LM2903WYDT - Dual 2-36V Low-Power Comparator | STMicroelectronics
部品番号: LM2903WYDT ✓ 生産中LM2903WYDT 概要
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy, within analog signal conditioning and interface ICs. Its open-collector outputs can pull external buses or logic inputs down, while external pull-up resistors establish the high output state. Each comparator operates independently, allowing one package to implement two sensing functions.
Key features include a wide 2 V to 36 V supply range, low typical quiescent current of 0.4 mA, and a typical input offset voltage of 25 nA. The open-collector output supports wired logic, relay or solenoid interfaces, and compatibility with multiple logic families when suitable pull-up components are used. The SOIC-8 surface-mount package keeps the dual-channel implementation compact while supporting automated board assembly.
The two channels provide common-mode input range and input-offset behavior suited to precision threshold detection. Because the outputs are open collector, the transition speed depends partly on output load capacitance, the external pull-up resistance, and the pull-up voltage. Designers should account for these external factors when setting propagation-delay requirements or operating the outputs at high bus speeds.
Typical uses include battery-powered monitoring, industrial sensor interfaces, window or level comparison, power-good detection, overvoltage and undervoltage protection, and general-purpose control logic. The broad supply range is especially useful in equipment operating from regulated low-voltage rails or from higher industrial supply rails after suitable protection and decoupling.
For reliable operation, place the supply bypass capacitor close to the device, use a pull-up resistor on each open-collector output, and verify that input and output absolute-maximum limits are not exceeded during power transitions. Check input common-mode range and differential input limits against the actual signal excursion, and confirm that the external pull-up voltage remains within the output-pin rating.
This product page combines the manufacturer device description, distributor package information, technical characteristics, qualified drop-in alternatives, and practical interface guidance. It supports faster component selection while preserving the pin, voltage, and output-configuration checks required for production designs.
ドロップイン代替品: LM2903WYDT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2903WYDT (同一形状・フットプリント) — 相違点: Comparator Type, Output Type, Package, Input Bias Current, Input Offset Voltage.
LM2903HDT
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LM2903YDT
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903BIDR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903BIDR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903D
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2903WYDT 最大定格&電気的特性
| Comparator Count | 2 independent comparators |
| Supply Voltage Range | 2 V to 36 V |
| 静止電流 | 0.4 mA typical |
| Input Offset Voltage | 25 nA typical |
| 出力タイプ | Open-collector |
| Comparator Type | General-purpose voltage comparator |
| Supply Configuration | Single supply; split supply operation supported |
| パッケージ | 8-pin SOIC |
| 実装タイプ | Surface mount |
| Packaging | Tape and reel |
| 動作温度範囲 | -40 °C to +125 °C |
LM2903WYDT 8-pin soic ピン配置ガイド
LM2903WYDT (8-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LM2903WYDT.
詳細は データシート をご参照ください。
主な用途
LM2903WYDT の用途: 6 件s: Industrial Sensor Threshold Detection, Battery-Powered Monitoring, Power-Good and Overvoltage Detection, Open-Collector Interface and Relay Control, Temperature and Level Limit Monitoring, Automotive and Heavy Equipment Logic.
Industrial Sensor Threshold Detection
The LM2903WYDT fits industrial sensor interfaces that convert an analog measurement into a logic decision. Its two independent comparators can evaluate upper and lower limits in one 8-SOIC package, while the typical 25 nA input offset supports decisions close to the reference threshold. Each open-collector output can pull down a controller input or alarm line through a suitable pull-up resistor. The 2 V to 36 V supply range supports low-voltage sensor rails and higher industrial supply systems. Confirm the signal's common-mode range, protect external connector inputs from transients, and select pull-up values that balance noise immunity against output rise time.
おすすめ
Battery-Powered Monitoring
The LM2903WYDT is appropriate for battery-powered equipment that monitors supply thresholds, charger state, or a divided battery voltage. Its typical 0.4 mA power consumption limits the continuous overhead of two comparison channels, and operation begins at a 2 V supply. The open-collector outputs can directly pull an enable, status, or interrupt line low. Because the output high voltage is established by the external pull-up, the designer can match that voltage to the monitored system while remaining within the device's output limits. Use a low-leakage divider for the battery signal and verify idle current across the complete power-management sequence.
おすすめ
Power-Good and Overvoltage Detection
The LM2903WYDT can implement independent power-good and overvoltage functions by comparing divided supply rails with internal or external references. Its 2 V to 36 V operating range supports a broad range of regulated and industrial input rails, while the dual-channel configuration avoids using two separate comparator packages. Open-collector outputs allow wired fault signaling without an internal push-pull driver. Consider the pull-up supply carefully: it determines the fault-signal voltage and the amount of current the comparator must sink during a fault. Add input filtering and transient protection where the monitored rail can overshoot during hot-plug or load-dump events.
おすすめ
Open-Collector Interface and Relay Control
The LM2903WYDT suits logic-interface and relay-control circuits because its open-collector outputs can sink external loads while the pull-up sets the inactive voltage. This arrangement supports wired-open-collector buses, alarm inputs, and relay-driver interfaces when the load voltage and current remain within the output ratings. The two channels can control separate status signals or implement complementary conditions. Place the pull-up resistor near the receiving logic input, keep the output trace away from sensitive analog paths, and account for inductive kickback when the output drives a relay coil. A flyback diode and adequate trace width may be required depending on the load.
おすすめ
Temperature and Level Limit Monitoring
The LM2903WYDT can compare a temperature-sensor or level-sensor output with a threshold in a compact dual-channel design. The typical 25 nA offset minimizes the error contributed by the comparator itself, while the -40 °C to +125 °C operating range covers many industrial environments. The open-collector output can report an alarm or inhibit a load through an external pull-up. Use a sensor with a suitable transfer function and low enough output impedance for the input network. Validate accuracy across temperature, supply tolerance, and sensor tolerance because the comparator specification alone does not define total system accuracy.
おすすめ
Automotive and Heavy Equipment Logic
The LM2903WYDT is a candidate for low-voltage equipment logic where a compact dual comparator, wide supply range, and extended -40 °C to +125 °C operation are important. It can monitor brake, battery, actuator, or equipment-state signals when those signals remain inside the comparator's input limits. The open-collector architecture is useful for diagnostic lines that use pull-up resistors. The exact ordering variant should be checked for automotive qualification requirements rather than assumed from the commercial temperature range alone. Production designs should also include reverse-battery, load-dump, ESD, and transient protection appropriate to the vehicle or machine environment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2903WYDT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2903HDT | LM2903YDT | LM2903B | LM2903 | LM2903D |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC ordering option | 8-pin SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | onsemi |
| Comparator Count | 2 independent comparators | 2 independent comparators | 2 independent comparators | Dual comparator | Dual differential comparator | Dual comparator |
| Output Configuration | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
主な差別化要因
- Combines two independent channels with a wide supply range (vs LM2903D)
- Low typical power consumption for continuous threshold monitoring (vs LM2903HDT)
- Open-collector output supports flexible wired-logic interfaces (vs LM2903B)
- Extended 125 °C upper operating temperature (vs LM2903HDT)
設計ノート
Use the STMicroelectronics LM2903W datasheet limits to define the operating and absolute-maximum regions. Keep continuous supply voltage within 2 V to 36 V, and include separate checks for input and output pins because an open-collector pull-up can expose an output to a voltage different from the device supply. Decouple the supply pin near the package with a ceramic capacitor selected for the required voltage rating and effective capacitance.
The open-collector output cannot source current, so omitting the pull-up resistor leaves the output node undefined when the comparator is inactive. Select the resistor using the receiving logic's high-level requirement, output sink-current limit, supply voltage, and acceptable rise time. The high-state voltage equals the pull-up supply, making it essential to verify that this voltage remains within the output-pin rating.
Treat each comparator input as a high-impedance node and minimize leakage current through nearby PCB surfaces, humidity, and contaminated flux. In high-impedance threshold circuits, resistor-network current should be substantially greater than input bias current, and input traces should be guarded against nearby switching nodes. Add hysteresis with positive feedback when the compared signal crosses the threshold slowly or contains noise.
Place the supply bypass capacitor and each pull-up resistor close to their associated device pins. Route output traces away from sensitive analog inputs to reduce crosstalk from the rising edge. For long or high-impedance input nodes, use a shield or driven guard if leakage or capacitive pickup is significant. The SOIC-8 land pattern and soldering profile must follow the manufacturer package drawing.
コンプライアンス情報
No explicit compliance declarations are present in the manufacturer or distributor information used for this product record.