Texas Instruments

LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments

部品番号: LM358BIDGKR ✓ 生産中
36 V Vdss 8-VSSOP Package
MOQ: 1 |

LM358BIDGKR 概要

Texas Instruments LM358BIDGKR is a dual operational amplifier in an 8-pin VSSOP package, built for general-purpose signal conditioning from single or dual power supplies. Its headline electrical ratings are a 36 V maximum supply voltage, 1.2 MHz gain-bandwidth product, and 3 mV maximum input offset voltage. The LM358B family combines two amplifiers in one package and supports input common-mode ranges that extend toward ground, making it useful in industrial, instrumentation, control, and sensor-interface circuits.

An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category sits above instrumentation amplifiers and buffers in the broader analog-IC hierarchy, while the dual configuration places two independent amplifiers in one compact surface-mount package. LM358B devices are often selected when moderate bandwidth, wide supply-voltage operation, and input-stage tolerance are more important than low-noise precision performance.

The LM358BIDGKR provides a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. These values support general-purpose closed-loop signal processing, including voltage buffers, cross-coupled amplifiers, differential stages, integrators, and active filtering. Its 3 V to 36 V operating supply range accommodates common industrial and laboratory supply levels. The manufacturer identifies 300 µV as the typical low offset voltage for the LM358B family, while distributor product information lists 3 mV offset voltage for this ordering code.

Because each channel contains an input stage, output stage, and compensation network, LM358B behavior depends on supply voltage, load, output voltage, and common-mode input level. The 1.2 MHz gain-bandwidth product makes the device suitable for moderate-frequency closed-loop gains rather than precision or high-speed applications. Users should account for output-current limits and ensure that the amplifier is not used to source or sink current beyond its specified operating conditions.

Typical uses include 0–10 V industrial sensor interfaces, audio preamplifier and mixing stages, active analog filters, motor and actuator control loops, low-frequency data acquisition, and general sensor conditioning. In a single-supply system, the input common-mode range extending to ground helps process signals centered near 0 V, provided the output swing and input limits are checked against the actual supply voltage.

For PCB design, keep input and feedback traces short, route output signals away from high-impedance inputs, and provide stable bypass capacitance close to the supply pins. Check output drive into the intended load and leave adequate headroom for input and output swing. Decoupling placement and trace geometry can matter more than nominal amplifier bandwidth when working with long routes or high source impedances.

This page combines manufacturer specifications, ordering information, pin-package details, qualified same-family alternatives, and application guidance for faster component selection and board-level planning. It also highlights the practical distinction between the LM358B family's typical offset voltage and the ordering-code maximum used for design margin.

ドロップイン代替品: LM358BIDGKR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: LM358BIDGKR (同一形状・フットプリント) — 相違点: Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Package Type.

Texas Instruments
Amplifier Type: Dual general-purpose operational amplifier
Gain-Bandwidth Product: 700 kHz
Maximum Supply Voltage: 30 V
比較対象 LM358BIDGKR →

LM358ADGKR

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 8-VSSOP (DGK)
Dual general-purpose operational amplifier · 2 channels · 30 V · 700 kHz · 3 mV · 0 °C to +70 °C · VSSOP (DGK) · 8 pins

価格はお問い合わせください

データシートを見る →

LM358BDGKR

✅ ドロップイン ⚠️ 仕様未検証
📦 8-VSSOP (DGK)
Same 36 V maximum supply and 1.2 MHz gain-bandwidth rating, representing 0% difference on those headline parameters; the ordering code denotes a different temperature or grade option.

📋 参考代替品(カタログ未掲載)

LM2904ADGKR

✅ ドロップイン ⚠️ 仕様未検証
📦 8-VSSOP (DGK)
Same dual-amplifier concept, 36 V maximum supply, and 1.2 MHz gain-bandwidth rating, representing 0% difference on those headline parameters; qualification differs by ordering code.

📋 参考代替品(カタログ未掲載)

LM2904BDGKR

✅ ドロップイン ⚠️ 仕様未検証
📦 8-VSSOP (DGK)
Same dual-amplifier concept, 36 V maximum supply, and 1.2 MHz gain-bandwidth rating, representing 0% difference on those headline parameters; qualification differs by ordering code.

📋 参考代替品(カタログ未掲載)

LM358BDGKT

✅ ドロップイン ⚠️ 仕様未検証
📦 8-VSSOP (DGK)
Same 36 V maximum supply, 1.2 MHz gain-bandwidth product, and 8-VSSOP footprint, representing 0% difference on those headline parameters; small reel packing differs.

📋 参考代替品(カタログ未掲載)

LM358BIDGKR 最大定格&電気的特性

Amplifier Type General-purpose operational amplifier
Number of Channels 2 channels
Maximum Supply Voltage 36 V
Operating Supply Voltage Range 3 V to 36 V
Gain-Bandwidth Product 1.2 MHz
Slew Rate 0.5 V/µs
Input Offset Voltage 3 mV
Typical Family Offset Voltage 300 µV
Common-Mode Input Range Extends to ground
Differential Input Voltage Capability High differential input voltage capability
Package Type 8-VSSOP
実装タイプ Surface mount
ESD Protection Improved ESD protection

LM358BIDGKR 8-vssop ピン配置ガイド

LM358BIDGKR (8-vssop パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

LM358BIDGKR の 8-vssop パッケージピン配置図

詳細なピン配置データはありません: LM358BIDGKR.

詳細は データシート をご参照ください。

主な用途

LM358BIDGKR の用途: 6 件s: Industrial 0–10 V Sensor Interface, Audio Preamplifier and Mixer, Active Analog Filter, Motor and Actuator Control, Low-Frequency Data Acquisition, Battery-Powered Monitoring Circuit.

🏭

Industrial 0–10 V Sensor Interface

The LM358BIDGKR fits a 0–10 V process-signal input because its dual channels can provide input buffering and gain-stage amplification within one 8-VSSOP package. Its 3 V to 36 V supply range accommodates common industrial rails, while the input common-mode range extending toward ground supports sensor outputs near the lower rail. The 1.2 MHz gain-bandwidth product is more than adequate for slow process variables and transducer bandwidths. Design the first stage so its output remains within the amplifier's allowed output swing, and place the feedback components close to the pins to minimize parasitic sensitivity. A second channel can provide active filtering or an output driver when the load is moderate.

🎧

Audio Preamplifier and Mixer

LM358BIDGKR can provide separate gain and mixing stages for low-to-moderate-bandwidth audio signals. Its 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate are suitable for common audio-band applications, while the dual configuration saves board area in line-level preamplifiers or small mixers. The amplifier's general-purpose architecture favors economical signal conditioning over very low-noise microphone amplification. Check source impedance, input bias-current error, output loading, and clipping headroom at the selected supply voltage. Keep gain-setting resistors close to the relevant channel and maintain short signal paths to reduce noise pickup and unintended high-frequency feedback.

🔧

Active Analog Filter

The LM358BIDGKR is suitable for first- and second-order active filters handling signals well below its 1.2 MHz gain-bandwidth product. Its two channels permit an Sallen-Key stage and active gain stage to share one package, reducing component count in sensor-conditioning and control boards. The broad 3 V to 36 V supply range supports multiple industrial and laboratory systems, but component tolerances and amplifier gain-bandwidth behavior still affect filter accuracy. Select resistor and capacitor values against the desired cutoff, then verify gain peaking and phase margin on the assembled board. Keep sensitive input and feedback nodes compact and bypass the supply pins to reduce noise coupling into the filter output.

⚡

Motor and Actuator Control

LM358BIDGKR can implement the low-level error-amplifier and control-signal stages of a motor or actuator controller. The 3 V to 36 V supply range permits operation from higher-voltage control systems, and the input common-mode range extending to ground is useful for feedback signals referenced near 0 V. The 0.5 V/µs slew rate and 1.2 MHz bandwidth are suitable for many low-bandwidth feedback loops, but they do not replace the requirements of a high-current driver. Add a separate transistor or power stage for motor excitation. Check the feedback divider, output current, saturation recovery, and stability before closing the control loop because the op-amp does not directly provide motor-drive current.

🖥️

Low-Frequency Data Acquisition

LM358BIDGKR can condition low-frequency sensor and measurement signals before an ADC, with one channel used for amplification and the other for active filtering or reference buffering. Its 1.2 MHz gain-bandwidth product comfortably covers many kilohertz-band acquisition systems, while the common-mode input range extending to ground simplifies single-supply sensor interfaces. Offset error remains a primary concern when amplifying small signals, so use the 300 µV typical family value for an initial estimate and apply the 3 mV ordering-code limit during worst-case error analysis. Verify input bias current, source impedance, ADC input range, and output-swing limits. Place the amplifier close to the protected analog front end and keep digital switching paths physically separated.

🔋

Battery-Powered Monitoring Circuit

LM358BIDGKR can support low-voltage monitoring, current sensing, and threshold functions in battery-operated equipment because its operating supply range starts at 3 V. The dual layout can monitor a sensor on one channel and provide an inverted or complementary signal on the other, while the common-mode input range extending to ground helps with measurements referenced to the negative supply. The device is a linear amplifier rather than a regulator, so power use depends on supply voltage and operating current. Confirm quiescent current and output behavior from the manufacturer datasheet for the intended grade. Keep input bias-current error in the calculation, especially with high-impedance sensor nodes, and avoid placing excessive load on a battery-powered source.

おすすめ製品の概要

LM358BIDGKR Texas Instruments 使用用途: Industrial 0–10 V Sensor Interface, Audio Preamplifier and Mixer, Active Analog Filter, Motor and Actuator Control, Low-Frequency Data Acquisition, Battery-Powered Monitoring Circuit LM358BDGKR Same-family dual amplifier option 使用用途: Industrial 0–10 V Sensor Interface, Low-Frequency Data Acquisition LM2904BDGKR Same-family dual audio amplifier alternative 使用用途: Audio Preamplifier and Mixer, Battery-Powered Monitoring Circuit LM358ADGKR Texas Instruments 使用用途: Active Analog Filter LM2904ADGKR Same-family control amplifier option 使用用途: Motor and Actuator Control
What are the key specifications of LM358BIDGKR that engineers should know?
The LM358BIDGKR is a dual, general-purpose operational amplifier with a 3 V to 36 V supply range, 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and 3 mV listed input offset voltage. Texas Instruments describes the LM358B family as an industry-standard dual op-amp design with a common-mode input range extending to ground and a typical offset of 300 µV. It is packaged in an 8-VSSOP for compact surface-mount analog circuits.
What is the operating voltage of LM358BIDGKR?
The LM358BIDGKR operates from 3 V to 36 V. According to the Texas Instruments LM358B product information, the device includes two operational amplifiers intended for high-voltage, cost-sensitive applications. The wide supply range allows the same device to be used with common low-voltage and industrial-level supplies, although output swing and common-mode input limits still depend on the selected supply voltage.
What is the gain-bandwidth product and slew rate of LM358BIDGKR?
The LM358BIDGKR has a 1.2 MHz gain-bandwidth product and a 0.5 V/µs slew rate. These figures define its useful small-signal bandwidth and large-signal response, respectively. The manufacturer describes the LM358B as a general-purpose amplifier rather than a high-speed or precision device, so stable operation normally centers on closed-loop gains that preserve adequate phase margin at the intended signal frequency.
Where can I download the LM358BIDGKR datasheet PDF?
The official LM358BIDGKR product and datasheet information is available from the Texas Instruments LM358B part-details page. According to the manufacturer product page, the LM358B family provides two 36 V operational amplifiers with a common-mode input range extending toward ground. Use the manufacturer PDF for the authoritative pin descriptions, electrical characteristics, operating limits, and application guidance before finalizing a PCB or high-voltage design.
Where can I find the LM358BIDGKR pinout and package information?
The LM358BIDGKR uses an 8-pin VSSOP package. Use the pin-description table in the Texas Instruments manufacturer datasheet when assigning PCB nets and checking the exposed-pad or thermal requirements. The device contains two operational amplifiers, so the schematic must identify each channel separately. Verify package orientation, pin numbering, and any exposed-pad connection directly against the datasheet before fabrication.
Can LM358BIDGKR be used with a single 5 V supply?
Yes, the LM358BIDGKR can operate from a single 5 V supply because its operating supply range begins at 3 V and extends to 36 V. The common-mode input range extending to ground makes it practical for signals near 0 V, but the output must still remain inside the amplifier's output-swing limits. Check the datasheet curves for input and output headroom at 5 V before selecting the closed-loop gain.
What is the difference between LM358BIDGKR and LM358B?
LM358B is the Texas Instruments family name, while LM358BIDGKR is one specific ordering code in that family. The 8-VSSOP and industrial-grade identifier form part of the orderable designation, distinguishing the exact electrical grade, temperature qualification, and packaging option. For a PCB replacement, compare the complete ordering codes and confirm channel count, supply range, offset limits, pinout, and package rather than comparing only the family name.
Is LM358BIDGKR suitable for industrial sensor interfaces?
Yes, the LM358BIDGKR is well suited to many industrial sensor interfaces because it combines two amplifiers, a 3 V to 36 V supply range, and an input common-mode range extending to ground. It can buffer 0–10 V process signals, amplify low-level sensor outputs, or provide active filtering when signal bandwidth is moderate. For safety-critical equipment, verify the exact temperature grade, isolation requirements, noise performance, and applicable equipment standards separately.
What can replace LM358BIDGKR on the same PCB?
The closest drop-in choices are Texas Instruments LM358ADGKR, LM358BDGKR, LM2904ADGKR, and LM2904BDGKR, subject to electrical-grade and temperature-range verification. These are same-family LM358/LM2904-style dual amplifiers in the corresponding 8-VSSOP ordering format and are listed as LLM-sourced alternatives. Before replacement, compare the complete datasheet rows for offset voltage, bias current, output drive, common-mode limits, and qualification.
When should I choose LM358BIDGKR over LM2904ADGKR?
Choose LM358BIDGKR when the design specifically calls for the LM358B industrial-grade ordering family and its characterized behavior. Choose LM2904ADGKR only after checking whether the automotive temperature grade and electrical limits are appropriate for the installation. Both are dual general-purpose op-amp concepts with similar package families, but the exact suffix determines qualification, temperature range, and shipment configuration.
Is LM358BIDGKR suitable for audio preamplifier applications?
Yes, LM358BIDGKR can be used in many audio preamplifier and mixing stages where moderate bandwidth and low cost are more important than very low noise. Its 1.2 MHz gain-bandwidth product is sufficient for many audio-frequency signal paths, while the dual layout provides independent channels. A high-gain microphone stage may require additional input and output impedance analysis and consideration of a lower-noise preamplifier.
What is the best 3PEAK equivalent for LM358BIDGKR?
A specific 3PEAK drop-in equivalent cannot be confirmed from the available component-level cross-reference results, because the cited article names the manufacturer but does not identify a complete ordering code or package. Do not substitute an 8-pin device based on the LM358 name alone. Select a 3PEAK part only after its manufacturer datasheet confirms the 8-VSSOP footprint, pin assignments, supply range, offset voltage, output drive, and temperature qualification.
How much power does LM358BIDGKR dissipate at 12 V?
LM358BIDGKR dissipation depends on supply voltage, output voltage, load current, and each channel's operating state. The device is a linear amplifier, so unused quiescent current still creates internal loss. Use the manufacturer quiescent-current and output-current specifications for a complete calculation. Request the exact datasheet values through the Request a Quote form if they are needed for a documented thermal design.
Where to buy LM358BIDGKR online?
Use the Request a Quote form on this page to request LM358BIDGKR availability, current lead time, and ordering confirmation from XAIPART. The exact orderable code is LM358BIDGKR in an 8-VSSOP package, so include the complete MPN in the request. This avoids confusion with other LM358 temperature grades, package variants, or equivalent devices that may not be pin-compatible.
What is the price of LM358BIDGKR?
Use the Request a Quote form on this page for the current LM358BIDGKR price and quantity pricing. Pricing changes with quantity, market conditions, and packaging requirements, so the structured price table should not be copied into engineering documentation. When requesting a quote, specify the required quantity, package packing preference, production schedule, and destination.
What is the lead time and stock status for LM358BIDGKR?
The current lead time and stock status for LM358BIDGKR should be confirmed through the Request a Quote form on this page. Include your required order quantity, target delivery date, and production schedule in the request. The component is an 8-VSSOP dual op-amp ordering code, so confirm the complete suffix and packing method as part of the order review.

エンジニアリング参考データ: LM358BIDGKR — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose LM358BIDGKR when the design requires a dual general-purpose op-amp with a 3 V to 36 V supply range, approximately 1.2 MHz gain-bandwidth product, and an 8-VSSOP footprint. It is a sensible fit for industrial sensor interfaces, active filters, audio preamplification, low-frequency data acquisition, and control-signal conditioning. Select LM358ADGKR when its corresponding qualification is preferred, LM358BDGKR when that grade matches the installation better, and LM358BDGKT when its small-reel shipment configuration is preferred. Consider LM2904ADGKR or LM2904BDGKR when their LM2904 ordering and qualification characteristics better match the product. For every candidate, verify the complete ordering code, temperature range, offset voltage, bias current, output drive, common-mode limits, exposed-pad treatment, and lifecycle status against the manufacturer datasheet.

代替品との比較

パラメータ この製品 LM358ADGKR LM358BDGKR LM2904ADGKR LM2904BDGKR LM358BDGKT
Package 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Channels 2 2 2 2 2 2
Maximum Supply Voltage 36 V 36 V 36 V 36 V 36 V 36 V
Gain-Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz

主な差別化要因

  • Combines two general-purpose amplifiers with wide supply capability in one compact package (vs LM358ADGKR)
  • Industrial LM358B ordering option supports general-purpose analog designs (vs LM2904ADGKR)
  • Eight-pin VSSOP integration reduces footprint without sacrificing dual-channel functionality (vs LM358BDGKT)

設計ノート

Place the supply bypass capacitor directly between the supply and ground pins. Keep input, feedback, and output paths short, especially for high-gain configurations, and avoid routing output traces parallel to sensitive input traces. If the exposed pad is electrically connected, follow the manufacturer land-pattern and thermal-pad guidance rather than treating the 8-VSSOP as a simple eight-lead footprint.

Do not assume that a common-mode range extending to ground guarantees an output that can reach ground perfectly. Check the output-swing limits for the selected supply voltage and load current. Likewise, a 1.2 MHz gain-bandwidth product does not mean the circuit is stable at every closed-loop gain or with every capacitive load. Validate the intended gain, load, and supply configuration against the manufacturer characterization curves.

For source impedances above a few tens of kilohms, calculate the input-bias-current error and compare it with the sensor signal. Use the lowest practical source impedance or add a biasing resistor when appropriate. For sensor-cable interfaces, use guarded or shielded routing, a nearby input reference, and filtering that does not overload the amplifier's drive capability.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The available product information does not explicitly state the individual compliance status of LM358BIDGKR. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and qualification declarations from the manufacturer product documentation.

データ検証日: 2026-11-09 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

LM358BIDGKR datasheet LM358BIDGKR pinout LM358BIDGKR datasheet pdf LM358BIDGKR equivalent LM358BIDGKR replacement LM358BIDGKR cross reference LM358BIDGKR application circuit LM358BIDGKR 8-VSSOP LM358BIDGKR price LM358BIDGKR stock Texas Instruments LM358BIDGKR LM358BIDGKR vs LM358BDGKR LM358BIDGKR 36V 1.2MHz LM358BIDGKR industrial sensor interface

関連部品&用語

Texas Instruments LM358BIDGKR LM358B LM358ADGKR LM358BDGKR LM2904ADGKR LM2904BDGKR LM358BDGKT operational amplifier dual operational amplifier general-purpose amplifier analog signal-conditioning IC instrumentation amplifier buffer amplifier gain-bandwidth product slew rate input offset voltage common-mode input range differential input voltage single-supply operation 8-VSSOP DGK package surface mount active filter industrial sensor interface audio preamplifier data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示