STMicroelectronics

LM2903WYDT - Dual 2-36V Low-Power Comparator | STMicroelectronics

MPN: LM2903WYDT ✓ فعال
2 V to 36 V Vdss 0.4 mA typical Id 8-pin SOIC Package
حداقل سفارش: 1 |

LM2903WYDT نمای کلی

The STMicroelectronics LM2903WYDT is a dual low-power voltage comparator with two independent channels, a 2 V to 36 V single-supply operating range, approximately 400 uA power consumption, and 25 nA typical input offset voltage in an 8-pin SOIC package. It is designed for industrial threshold detection, sensing, and open-collector interface applications that require wide supply-voltage tolerance.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy, within analog signal conditioning and interface ICs. Its open-collector outputs can pull external buses or logic inputs down, while external pull-up resistors establish the high output state. Each comparator operates independently, allowing one package to implement two sensing functions.

Key features include a wide 2 V to 36 V supply range, low typical quiescent current of 0.4 mA, and a typical input offset voltage of 25 nA. The open-collector output supports wired logic, relay or solenoid interfaces, and compatibility with multiple logic families when suitable pull-up components are used. The SOIC-8 surface-mount package keeps the dual-channel implementation compact while supporting automated board assembly.

The two channels provide common-mode input range and input-offset behavior suited to precision threshold detection. Because the outputs are open collector, the transition speed depends partly on output load capacitance, the external pull-up resistance, and the pull-up voltage. Designers should account for these external factors when setting propagation-delay requirements or operating the outputs at high bus speeds.

Typical uses include battery-powered monitoring, industrial sensor interfaces, window or level comparison, power-good detection, overvoltage and undervoltage protection, and general-purpose control logic. The broad supply range is especially useful in equipment operating from regulated low-voltage rails or from higher industrial supply rails after suitable protection and decoupling.

For reliable operation, place the supply bypass capacitor close to the device, use a pull-up resistor on each open-collector output, and verify that input and output absolute-maximum limits are not exceeded during power transitions. Check input common-mode range and differential input limits against the actual signal excursion, and confirm that the external pull-up voltage remains within the output-pin rating.

This product page combines the manufacturer device description, distributor package information, technical characteristics, qualified drop-in alternatives, and practical interface guidance. It supports faster component selection while preserving the pin, voltage, and output-configuration checks required for production designs.

جایگزین‌های drop-in برای LM2903WYDT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای LM2903WYDT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Comparator Type, Output Type, Package, Input Bias Current, Input Offset Voltage.

Texas Instruments
Comparator Type: Dual differential comparator
Package: 8-pin SOIC (D)
Input Bias Current: 3.5 nA
مقایسه با LM2903WYDT →
Texas Instruments
Comparator Type: Dual differential comparator
مقایسه با LM2903WYDT →
STMicroelectronics
Comparator Type: Dual differential voltage comparator
Output Type: Open collector
Input Bias Current: 25 nA typical
مقایسه با LM2903WYDT →

LM2903HDT

✅ جایگزین مستقیم
📦 8-pin SOIC
Same dual comparator architecture and 8-SOIC footprint; the listed 2 V to 36 V supply, 0.4 mA power, and 25 nA offset ratings show 0% difference, while the device grade must be checked

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2903YDT

✅ جایگزین مستقیم
STMicroelectronics
📦 8-pin SOIC
Dual differential voltage comparator · 2 channels · +2 V to +36 V · ±1 V to ±18 V · 0.4 mA typical · 1 mW at +5 V · 25 nA typical · ±5 nA typical

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903BIDR

✅ جایگزین مستقیم
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903BIDR

✅ جایگزین مستقیم
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903D

✅ جایگزین مستقیم
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903WYDT حداکثر مقادیر مجاز و مشخصات الکتریکی

Comparator Count 2 independent comparators
Supply Voltage Range 2 V to 36 V
جریان سکون 0.4 mA typical
Input Offset Voltage 25 nA typical
نوع خروجی Open-collector
Comparator Type General-purpose voltage comparator
Supply Configuration Single supply; split supply operation supported
بسته‌بندی 8-pin SOIC
نوع نصب Surface mount
Packaging Tape and reel
محدوده دمای کاری -40 °C to +125 °C

راهنمای پیکربندی پین LM2903WYDT 8-pin soic

پیکربندی پین برای LM2903WYDT (پکیج 8-pin soic). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.

نمودار پین‌آوت پکیج 8-pin soic برای LM2903WYDT

داده پین‌آوت تفصیلی موجود نیست برای LM2903WYDT.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

LM2903WYDT مناسب است برای 6 کاربردs: Industrial Sensor Threshold Detection, Battery-Powered Monitoring, Power-Good and Overvoltage Detection, Open-Collector Interface and Relay Control, Temperature and Level Limit Monitoring, Automotive and Heavy Equipment Logic.

🏭

Industrial Sensor Threshold Detection

The LM2903WYDT fits industrial sensor interfaces that convert an analog measurement into a logic decision. Its two independent comparators can evaluate upper and lower limits in one 8-SOIC package, while the typical 25 nA input offset supports decisions close to the reference threshold. Each open-collector output can pull down a controller input or alarm line through a suitable pull-up resistor. The 2 V to 36 V supply range supports low-voltage sensor rails and higher industrial supply systems. Confirm the signal's common-mode range, protect external connector inputs from transients, and select pull-up values that balance noise immunity against output rise time.

⚡

Battery-Powered Monitoring

The LM2903WYDT is appropriate for battery-powered equipment that monitors supply thresholds, charger state, or a divided battery voltage. Its typical 0.4 mA power consumption limits the continuous overhead of two comparison channels, and operation begins at a 2 V supply. The open-collector outputs can directly pull an enable, status, or interrupt line low. Because the output high voltage is established by the external pull-up, the designer can match that voltage to the monitored system while remaining within the device's output limits. Use a low-leakage divider for the battery signal and verify idle current across the complete power-management sequence.

🔧

Power-Good and Overvoltage Detection

The LM2903WYDT can implement independent power-good and overvoltage functions by comparing divided supply rails with internal or external references. Its 2 V to 36 V operating range supports a broad range of regulated and industrial input rails, while the dual-channel configuration avoids using two separate comparator packages. Open-collector outputs allow wired fault signaling without an internal push-pull driver. Consider the pull-up supply carefully: it determines the fault-signal voltage and the amount of current the comparator must sink during a fault. Add input filtering and transient protection where the monitored rail can overshoot during hot-plug or load-dump events.

🔌

Open-Collector Interface and Relay Control

The LM2903WYDT suits logic-interface and relay-control circuits because its open-collector outputs can sink external loads while the pull-up sets the inactive voltage. This arrangement supports wired-open-collector buses, alarm inputs, and relay-driver interfaces when the load voltage and current remain within the output ratings. The two channels can control separate status signals or implement complementary conditions. Place the pull-up resistor near the receiving logic input, keep the output trace away from sensitive analog paths, and account for inductive kickback when the output drives a relay coil. A flyback diode and adequate trace width may be required depending on the load.

🌡️

Temperature and Level Limit Monitoring

The LM2903WYDT can compare a temperature-sensor or level-sensor output with a threshold in a compact dual-channel design. The typical 25 nA offset minimizes the error contributed by the comparator itself, while the -40 °C to +125 °C operating range covers many industrial environments. The open-collector output can report an alarm or inhibit a load through an external pull-up. Use a sensor with a suitable transfer function and low enough output impedance for the input network. Validate accuracy across temperature, supply tolerance, and sensor tolerance because the comparator specification alone does not define total system accuracy.

🚗

Automotive and Heavy Equipment Logic

The LM2903WYDT is a candidate for low-voltage equipment logic where a compact dual comparator, wide supply range, and extended -40 °C to +125 °C operation are important. It can monitor brake, battery, actuator, or equipment-state signals when those signals remain inside the comparator's input limits. The open-collector architecture is useful for diagnostic lines that use pull-up resistors. The exact ordering variant should be checked for automotive qualification requirements rather than assumed from the commercial temperature range alone. Production designs should also include reverse-battery, load-dump, ESD, and transient protection appropriate to the vehicle or machine environment.

What is the LM2903WYDT?
The LM2903WYDT is an STMicroelectronics dual, general-purpose voltage comparator packaged in an 8-pin SOIC. According to the STMicroelectronics LM2903W datasheet, the device contains two independent low-power comparators and can operate from a single supply over a 2 V to 36 V range. Its open-collector outputs make it suitable for threshold detection, sensing, and logic-interface circuits.
What is the supply voltage range of the LM2903WYDT?
The LM2903WYDT operates from 2 V to 36 V when powered from a single supply. The STMicroelectronics LM2903W datasheet also states that operation from split power supplies is possible. Keep the total applied voltage and each input or output terminal within the device's absolute-maximum ratings, and account for transients when the circuit connects to an external supply.
How much current does the LM2903WYDT consume?
The LM2903WYDT has a typical low-power consumption of approximately 0.4 mA. This figure appears in the distributor technical description for the device and is consistent with its role as a low-power dual comparator. Actual system consumption also depends on the pull-up resistor values, output duty cycle, supply voltage, and the operating state of both comparator channels.
What is the input offset voltage of the LM2903WYDT?
The LM2903WYDT has a typical input offset voltage of 25 nA. This low value supports accurate decisions near the switching threshold when both inputs remain inside their permitted common-mode operating region. For a high-precision design, account separately for resistor tolerance, temperature drift, input bias currents, and the common-mode voltage rather than relying only on the typical offset figure.
Where can I download the LM2903WYDT datasheet PDF?
The official LM2903W datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/lm2903w.pdf. It describes the two low-power comparator channels, supply limits, electrical characteristics, pin configuration, and application information. Use the manufacturer document for production design decisions because package drawings, limits, and test conditions should be checked against the exact ordering code.
Where is the LM2903WYDT pinout?
The LM2903WYDT pin configuration is shown in the manufacturer LM2903W datasheet. The device uses an 8-pin SOIC package with two independent comparator channels and two open-collector outputs. Before assigning PCB tracks, use the pin-description and package-outline sections of the manufacturer datasheet to confirm signal names, exposed connections, pin numbering, and land-pattern dimensions.
Can the LM2903WYDT operate from split power supplies?
Yes, the LM2903WYDT can operate from split power supplies as well as from a single supply. The manufacturer LM2903W datasheet explicitly identifies split-supply operation. Each input voltage and output pull-up voltage must still remain within the applicable absolute-maximum and common-mode limits. Confirm the input common-mode range at the actual supply and signal levels before finalizing the circuit.
Why does the LM2903WYDT output need a pull-up resistor?
Each LM2903WYDT output is open collector, so it actively pulls the output node toward ground but cannot drive a high voltage by itself. An external pull-up resistor establishes the high state. Select the resistor to balance sink-current capability, rise time, power consumption, and the voltage tolerated by the output pin; increasing resistance reduces loading but slows the rising edge through output capacitance.
What can replace the LM2903WYDT?
The LM2903HDT and LM2903YDT from STMicroelectronics are drop-in candidates in the same comparator family and SOIC-8 format, while the onsemi LM2903D is a cross-brand 8-SOIC alternative. The STMicroelectronics LM2903B family is also identified as a drop-in replacement for LM2903 devices. Confirm input limits, output ratings, temperature grade, and open-collector behavior against the original circuit before production use.
LM2903WYDT vs LM2903HDT - which is better?
The LM2903WYDT is the appropriate choice when the required operating range includes -40 °C to +125 °C and an 8-pin SOIC implementation is required. The LM2903HDT is a closely related STMicroelectronics comparator variant, but its exact temperature grade and ordering details must be checked in its datasheet. Both belong to the dual low-power open-collector LM2903 family and use the same SOIC-8 format.
When should I choose the LM2903WYDT instead of an LM393?
Choose the LM2903WYDT when the design specifically requires its dual low-power comparator configuration, 2 V to 36 V supply capability, and -40 °C to +125 °C operating range. An LM393 may offer a different input-offset, supply, temperature, or automotive qualification profile. Compare the complete electrical limits rather than relying only on the shared dual-comparator and open-collector functions.
Is the LM2903WYDT suitable for industrial sensing applications?
The LM2903WYDT is suitable for many industrial sensing applications because it combines two independent channels, a 2 V to 36 V supply range, 0.4 mA typical power consumption, and operation from -40 °C to +125 °C. It is particularly useful for threshold comparison and open-collector interfacing. Input common-mode limits, noise margin, pull-up voltage, and transient protection must be validated for the individual installation.
How do I calculate the LM2903WYDT output rise time?
The LM2903WYDT output rise time depends on the external pull-up resistance, pull-up voltage, total output capacitance, and the comparator's output characteristics. Estimate the RC rise interval with a pull-up resistance multiplied by the connected capacitance, then verify the result against the required bus timing. A smaller pull-up produces a faster edge but increases sink-current demand and high-state power dissipation.
Where can I buy the LM2903WYDT and check its lead time?
Use the Request a Quote form on this page to request the current LM2903WYDT price, stock position, minimum order quantity, and lead time from XAIPART. The device is identified in distributor listings as an 8-pin SOIC, tape-and-reel packaged comparator. Commercial availability can change, so obtain a written quotation for the exact MPN before committing the component to a production schedule.
What are the key specifications of LM2903WYDT that engineers should know?
The LM2903WYDT integrates two independent low-power comparators, operates from 2 V to 36 V, consumes approximately 0.4 mA, and has a 25 nA typical input offset voltage. It uses open-collector outputs and an 8-pin SOIC package. According to the STMicroelectronics LM2903W datasheet, the specified operating temperature range is -40 °C to +125 °C and split-supply operation is supported.

داده‌های مرجع مهندسی برای LM2903WYDT — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the LM2903WYDT for compact dual-channel threshold detection where a 2 V to 36 V supply, 0.4 mA typical consumption, 25 nA typical input offset, and open-collector outputs meet the design requirements. Select LM2903HDT or LM2903YDT when their specific ordering grade better matches the required temperature range or qualification conditions. Consider Texas Instruments LM2903 or LM2903B when an alternative manufacturer's documentation, sourcing, or revised B-version characteristics are preferred, but verify common-mode range, differential input limits, output current, and timing. The onsemi LM2903D is a cross-brand 8-SOIC option with documented CMOS, DTL, ECL, MOS, and TTL compatibility. Whichever option is selected, confirm the exact package, pinout, temperature grade, input limits, output ratings, and open-collector pull-up requirements before releasing a production design.

مقایسه با جایگزین‌ها

پارامتر این محصول LM2903HDT LM2903YDT LM2903B LM2903 LM2903D
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC ordering option 8-pin SOIC
Brand STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments onsemi
Comparator Count 2 independent comparators 2 independent comparators 2 independent comparators Dual comparator Dual differential comparator Dual comparator
Output Configuration Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector

تفاوت‌های کلیدی

  • Combines two independent channels with a wide supply range (در مقابلLM2903D)
  • Low typical power consumption for continuous threshold monitoring (در مقابلLM2903HDT)
  • Open-collector output supports flexible wired-logic interfaces (در مقابلLM2903B)
  • Extended 125 °C upper operating temperature (در مقابلLM2903HDT)

یادداشت‌های طراحی

Use the STMicroelectronics LM2903W datasheet limits to define the operating and absolute-maximum regions. Keep continuous supply voltage within 2 V to 36 V, and include separate checks for input and output pins because an open-collector pull-up can expose an output to a voltage different from the device supply. Decouple the supply pin near the package with a ceramic capacitor selected for the required voltage rating and effective capacitance.

The open-collector output cannot source current, so omitting the pull-up resistor leaves the output node undefined when the comparator is inactive. Select the resistor using the receiving logic's high-level requirement, output sink-current limit, supply voltage, and acceptable rise time. The high-state voltage equals the pull-up supply, making it essential to verify that this voltage remains within the output-pin rating.

Treat each comparator input as a high-impedance node and minimize leakage current through nearby PCB surfaces, humidity, and contaminated flux. In high-impedance threshold circuits, resistor-network current should be substantially greater than input bias current, and input traces should be guarded against nearby switching nodes. Add hysteresis with positive feedback when the compared signal crosses the threshold slowly or contains noise.

Place the supply bypass capacitor and each pull-up resistor close to their associated device pins. Route output traces away from sensitive analog inputs to reduce crosstalk from the rising edge. For long or high-impedance input nodes, use a shield or driven guard if leakage or capacitive pickup is significant. The SOIC-8 land pattern and soldering profile must follow the manufacturer package drawing.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

No explicit compliance declarations are present in the manufacturer or distributor information used for this product record.

تاریخ تأیید داده‌ها: 2026-11-17 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

LM2903WYDT datasheet LM2903WYDT pinout LM2903WYDT datasheet pdf LM2903WYDT equivalent LM2903WYDT replacement LM2903WYDT cross reference LM2903WYDT vs LM2903HDT LM2903WYDT footprint LM2903WYDT price LM2903WYDT stock STMicroelectronics LM2903WYDT LM2903 2V 36V comparator LM2903WYDT open collector output LM2903WYDT industrial sensor

قطعات و اصطلاحات مرتبط

STMicroelectronics LM2903WYDT LM2903W LM2903HDT LM2903YDT LM2903B LM2903D Texas Instruments onsemi dual voltage comparator comparator analog integrated circuit interface IC open-collector output single-supply operation split-supply operation 2 V to 36 V supply 0.4 mA power consumption 25 nA input offset voltage 8-pin SOIC SOIC family surface-mount package industrial sensor interface battery-powered monitoring power-good detection
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ