LM393DGKR - Dual 36V Comparator | Texas Instruments
部品番号: LM393DGKR ✓ 生産中LM393DGKR 概要
A differential comparator is a semiconductor that evaluates two input voltages and changes its output state according to their relationship. The LM393 belongs to the comparator hierarchy within analog integrated circuits and interface ICs. It accepts single-supply operation from 2 V to 36 V and also supports dual-supply operation when the total supply span is between 2 V and 36 V. Under dual-supply conditions, the supply connected to VCC must be at least 1.5 V more positive than the input common-mode voltage.
The two independent comparator channels provide flexibility for window detection, threshold switching, overvoltage detection, and simple control-loop sensing. Their open-collector outputs require an external pull-up resistor, but this output architecture also permits several outputs to share a common pull-up and form a wired-AND function. The target part is offered in the compact 8-VSSOP package identified by the DGK ordering code, with the KR suffix denoting the manufacturer’s standard reel-oriented ordering configuration.
Each channel compares its two differential inputs and controls one open-collector output transistor. Because the channels are independent, they can be used for unrelated measurements or together for window comparison. The manufacturer datasheet identifies the LM393 as a dual differential comparator designed for broad supply-voltage operation. The B-generation family also provides lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved ESD performance and input ruggedness compared with the original LM393 family.
Typical uses include detecting an overvoltage or undervoltage condition in a power supply, comparing a sensor signal against a reference voltage, generating a fault flag for industrial equipment, and providing threshold logic for consumer or industrial control boards. Because the outputs are open collector, pull-up resistors are needed to establish a valid high output voltage, and the pull-up voltage should remain compatible with the downstream logic.
The primary design consideration is to verify input common-mode range, supply voltage, output pull-up voltage, and propagation delay for the exact operating point. Keep the comparator inputs away from switching-node copper where possible, use a stable reference for threshold comparisons, and provide a low-impedance ground return. The 8-VSSOP footprint also requires layout that follows the manufacturer’s recommended land pattern and thermal-copper guidance.
This page combines the LM393DGKR operating limits, package and pin assignment, application guidance, drop-in alternatives, and practical design considerations to support faster component selection and PCB implementation.
ドロップイン代替品: LM393DGKR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM393DGKR (同一形状・フットプリント) — 相違点: Package, Comparator Type, Common-Mode Input Range, Supply Configuration, Output Type.
LM393LVQDGKRQ1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LM393DGKR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM393DG
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM393DGKR 最大定格&電気的特性
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 independent channels |
| Single-Supply Operating Voltage | 2 V to 36 V |
| Dual-Supply Total Voltage Span | 2 V to 36 V |
| Dual-Supply VCC-to-Input Common-Mode Requirement | VCC at least 1.5 V more positive than input common-mode voltage |
| 出力タイプ | Open collector |
| Input Configuration | Differential inputs on each channel |
| パッケージ | 8-VSSOP |
| ピン数 | 8 pins |
| 実装タイプ | Surface mount |
| Commercial Temperature Grade | Commercial grade |
| RoHS ステータス | Compliant |
| MSL | Level 1, 260 C unlimited floor life |
LM393DGKR ピン構成
| ピン 1 | OUT 1 — Open-collector output for comparator channel 1 |
| ピン 2 | IN 1− — Inverting input for comparator channel 1 |
| ピン 3 | IN 1+ — Non-inverting input for comparator channel 1 |
| ピン 4 | GND — Ground connection shared by both comparator channels |
| ピン 5 | IN 2+ — Non-inverting input for comparator channel 2 |
| ピン 6 | IN 2− — Inverting input for comparator channel 2 |
| ピン 7 | OUT 2 — Open-collector output for comparator channel 2 |
| ピン 8 | VCC — Positive supply connection shared by both comparator channels |
主な用途
LM393DGKR の用途: 6 件s: Industrial Overvoltage Detection, Power-Supply Window Monitor, Sensor Signal Conditioning, Automotive and Battery System Interfacing, Consumer Equipment Fault Flagging, Data Conversion and Limit Detection.
Industrial Overvoltage Detection
LM393DGKR fits industrial overvoltage detection because its 2 V to 36 V single-supply range covers common 12 V and 24 V control rails. One channel can compare a divided monitor voltage against a precision reference, then use the open-collector output to pull a fault line low. The two channels allow separate overvoltage and undervoltage thresholds. A suitable pull-up resistor establishes the logic-high state, while divider resistors keep the comparator input within its common-mode range. Designers should account for input offset and propagation delay when defining a protection threshold, and confirm the exact reference and output timing against the manufacturer datasheet before production release.
おすすめ
Power-Supply Window Monitor
LM393DGKR can implement a power-supply window monitor using its two independent differential comparator channels. One channel detects operation below a lower threshold and the other detects operation above an upper threshold. The open-collector outputs can share a pull-up to create a wired-AND fault indication, reducing the number of external logic nodes required by the controller. Its wide 2 V to 36 V supply range is especially useful for monitoring higher-voltage industrial rails. The divider ratio must preserve valid input common-mode operation, and the selected pull-up must satisfy both downstream logic levels and the required fault-response timing.
おすすめ
Sensor Signal Conditioning
LM393DGKR is appropriate for converting a sensor-derived analog level into a digital threshold event. A resistive divider or sensor network drives the non-inverting input, while a stable reference drives the inverting input; the open-collector output then indicates whether the measured signal has crossed the selected threshold. Because the two channels are independent, one device can support either complementary sensing or two related measurements. The 2 V to 36 V operating range provides flexibility in industrial and embedded systems. Keep the reference node quiet, route sensor traces away from switching nodes, and select pull-up resistance to balance signal rise time with power consumption and output-current capability.
おすすめ
Automotive and Battery System Interfacing
LM393DGKR can be used in non-qualified battery-system interface circuits where a wide supply range and open-collector fault signaling are useful. It can compare a scaled battery voltage against a reference to indicate an out-of-range condition, while the second channel handles another polarity or threshold. The 2 V to 36 V range covers many 12 V automotive and industrial battery-derived rails, but the commercial-grade LM393 is not itself identified as an AEC-Q100-qualified alternative. Automotive programs must therefore verify qualification, temperature limits, ESD performance, and production-part requirements separately rather than assuming this ordering code meets automotive specifications.
おすすめ
Consumer Equipment Fault Flagging
LM393DGKR provides a straightforward open-collector fault flag for consumer equipment that monitors an internal rail, temperature proxy, or sensor level. Because the output can sink current and remain open when inactive, it can directly interface with an enable, reset, or status input on another device. Two independent channels allow separate alarm and ready indications without requiring two comparator packages. The 8-VSSOP format helps conserve board area, although exposed-pad or lead-frame thermal details must follow the exact package drawing. Select a pull-up voltage compatible with the receiving logic and verify that every monitored input remains inside the valid common-mode range.
おすすめ
Data Conversion and Limit Detection
LM393DGKR can serve as a high-side or low-side limit detector around an analog signal-processing chain. The differential inputs compare an incoming voltage with a local reference, and the open-collector output indicates whether the signal is within the expected range. Its wide operating supply range permits use in systems where signal amplitudes and supply rails vary across industrial boards. For accurate acquisition systems, keep the comparator reference quieter than the sensed signal and account for offset voltage and propagation delay in the sampling architecture. The pull-up network should be designed to produce a clean transition at the connected ADC, logic gate, or protection input without excessive capacitive loading.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM393DGKR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM393LVQDGKRQ1 | LM393DGKR | LM393DG |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor | Texas Instruments |
| Package | 8-VSSOP | 8-VSSOP | 8-VSSOP | 8-VSSOP |
| Comparator Configuration | Dual differential | Dual differential | Dual differential | Dual differential |
| Number of Independent Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Single-Supply Operating Range | 2 V to 36 V | Up to 5 V | 2 V to 36 V | 2 V to 36 V |
主な差別化要因
- Supports a substantially wider single-supply range than the LV alternative (vs LM393LVQDGKRQ1)
- Cross-brand ordering code retains the same dual open-collector architecture and 8-VSSOP format (vs ROHM Semiconductor LM393DGKR)
- Avoids the power-on-reset feature of the LV family when a simple commercial-grade comparator is preferred (vs LM393LVQDGKRQ1)
設計ノート
Do not treat the open-collector output as a push-pull logic output. Each channel requires a pull-up resistor to establish a high voltage, and the resistor must be selected so the output can sink the required current in its low state while still producing an acceptable rise time at the receiving logic. If multiple outputs share a common pull-up, verify the worst-case combined sink current and ensure that no output pulls the shared node below its valid logic-low threshold.
Validate the VCC rail and dual-supply common-mode condition for the exact operating point. According to the Texas Instruments manufacturer datasheet, the total supply span for dual-supply operation must remain between 2 V and 36 V, and VCC must be at least 1.5 V more positive than the input common-mode voltage. A 12 V supply can be valid for some input ranges but invalid when the compared signal approaches the positive rail, so include worst-case signal and supply tolerances.
Follow the manufacturer’s 8-VSSOP land pattern and place input and pull-up components close to the associated pins. Route the two comparator inputs as short, quiet traces, keep them away from switching-node copper, and provide a direct ground return. Because the two channels share VCC and GND, poor supply or ground routing can couple noise into both comparisons even when the input dividers are correctly designed.
コンプライアンス情報
RoHS compliance and MSL Level 1 at 260 C unlimited floor life are stated for LM393DGKR. The remaining compliance fields are unknown because no explicit conclusions for them are stated. The automotive LM393LVQDGKRQ1 alternative is identified as a Q1 device, but that qualification does not apply to the commercial-grade LM393DGKR.