LM358BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
部品番号: LM358BAIDR ✓ 生産中LM358BAIDR 概要
An operational amplifier is an analog signal-processing IC that amplifies the difference between its inverting and non-inverting inputs. The LM358 family belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Unlike a single amplifier package, this dual-device version provides two amplifier channels in one component, reducing board area and simplifying designs that require paired gain, filtering, buffering, or comparison functions.
The LM358BAIDR combines a maximum 36 V supply rating with a 1.2 MHz gain-bandwidth product. Its 2 mV offset voltage is suitable for many general-purpose applications where moderate DC accuracy is acceptable. The 8-SOIC surface-mount package supports conventional PCB assembly, while the -40°C to 85°C operating range covers industrial and commercial environments. Typical rail-to-rail behavior, common-mode limits, supply-current requirements, and output-drive capability should be checked against the manufacturer datasheet for each design.
The two amplifier sections share the power-supply pins but otherwise provide separate inverting and non-inverting inputs and outputs. This arrangement suits cascaded stages, dual sensor channels, error amplifiers, voltage followers, and differential signal-conditioning circuits. Because both channels use the same device, their offset, bandwidth, noise, and common-mode performance are inherently well matched for many balanced systems.
Typical uses include industrial sensor interfaces, buffered control outputs, low-frequency active filters, audio preamplification, power-supply monitoring, and general embedded signal conditioning. It can also support two independent channels in equipment where a quad amplifier would leave unnecessary circuitry. The 1.2 MHz bandwidth is most appropriate for low- and intermediate-frequency signals rather than wideband video or high-speed communications.
When laying out the PCB, route sensitive input and feedback traces away from switching nodes and high-current paths. Place input-rejection and output-bypass capacitors close to their corresponding pins, verify common-mode and output-swing limits at the intended supply voltage, and maintain adequate copper area for thermal dissipation. Confirm the exact SOIC-8 land pattern and pin numbering against the manufacturer pin-description table.
This product page combines the LM358BAIDR ordering information, manufacturer specifications, package details, price reference, pinout status, and technically filtered replacement guidance. It also adds application-oriented design notes and comparison criteria that help engineers determine whether the original device or a qualified drop-in alternative best fits a new board revision.
ドロップイン代替品: LM358BAIDR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM358BAIDR (同一形状・フットプリント) — 相違点: Package, Amplifier Type, Number of Circuits, Number of Amplifier Channels, Product Type.
LM358DR
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →LM358D
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →SGMI8358
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TP358
✅ ドロップイン📋 参考代替品(カタログ未掲載)
BP358
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LM358BAIDR 最大定格&電気的特性
| Product Type | Dual operational amplifier |
| Number of Amplifier Channels | 2 circuits |
| Maximum Supply Voltage | 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Offset Voltage | 2 mV |
| 動作温度範囲 | -40°C to 85°C |
| パッケージ | 8-SOIC |
| 実装タイプ | Surface mount |
LM358BAIDR 8-soic ピン配置ガイド
LM358BAIDR (8-soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LM358BAIDR.
詳細は データシート をご参照ください。
主な用途
LM358BAIDR の用途: 6 件s: Industrial Sensor Signal Conditioning, Low-Frequency Active Filters, Power-Supply Monitoring, Audio Preamplification, Embedded Control and Feedback Loops, General-Purpose Buffering and Comparison.
Industrial Sensor Signal Conditioning
The LM358BAIDR fits two-channel industrial sensor conditioning because it combines two amplifiers in one 8-SOIC package and accepts supply voltages up to 36 V. Each channel can provide gain, inversion, filtering, or buffering before a controller input. The 1.2 MHz gain-bandwidth product is suitable for sensors with moderate bandwidth, while the 2 mV offset voltage supports general-purpose rather than precision-nulling requirements. Check the input common-mode range at the selected supply and keep sensor wiring away from motor and switching nodes to minimize coupled interference.
おすすめ
Low-Frequency Active Filters
The LM358BAIDR is appropriate for first- and second-order low-frequency active-filter stages because its 1.2 MHz gain-bandwidth product provides usable closed-loop bandwidth above typical audio and control-signal frequencies. Two channels allow a Sallen-Key stage and an output buffer to be implemented in one package. The 2 mV offset voltage is acceptable when filter output accuracy requirements are modest. Select external resistor and capacitor values within the amplifier's recommended range, and verify phase margin and component tolerances during simulation.
おすすめ
Power-Supply Monitoring
The LM358BAIDR can monitor a supply rail in industrial or embedded equipment because its 36 V maximum supply rating accommodates higher-voltage monitoring systems. One channel may amplify a scaled divider voltage for comparison with an ADC reference, while the second can buffer the divided rail or drive an indicator. The 1.2 MHz bandwidth is more than sufficient for slow supply changes. Designers must still confirm the common-mode input range, output swing, and input protection at the selected operating voltage.
おすすめ
Audio Preamplification
The LM358BAIDR can serve as a low-frequency audio preamplifier or active volume-control stage because it provides two amplifier channels, a 1.2 MHz gain-bandwidth product, and a 36 V maximum supply rating. The bandwidth supports audio-band signals, although the 2 mV offset voltage may be noticeable in high-gain or quiet designs. Use one channel for gain and the other for output buffering, and place the input and feedback components close to their pins to reduce parasitic pickup and instability risk.
おすすめ
Embedded Control and Feedback Loops
The LM358BAIDR is useful in embedded control loops where two independent amplifiers handle error amplification and feedback buffering. Its dual-channel construction reduces component count compared with two single-amplifier packages, while the 1.2 MHz bandwidth is sufficient for many temperature, position, and actuator-control loops. The 2 mV offset can affect the deadband of a comparator, so evaluate it against the required control accuracy. Confirm loop stability and output-current demand with the actual sensor and actuator impedances.
おすすめ
General-Purpose Buffering and Comparison
The LM358BAIDR supports voltage-follower, comparator, and impedance-buffer functions where two channels are useful and moderate frequency response is sufficient. One channel can buffer a high-impedance source while the other performs threshold comparison or additional gain. The 36 V supply rating gives designers flexibility across industrial and automotive-adjacent control environments, although automotive qualification must not be inferred from the operating range. Confirm output swing and saturation behavior before using the output as a logic-level drive signal.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM358BAIDR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM358DR | LM358D | SGMI8358 | TP358 | BP358 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | SGMC (Sagna Microelectronics) | 3PEAK | YAGEO |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 | 2 |
主な差別化要因
- Confirmed 36 V supply capability in a compact dual-amplifier package (vs SGMI8358)
- Documented 1.2 MHz gain-bandwidth product and 2 mV offset (vs TP358)
- Manufacturer traceability within the established LM358 family (vs BP358)
- Two independent amplifier channels reduce package count (vs LM358DR)
設計ノート
Keep the two input pins, output pins, supply pins, and external compensation or bypass connections close to their intended SOIC-8 land patterns. Place the power-bypass capacitor immediately between the supply and ground pins, and terminate unused amplifier inputs to a defined bias point. A floating input can oscillate and increase supply current even when the other channel is performing normally.
Route high-impedance input and feedback traces as short as practical and keep them away from switching-regulator outputs, relay contacts, motor traces, and other high-current paths. The 1.2 MHz gain-bandwidth product favors low- and intermediate-frequency signals, but high-gain layouts remain sensitive to parasitic capacitance. Use a grounded guard or shielding strategy when a nearby source has high source impedance or when the amplifier is configured with a high closed-loop gain.
Do not treat the 36 V maximum supply rating as an indication that inputs or outputs may swing rail to rail. Before selecting the LM358BAIDR for a new supply voltage, verify input common-mode range, output swing, output-current capability, and stability requirements in the manufacturer datasheet. Also avoid assuming that a 2 mV offset specification guarantees a particular system-level accuracy after gain, temperature, and resistor tolerances are included.
コンプライアンス情報
The verified product summaries identify the LM358BA device and ordering information but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.