LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments
MPN: LM358BIDGKR ✓ Hoạt độngLM358BIDGKR Tóm tắt
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category sits above instrumentation amplifiers and buffers in the broader analog-IC hierarchy, while the dual configuration places two independent amplifiers in one compact surface-mount package. LM358B devices are often selected when moderate bandwidth, wide supply-voltage operation, and input-stage tolerance are more important than low-noise precision performance.
The LM358BIDGKR provides a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. These values support general-purpose closed-loop signal processing, including voltage buffers, cross-coupled amplifiers, differential stages, integrators, and active filtering. Its 3 V to 36 V operating supply range accommodates common industrial and laboratory supply levels. The manufacturer identifies 300 µV as the typical low offset voltage for the LM358B family, while distributor product information lists 3 mV offset voltage for this ordering code.
Because each channel contains an input stage, output stage, and compensation network, LM358B behavior depends on supply voltage, load, output voltage, and common-mode input level. The 1.2 MHz gain-bandwidth product makes the device suitable for moderate-frequency closed-loop gains rather than precision or high-speed applications. Users should account for output-current limits and ensure that the amplifier is not used to source or sink current beyond its specified operating conditions.
Typical uses include 0–10 V industrial sensor interfaces, audio preamplifier and mixing stages, active analog filters, motor and actuator control loops, low-frequency data acquisition, and general sensor conditioning. In a single-supply system, the input common-mode range extending to ground helps process signals centered near 0 V, provided the output swing and input limits are checked against the actual supply voltage.
For PCB design, keep input and feedback traces short, route output signals away from high-impedance inputs, and provide stable bypass capacitance close to the supply pins. Check output drive into the intended load and leave adequate headroom for input and output swing. Decoupling placement and trace geometry can matter more than nominal amplifier bandwidth when working with long routes or high source impedances.
This page combines manufacturer specifications, ordering information, pin-package details, qualified same-family alternatives, and application guidance for faster component selection and board-level planning. It also highlights the practical distinction between the LM358B family's typical offset voltage and the ordering-code maximum used for design margin.
Bộ thay thế dễ dàng lắp đặt cho LM358BIDGKR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM358BIDGKR (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Package Type.
LM358ADGKR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM358BDGKR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM2904ADGKR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM2904BDGKR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM358BDGKT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM358BIDGKR Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 36 V |
| Operating Supply Voltage Range | 3 V to 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Input Offset Voltage | 3 mV |
| Typical Family Offset Voltage | 300 µV |
| Common-Mode Input Range | Extends to ground |
| Differential Input Voltage Capability | High differential input voltage capability |
| Package Type | 8-VSSOP |
| Kiểu lắp đặt | Surface mount |
| ESD Protection | Improved ESD protection |
Hướng dẫn cấu hình chân LM358BIDGKR 8-vssop
Cấu hình chân cho LM358BIDGKR (8-vssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM358BIDGKR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM358BIDGKR phù hợp cho 6 Áp dụngs: Industrial 0–10 V Sensor Interface, Audio Preamplifier and Mixer, Active Analog Filter, Motor and Actuator Control, Low-Frequency Data Acquisition, Battery-Powered Monitoring Circuit.
Industrial 0–10 V Sensor Interface
The LM358BIDGKR fits a 0–10 V process-signal input because its dual channels can provide input buffering and gain-stage amplification within one 8-VSSOP package. Its 3 V to 36 V supply range accommodates common industrial rails, while the input common-mode range extending toward ground supports sensor outputs near the lower rail. The 1.2 MHz gain-bandwidth product is more than adequate for slow process variables and transducer bandwidths. Design the first stage so its output remains within the amplifier's allowed output swing, and place the feedback components close to the pins to minimize parasitic sensitivity. A second channel can provide active filtering or an output driver when the load is moderate.
Được đề xuất
Audio Preamplifier and Mixer
LM358BIDGKR can provide separate gain and mixing stages for low-to-moderate-bandwidth audio signals. Its 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate are suitable for common audio-band applications, while the dual configuration saves board area in line-level preamplifiers or small mixers. The amplifier's general-purpose architecture favors economical signal conditioning over very low-noise microphone amplification. Check source impedance, input bias-current error, output loading, and clipping headroom at the selected supply voltage. Keep gain-setting resistors close to the relevant channel and maintain short signal paths to reduce noise pickup and unintended high-frequency feedback.
Được đề xuất
Active Analog Filter
The LM358BIDGKR is suitable for first- and second-order active filters handling signals well below its 1.2 MHz gain-bandwidth product. Its two channels permit an Sallen-Key stage and active gain stage to share one package, reducing component count in sensor-conditioning and control boards. The broad 3 V to 36 V supply range supports multiple industrial and laboratory systems, but component tolerances and amplifier gain-bandwidth behavior still affect filter accuracy. Select resistor and capacitor values against the desired cutoff, then verify gain peaking and phase margin on the assembled board. Keep sensitive input and feedback nodes compact and bypass the supply pins to reduce noise coupling into the filter output.
Được đề xuất
Motor and Actuator Control
LM358BIDGKR can implement the low-level error-amplifier and control-signal stages of a motor or actuator controller. The 3 V to 36 V supply range permits operation from higher-voltage control systems, and the input common-mode range extending to ground is useful for feedback signals referenced near 0 V. The 0.5 V/µs slew rate and 1.2 MHz bandwidth are suitable for many low-bandwidth feedback loops, but they do not replace the requirements of a high-current driver. Add a separate transistor or power stage for motor excitation. Check the feedback divider, output current, saturation recovery, and stability before closing the control loop because the op-amp does not directly provide motor-drive current.
Được đề xuất
Low-Frequency Data Acquisition
LM358BIDGKR can condition low-frequency sensor and measurement signals before an ADC, with one channel used for amplification and the other for active filtering or reference buffering. Its 1.2 MHz gain-bandwidth product comfortably covers many kilohertz-band acquisition systems, while the common-mode input range extending to ground simplifies single-supply sensor interfaces. Offset error remains a primary concern when amplifying small signals, so use the 300 µV typical family value for an initial estimate and apply the 3 mV ordering-code limit during worst-case error analysis. Verify input bias current, source impedance, ADC input range, and output-swing limits. Place the amplifier close to the protected analog front end and keep digital switching paths physically separated.
Được đề xuất
Battery-Powered Monitoring Circuit
LM358BIDGKR can support low-voltage monitoring, current sensing, and threshold functions in battery-operated equipment because its operating supply range starts at 3 V. The dual layout can monitor a sensor on one channel and provide an inverted or complementary signal on the other, while the common-mode input range extending to ground helps with measurements referenced to the negative supply. The device is a linear amplifier rather than a regulator, so power use depends on supply voltage and operating current. Confirm quiescent current and output behavior from the manufacturer datasheet for the intended grade. Keep input bias-current error in the calculation, especially with high-impedance sensor nodes, and avoid placing excessive load on a battery-powered source.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM358BIDGKR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM358ADGKR | LM358BDGKR | LM2904ADGKR | LM2904BDGKR | LM358BDGKT |
|---|---|---|---|---|---|---|
| Package | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
Bảo phân biệt quan trọng
- Combines two general-purpose amplifiers with wide supply capability in one compact package (vsLM358ADGKR)
- Industrial LM358B ordering option supports general-purpose analog designs (vsLM2904ADGKR)
- Eight-pin VSSOP integration reduces footprint without sacrificing dual-channel functionality (vsLM358BDGKT)
Ghi chú thiết kế
Place the supply bypass capacitor directly between the supply and ground pins. Keep input, feedback, and output paths short, especially for high-gain configurations, and avoid routing output traces parallel to sensitive input traces. If the exposed pad is electrically connected, follow the manufacturer land-pattern and thermal-pad guidance rather than treating the 8-VSSOP as a simple eight-lead footprint.
Do not assume that a common-mode range extending to ground guarantees an output that can reach ground perfectly. Check the output-swing limits for the selected supply voltage and load current. Likewise, a 1.2 MHz gain-bandwidth product does not mean the circuit is stable at every closed-loop gain or with every capacitive load. Validate the intended gain, load, and supply configuration against the manufacturer characterization curves.
For source impedances above a few tens of kilohms, calculate the input-bias-current error and compare it with the sensor signal. Use the lowest practical source impedance or add a biasing resistor when appropriate. For sensor-cable interfaces, use guarded or shielded routing, a nearby input reference, and filtering that does not overload the amplifier's drive capability.
Thông tin tuân thủ
The available product information does not explicitly state the individual compliance status of LM358BIDGKR. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and qualification declarations from the manufacturer product documentation.