principais diferenciais
- Combines the Ethernet MAC and PHY in one controller (vs LAN91C111-NU)
- Uses the established 128-pin TQFP controller footprint (vs LAN91C111I-NU)
- Supports parallel MII-based embedded integration (vs LAN91C111-NU)
Notas de projeto
Allocate the complete 128-pin TQFP land pattern before committing the schematic. The device combines high-speed digital host and MII signals with analog Ethernet functions, so place decoupling and grounding structures according to the manufacturer layout guidance. Keep the parallel host bus traces short, provide solid ground-plane continuity, and avoid routing sensitive network or clock nets beneath areas with high switching activity.
Treat the four-bit MII and its management signals as a coordinated interface rather than independent nets. Match trace lengths where the timing budget requires it, maintain continuous reference planes, and keep the clock path away from Ethernet magnetics and switching-power stages. Validate MII timing with realistic host-bus loading and the final PCB stack-up before releasing fabrication files.
Do not treat a controller with the same TQFP outline as a drop-in replacement without checking exposed-pad connections, supply sequencing, bus timing, interrupt polarity, and firmware register support. In particular, the I suffix changes the temperature designation, while E2 may specify an ordering or delivery treatment. Compare the exact ordering documents and the LAN91C111 family errata before approving an alternative.
Informações de conformidade
The available product information identifies an industrial-temperature ordering code but does not provide compliance declarations. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer product documentation or a signed supplier declaration.