LM358BIDGKR - 36V 1.2MHz Dual Op Amp | Texas Instruments
부품 번호: LM358BIDGKR ✓ 활성LM358BIDGKR 개요
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category sits above instrumentation amplifiers and buffers in the broader analog-IC hierarchy, while the dual configuration places two independent amplifiers in one compact surface-mount package. LM358B devices are often selected when moderate bandwidth, wide supply-voltage operation, and input-stage tolerance are more important than low-noise precision performance.
The LM358BIDGKR provides a 1.2 MHz gain-bandwidth product and a slew rate of 0.5 V/µs. These values support general-purpose closed-loop signal processing, including voltage buffers, cross-coupled amplifiers, differential stages, integrators, and active filtering. Its 3 V to 36 V operating supply range accommodates common industrial and laboratory supply levels. The manufacturer identifies 300 µV as the typical low offset voltage for the LM358B family, while distributor product information lists 3 mV offset voltage for this ordering code.
Because each channel contains an input stage, output stage, and compensation network, LM358B behavior depends on supply voltage, load, output voltage, and common-mode input level. The 1.2 MHz gain-bandwidth product makes the device suitable for moderate-frequency closed-loop gains rather than precision or high-speed applications. Users should account for output-current limits and ensure that the amplifier is not used to source or sink current beyond its specified operating conditions.
Typical uses include 0–10 V industrial sensor interfaces, audio preamplifier and mixing stages, active analog filters, motor and actuator control loops, low-frequency data acquisition, and general sensor conditioning. In a single-supply system, the input common-mode range extending to ground helps process signals centered near 0 V, provided the output swing and input limits are checked against the actual supply voltage.
For PCB design, keep input and feedback traces short, route output signals away from high-impedance inputs, and provide stable bypass capacitance close to the supply pins. Check output drive into the intended load and leave adequate headroom for input and output swing. Decoupling placement and trace geometry can matter more than nominal amplifier bandwidth when working with long routes or high source impedances.
This page combines manufacturer specifications, ordering information, pin-package details, qualified same-family alternatives, and application guidance for faster component selection and board-level planning. It also highlights the practical distinction between the LM358B family's typical offset voltage and the ordering-code maximum used for design margin.
드롭인 대체품: LM358BIDGKR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM358BIDGKR (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Package Type.
LM358ADGKR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM358BDGKR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2904ADGKR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2904BDGKR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM358BDGKT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM358BIDGKR 최대 정격 & 전기적 특성
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 36 V |
| Operating Supply Voltage Range | 3 V to 36 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Input Offset Voltage | 3 mV |
| Typical Family Offset Voltage | 300 µV |
| Common-Mode Input Range | Extends to ground |
| Differential Input Voltage Capability | High differential input voltage capability |
| Package Type | 8-VSSOP |
| 실장 유형 | Surface mount |
| ESD Protection | Improved ESD protection |
LM358BIDGKR 8-vssop 핀 구성 가이드
LM358BIDGKR(8-vssop 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM358BIDGKR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM358BIDGKR 적합 용도: 6 애플리케이션s: Industrial 0–10 V Sensor Interface, Audio Preamplifier and Mixer, Active Analog Filter, Motor and Actuator Control, Low-Frequency Data Acquisition, Battery-Powered Monitoring Circuit.
Industrial 0–10 V Sensor Interface
The LM358BIDGKR fits a 0–10 V process-signal input because its dual channels can provide input buffering and gain-stage amplification within one 8-VSSOP package. Its 3 V to 36 V supply range accommodates common industrial rails, while the input common-mode range extending toward ground supports sensor outputs near the lower rail. The 1.2 MHz gain-bandwidth product is more than adequate for slow process variables and transducer bandwidths. Design the first stage so its output remains within the amplifier's allowed output swing, and place the feedback components close to the pins to minimize parasitic sensitivity. A second channel can provide active filtering or an output driver when the load is moderate.
추천
Audio Preamplifier and Mixer
LM358BIDGKR can provide separate gain and mixing stages for low-to-moderate-bandwidth audio signals. Its 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate are suitable for common audio-band applications, while the dual configuration saves board area in line-level preamplifiers or small mixers. The amplifier's general-purpose architecture favors economical signal conditioning over very low-noise microphone amplification. Check source impedance, input bias-current error, output loading, and clipping headroom at the selected supply voltage. Keep gain-setting resistors close to the relevant channel and maintain short signal paths to reduce noise pickup and unintended high-frequency feedback.
추천
Active Analog Filter
The LM358BIDGKR is suitable for first- and second-order active filters handling signals well below its 1.2 MHz gain-bandwidth product. Its two channels permit an Sallen-Key stage and active gain stage to share one package, reducing component count in sensor-conditioning and control boards. The broad 3 V to 36 V supply range supports multiple industrial and laboratory systems, but component tolerances and amplifier gain-bandwidth behavior still affect filter accuracy. Select resistor and capacitor values against the desired cutoff, then verify gain peaking and phase margin on the assembled board. Keep sensitive input and feedback nodes compact and bypass the supply pins to reduce noise coupling into the filter output.
추천
Motor and Actuator Control
LM358BIDGKR can implement the low-level error-amplifier and control-signal stages of a motor or actuator controller. The 3 V to 36 V supply range permits operation from higher-voltage control systems, and the input common-mode range extending to ground is useful for feedback signals referenced near 0 V. The 0.5 V/µs slew rate and 1.2 MHz bandwidth are suitable for many low-bandwidth feedback loops, but they do not replace the requirements of a high-current driver. Add a separate transistor or power stage for motor excitation. Check the feedback divider, output current, saturation recovery, and stability before closing the control loop because the op-amp does not directly provide motor-drive current.
추천
Low-Frequency Data Acquisition
LM358BIDGKR can condition low-frequency sensor and measurement signals before an ADC, with one channel used for amplification and the other for active filtering or reference buffering. Its 1.2 MHz gain-bandwidth product comfortably covers many kilohertz-band acquisition systems, while the common-mode input range extending to ground simplifies single-supply sensor interfaces. Offset error remains a primary concern when amplifying small signals, so use the 300 µV typical family value for an initial estimate and apply the 3 mV ordering-code limit during worst-case error analysis. Verify input bias current, source impedance, ADC input range, and output-swing limits. Place the amplifier close to the protected analog front end and keep digital switching paths physically separated.
추천
Battery-Powered Monitoring Circuit
LM358BIDGKR can support low-voltage monitoring, current sensing, and threshold functions in battery-operated equipment because its operating supply range starts at 3 V. The dual layout can monitor a sensor on one channel and provide an inverted or complementary signal on the other, while the common-mode input range extending to ground helps with measurements referenced to the negative supply. The device is a linear amplifier rather than a regulator, so power use depends on supply voltage and operating current. Confirm quiescent current and output behavior from the manufacturer datasheet for the intended grade. Keep input bias-current error in the calculation, especially with high-impedance sensor nodes, and avoid placing excessive load on a battery-powered source.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM358BIDGKR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM358ADGKR | LM358BDGKR | LM2904ADGKR | LM2904BDGKR | LM358BDGKT |
|---|---|---|---|---|---|---|
| Package | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) | 8-VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
주요 차별점
- Combines two general-purpose amplifiers with wide supply capability in one compact package (vs LM358ADGKR)
- Industrial LM358B ordering option supports general-purpose analog designs (vs LM2904ADGKR)
- Eight-pin VSSOP integration reduces footprint without sacrificing dual-channel functionality (vs LM358BDGKT)
설계 노트
Place the supply bypass capacitor directly between the supply and ground pins. Keep input, feedback, and output paths short, especially for high-gain configurations, and avoid routing output traces parallel to sensitive input traces. If the exposed pad is electrically connected, follow the manufacturer land-pattern and thermal-pad guidance rather than treating the 8-VSSOP as a simple eight-lead footprint.
Do not assume that a common-mode range extending to ground guarantees an output that can reach ground perfectly. Check the output-swing limits for the selected supply voltage and load current. Likewise, a 1.2 MHz gain-bandwidth product does not mean the circuit is stable at every closed-loop gain or with every capacitive load. Validate the intended gain, load, and supply configuration against the manufacturer characterization curves.
For source impedances above a few tens of kilohms, calculate the input-bias-current error and compare it with the sensor signal. Use the lowest practical source impedance or add a biasing resistor when appropriate. For sensor-cable interfaces, use guarded or shielded routing, a nearby input reference, and filtering that does not overload the amplifier's drive capability.
규정 준수 정보
The available product information does not explicitly state the individual compliance status of LM358BIDGKR. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and qualification declarations from the manufacturer product documentation.