LM2903DGKR - Dual Open-Collector Comparator | Texas Instruments
部品番号: LM2903DGKR ✓ 生産中LM2903DGKR 概要
A comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. In the broader semiconductor hierarchy, LM2903 belongs to the comparator and linear IC family, where it bridges analog signal sensing and digital control. Each LM2903 channel combines a differential input pair with an open-collector output, allowing the output stage to pull a logic rail low when the comparison state requires it.
The LM2903DGKR provides two channels in one package, reducing board area compared with separate single comparators. Its open-collector outputs support wired-AND behavior when multiple channels pull a shared bus low, while external pull-up resistors establish the high logic voltage. Rail-to-rail input capability extends the usable common-mode range toward the supply rails, which is useful in battery-powered and low-voltage systems. Its stated 1.3-microsecond response time supports general-purpose detection rather than high-speed timing applications.
The operating range of 2 V to 36 V makes the device suitable for low-voltage control circuits and higher-voltage industrial systems. Common-mode operation from -1 V to +18 V permits signal sensing beyond the lower supply rail. Each output remains electrically open at the collector, so designers can select pull-up voltage, interface to open-drain logic, or connect several outputs to a shared bus. The 8-pin VSSOP package supports compact surface-mount layouts but requires careful handling because its lead pitch is narrower than that of standard SOIC packages.
Typical uses include DC overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control inputs, battery monitoring, and open-drain logic interfacing. In each case, resistor values should be chosen from the applied input range, output pull-up requirement, output leakage, and permissible sink current rather than from a single fixed rule.
When laying out an LM2903DGKR circuit, place input and output components close to their associated pins and keep switching-current paths away from the differential inputs. Add a local supply bypass capacitor to limit transient coupling into the comparison threshold. The open-collector output also requires a pull-up resistor in every configuration where a valid high output is required.
This product record combines the manufacturer ordering information, package and functional characteristics, verified replacement candidates, and practical layout guidance. It is intended to help engineers evaluate LM2903DGKR for open-collector comparator designs while accounting for voltage range, response time, channel count, and board-space constraints.
ドロップイン代替品: LM2903DGKR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2903DGKR (同一形状・フットプリント) — 相違点: Comparator Type, Package, Output Type.
LM2903BIDGKR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903DGKR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903DGKR 最大定格&電気的特性
| Comparator Type | Dual differential, general-purpose comparator |
| Number of Channels | 2 channels |
| 出力タイプ | Open-collector |
| Input Common-Mode Capability | Rail-to-rail |
| Supply Voltage Range | 2 V to 36 V |
| Common-Mode Input Voltage Range | -1 V to +18 V |
| Response Time | 1.3 us |
| パッケージ | 8-pin VSSOP |
| Package Family | VSSOP-8 surface-mount family |
| 実装タイプ | Surface mount |
LM2903DGKR ピン構成
| ピン 1 | 1OUT — Open-collector output for comparator channel 1 |
| ピン 2 | 1IN- — Inverting input for comparator channel 1 |
| ピン 3 | 1IN+ — Non-inverting input for comparator channel 1 |
| ピン 4 | GND — Ground connection |
| ピン 5 | 2IN+ — Non-inverting input for comparator channel 2 |
| ピン 6 | 2IN- — Inverting input for comparator channel 2 |
| ピン 7 | 2OUT — Open-collector output for comparator channel 2 |
| ピン 8 | VCC — Positive supply connection |
主な用途
LM2903DGKR の用途: 6 件s: Industrial Voltage Threshold Detection, Battery Pack Overvoltage Detection, Sensor Signal Conditioning, Open-Drain Logic Interfacing, Motor Control and Drive Monitoring, Consumer and Communication Threshold Logic.
Industrial Voltage Threshold Detection
The LM2903DGKR suits industrial control inputs that determine whether a monitored voltage is above or below a defined threshold. Its 2 V to 36 V operating range supports a wide range of supplied systems, while the -1 V to +18 V common-mode input range allows sensing near the lower rail. Place the threshold-setting divider at the appropriate comparison input and use the 1.3 us response time for ordinary alarm and interlock functions. The open-collector output can drive a pulled-up status line or participate in a wired fault bus. Industrial implementation should also account for transients, grounding, and the separation of high-energy wiring from sensitive comparator traces.
おすすめ
Battery Pack Overvoltage Detection
LM2903DGKR can supervise a battery-derived voltage and assert a fault indication when the monitored node crosses a selected limit. The comparator's 2 V minimum operating voltage and -1 V minimum common-mode input voltage provide useful flexibility when sensing a rail near the lower supply boundary. A resistor-divider network establishes the reference, and the open-collector output drives a pulled-up fault signal with its polarity determined by which differential input receives the reference. For battery systems, select divider resistors for the actual cell chemistry and fault threshold, then confirm input current, transient energy, and the output pull-up voltage in the complete design.
おすすめ
Sensor Signal Conditioning
The LM2903DGKR is useful when a sensor produces a slowly changing analog signal that must be converted into a thresholded digital decision. Its differential inputs allow a sensed voltage to be compared with a locally generated reference, and its 1.3 us response time is suitable for many temperature, position, and level signals that do not require nanosecond decision speed. Rail-to-rail input operation supports low-voltage sensing systems. Place the source and reference paths close to the input pins, bypass the supply locally, and route the open-collector output away from sensitive sensor wiring. Add hysteresis when the threshold signal is noisy or when chatter at the switching point could cause repeated downstream actions.
おすすめ
Open-Drain Logic Interfacing
LM2903DGKR can act as the analog decision stage in an open-drain or open-collector bus because each output can pull a shared line low when its comparison condition is met. This architecture supports wired-AND behavior, external pull-up selection, and isolation between the comparator output and a higher-voltage or lower-voltage logic domain. Use each output with an appropriate pull-up resistor, verify the maximum sink current and logic-level compatibility, and avoid exceeding the 36 V supply rating. The 8-pin VSSOP footprint saves board area, but its narrow lead pitch and exposed thermal considerations should be incorporated into assembly planning and PCB design rules.
おすすめ
Motor Control and Drive Monitoring
The LM2903DGKR can monitor a control-system voltage or protected feedback node before allowing a motor-drive stage to operate. Its dual-channel architecture permits two independent comparisons, such as an enable condition and a current-sense threshold, within one package. The 1.3 us response time supports general-purpose protection rather than protection requiring sub-microsecond timing. Because motor environments contain switching noise and large transients, keep the comparator away from motor-current paths, provide a local supply bypass, and use filtered references. The open-collector output can pull up a fault or disable line, but the external pull-up and downstream logic must remain compatible with the operating voltage and fault-management architecture.
おすすめ
Consumer and Communication Threshold Logic
LM2903DGKR can implement simple decision logic in consumer accessories, communications equipment, and embedded control systems where two analog quantities must be compared. The compact 8-pin VSSOP package fits space-constrained boards, and the dual configuration supports channel pairing without requiring two separate packages. A typical circuit applies a resistor-divider reference to one input, feeds the sensed or derived voltage to the other, and uses the open-collector result to control a pulled-up enable or status signal. Design the threshold around the 2 V to 36 V operating range and the -1 V to +18 V common-mode range, and include hysteresis where the compared signal changes slowly.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2903DGKR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2903BIDGKR | LM2903DGKR |
|---|---|---|---|
| Package | 8-pin VSSOP | 8-pin VSSOP | 8-MSOP/VSSOP |
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Comparator Channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector |
主な差別化要因
- Broader supply-voltage operating range than a basic 5 V comparator (vs LM2903BIDGKR)
- Open-collector outputs support flexible bus and pull-up configurations (vs ROHM LM2903DGKR)
- Dual-channel integration reduces component count (vs ROHM LM2903DGKR)
設計ノート
Place the input-network components and local supply bypass capacitor close to the LM2903DGKR pins to minimize parasitic pickup and supply bounce at the comparison threshold. Route the two differential inputs as a compact pair, keep them away from switching-node copper and relay or motor wiring, and provide a continuous ground reference. Because the part uses an 8-pin VSSOP package, verify the narrow lead pitch and exposed-pad requirements against the manufacturer land pattern before releasing artwork.
Every open-collector output requires a pull-up resistor whenever a valid high state is required. Select the pull-up from the intended logic voltage, the output's allowable sink current, and the required rise time rather than from a generic value. Keep the pull-up return current within the comparator's output limits, and account for the pull-up current when evaluating total system power. Do not apply voltages above the documented 36 V maximum for this ordering code.
Avoid comparing signals that can exceed the -1 V to +18 V common-mode input range, even when the supply itself remains within limits. Input protection structures can inject current or experience damage outside the specified range. Add hysteresis when noise or slow signal transitions could cause output chatter, and use the B-family option only after reviewing its updated electrical table if a higher maximum rating or faster response time is required.
コンプライアンス情報
Compliance status was not stated in the available manufacturer and distributor information. Automotive qualification is not asserted because no AEC-Q100 status was identified for this ordering code.