LT8640IUDC-1 - 42V, 5A Sync Buck Silent Switcher | Analog Devices
部品番号: LT8640IUDC-1 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.59 | $9.59 |
| 10 | $8.62 | $86.20 |
| 100 | $7.31 | $731.00 |
| 500 | $6.41 | $3,205.00 |
| 1,000 | $5.74 | $5,740.00 |
LT8640IUDC-1 概要
An LDO (low-dropout linear regulator) and buck (step-down) DC-DC converter are two distinct topologies in the power-management IC family tree. Both belong to the broader category of voltage regulators, but an LDO uses a series pass element to dissipate VIN-VOUT as heat, while a buck converter switches an inductor to deliver power with much higher efficiency. The LT8640IUDC-1 is a monolithic synchronous buck converter that integrates the high-side and low-side MOSFETs, eliminating the external Schottky diode typical of older buck designs and reducing BOM count.
Key features of the LT8640IUDC-1 include Analog Devices' Silent Switcher architecture, which minimizes EMI emissions by containing the high-dV/dt switching node loops, enabling compliance with CISPR 224 likely-class radiated and conducted limits without a shield. It delivers 5A continuous output at high efficiency, has a 30ns minimum on-time that allows high-frequency step-down at high VIN to low VOUT, and offers Burst Mode operation, spread-spectrum modulation, and external clock synchronization through the SYNC/MODE pin. The -1 suffix designates forced-continuous operation, in contrast to the standard LT8640 which uses pulse-skipping at light loads.
The LT8640IUDC-1 is particularly well-suited to automotive and industrial applications where the input rail can see load-dump transients up to 42V and where EMI compliance is critical. Typical use cases include 24V industrial sensor rails, automotive infotainment, point-of-load supplies downstream of a 12V or 24V bus, and battery-powered systems where 2.5µA quiescent current dramatically extends standby life. A 10µF minimum output capacitor with low ESR is required to keep the control loop stable.
When designing with this part, ensure the input capacitor is ceramic and placed close to the VIN and PGND pads, and that the exposed pad is soldered to a sufficiently large copper pour for thermal dissipation - at 5A load with large VIN-VOUT, the LT8640IUDC-1 can dissipate several watts. This page synthesizes distributor pricing, drop-in alternatives including the AEC-Q100 automotive-grade variant and the 3.5A 65V LT8641, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: LT8640IUDC-1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LT8640IUDC-1 （同一形状・フットプリント） — 相違点: Architecture, Operating Junction Temperature, Package, Quiescent Current, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
LT8640IUDC#PBF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
LT8640IUDC-1#TRPBF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
LT8640EUDC#TRPBF
✅ ドロップイン✓ 在庫あり
$5.48 / 個
データシートを見る →LT8640EUDC-1#TRPBF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
LT8641HUDC#PBF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
LT8640IUDC-1 最大定格＆電気的特性
| トポロジー | Synchronous Buck (Step-Down) |
| 入力電圧範囲 | 3.4 V to 42 V |
| 出力電圧範囲 | 0.97 V to 41.58 V (adjustable) |
| 最大出力電流 | 5 A |
| スイッチング周波数 | 200 kHz to 3 MHz (programmable) |
| 静止電流 | 2.5 µA (Burst Mode, output in regulation) |
| Architecture | Silent Switcher (integrated MOSFETs) |
| Minimum Top Switch On-Time | 30 ns |
| Light-Load Operation | Forced continuous mode (LT8640-1) |
| SYNC/MODE Pin Functions | Burst Mode, spread spectrum, external SYNC, forced CCM |
| 動作接合温度 | -40 °C to +125 °C (I grade) |
| パッケージ | 20-lead (18-pin) QFN with exposed pad, 4 mm x 3 mm |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Lead-Free / PBF | Yes (PBF suffix) |
LT8640IUDC-1 ピン構成
| ピン 1 | VIN — Input supply voltage, 3.4V to 42V |
| ピン 2 | VIN — Input supply voltage (second pin) |
| ピン 3 | BST — Boost flying capacitor for high-side gate drive |
| ピン 4 | SW — Switch node - connection to inductor |
| ピン 5 | SW — Switch node (second pin) |
| ピン 6 | PGND — Power ground |
| ピン 7 | PGND — Power ground (second pin) |
| ピン 8 | PGND — Power ground (third pin) |
| ピン 9 | PGND — Power ground (fourth pin) |
| ピン 10 | RT — Timing resistor to program switching frequency |
| ピン 11 | SYNC/MODE — Mode pin: Burst/spread-spectrum/SYNC/forced CCM |
| ピン 12 | SS — Soft-start programming |
| ピン 13 | TR/SS — Tracking / soft-start input |
| ピン 14 | FB — Voltage feedback from output divider |
| ピン 15 | VOUT — Output voltage sense (internal bias) |
| ピン 16 | EN/UV — Enable / undervoltage lockout |
| ピン 17 | INTVCC — Internal 3.4V LDO bypass |
| ピン 18 | BIAS — Optional bias supply for higher efficiency |
| ピン 19 | NC — Not connected (per datasheet) |
| ピン 20 | EP — Exposed pad - thermal and PGND, must be soldered to PCB |
主な用途
LT8640IUDC-1 の用途: 6 件s: 24V Industrial Sensor and Actuator Power Rails, Automotive Infotainment and Body Electronics, Battery-Powered Portable and IoT Devices, Point-of-Load Supply After 24V/12V Bus, Test and Measurement Instrumentation, Surveillance and Security Camera Power.
24V Industrial Sensor and Actuator Power Rails
The LT8640IUDC-1 is ideally suited to 24V industrial sensor rails because its 42V input tolerance easily absorbs 24V bus transients, and its 5A continuous current supports multi-sensor loads including 4-20mA loops, PLCs, and motor pre-drivers. Silent Switcher architecture meets CISPR 22 EMI limits without shielding, simplifying EN 61131-2 compliance for industrial control cabinets. The 2.5µA quiescent current enables always-on standby operation with battery-backed industrial controllers, while the 200kHz-3MHz switching range allows small inductors and a compact 4mm x 3mm footprint suitable for dense PLC backplanes.
おすすめ
Automotive Infotainment and Body Electronics
The LT8640IUDC-1 powers infotainment head units, instrument clusters, and body controllers from 12V automotive rails. Its 42V input margin covers ISO 7637-2 load-dump transients without external TVS, reducing BOM cost. Silent Switcher EMI performance eliminates the need for an EMI shield, allowing placement near RF-sensitive antenna and tuner sections. For AEC-Q100 qualified automotive designs the LT8640EUDC-1#TRPBF variant is a drop-in alternative, providing the same QFN-20 (UDC) footprint while adding automotive PPAP documentation. The 5A output current supports multiple downstream rails via secondary LDOs.
おすすめ
Battery-Powered Portable and IoT Devices
The LT8640IUDC-1's 2.5µA quiescent current is the headline feature for battery-powered IoT and portable designs. With the output in full regulation at no load, a Li-ion or 4xAA battery stack can stay in standby for years without draining. The wide VIN range supports direct connection to multi-cell battery chemistries (Li-ion, lead-acid, 4x NiMH) without pre-regulation. Silent Switcher architecture prevents switching noise from coupling into adjacent analog or RF circuits, critical for BLE/Wi-Fi IoT modules where conducted noise degrades radio sensitivity. The 4mm x 3mm QFN-20 package fits wearable and sensor-hub form factors.
おすすめ
Point-of-Load Supply After 24V/12V Bus
The LT8640IUDC-1 is a workhorse point-of-load converter for distributed power architectures where 24V or 12V intermediate buses feed multiple POL regulators downstream. With 5A output and 96%+ peak efficiency at 12V to 5V conversion, the LT8640IUDC-1 minimizes thermal stress on dense PCBs. The 30ns minimum on-time enables high-frequency 3MHz operation at large VIN-VOUT deltas, shrinking inductor size. Forced continuous mode (the -1 variant) avoids discontinuous-conduction-mode audio noise that would otherwise couple into adjacent analog POLs through ground bounce.
おすすめ
Test and Measurement Instrumentation
In bench-top oscilloscopes, signal generators, and lab power supplies, the LT8640IUDC-1 provides clean, low-ripple power rails for sensitive analog front-ends including ADC reference ladders, DAC output stages, and op-amp supply pins. The Silent Switcher 3MHz switching capability can be synchronized to an external clock placed above the AM band, eliminating beat-frequency interference with sensitive measurements. Forced continuous mode maintains constant switching frequency across load steps, reducing transient response variation that would otherwise show up as supply-noise artifacts on the measured signal.
おすすめ
Surveillance and Security Camera Power
PoE-powered and 12V/24V security cameras benefit from the LT8640IUDC-1's Silent Switcher architecture because the switching noise does not couple into the camera's image sensor or analog video chain, preserving low-light image quality. The wide VIN range accepts PoE-extracted 12V or 24V directly without pre-regulation. The 5A output current supports a single converter feeding multiple camera subsystems - image sensor, IR illuminator, heater, and network interface. The forced continuous mode (LT8640-1) prevents DCM-induced audio-frequency noise that can couple into microphone channels used in audio-equipped surveillance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LT8640IUDC-1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LT8640IUDC#PBF | LT8640IUDC-1#TRPBF | LT8640EUDC#TRPBF | LT8640EUDC-1#TRPBF | LT8641HUDC#PBF |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-lead QFN with exposed pad, 4 mm x 3 mm | 20-lead QFN with exposed pad, 4 mm x 3 mm - same | 20-lead QFN with exposed pad, 4 mm x 3 mm - same | 20-lead QFN with exposed pad, 4 mm x 3 mm - same | 20-lead QFN with exposed pad, 4 mm x 3 mm - same | 20-lead QFN with exposed pad, 4 mm x 3 mm - same |
| Input Voltage Range | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 42 V | 3.4 V to 65 V |
| Maximum Output Current | 5 A | 5 A | 5 A | 5 A | 5 A | 3.5 A |
| Quiescent Current | 2.5 µA | 2.5 µA | 2.5 µA | 2.5 µA | 2.5 µA | 2.5 µA |
| Temperature Grade | I grade: -40C to +125C | I grade | I grade | E grade: 0C to +125C | E grade | H grade |
| Switching Frequency Range | 200 kHz to 3 MHz | 200 kHz to 3 MHz | 200 kHz to 3 MHz | 200 kHz to 3 MHz | 200 kHz to 3 MHz | 200 kHz to 3 MHz |
主な差別化要因
- Highest efficiency at very light loads with 2.5µA quiescent current （vs LT8606EDC#TRPBF (typical alternative buck converters))
- Wide VIN range with high load-current capability in compact package （vs LT8641HUDC#PBF)
- Forced continuous mode at light loads (LT8640-1 variant) （vs LT8640IUDC#PBF (standard pulse-skipping version))
設計ノート
Silent Switcher architecture relies on tightly-coupled VIN-PGND and SW-PGND capacitor loops. Place the input ceramic capacitor (minimum 10µF X7R) immediately adjacent to the VIN and PGND pads, with the shortest possible trace to minimize the high-dV/dt loop area. Without this layout discipline, Silent Switcher loses its EMI advantage. The exposed pad must be soldered to a continuous PGND copper pour of at least 1 square inch for thermal dissipation; via stitching to internal PGND planes is recommended.
Estimated: at 12V VIN to 5V VOUT at 5A load, the LT8640IUDC-1 dissipates approximately (12V-5V)*5A*1/eta watts; assuming 90% efficiency, that is ~3.9W. With a 4mm x 3mm QFN-20 and the exposed pad soldered to 1 square inch of 1oz copper, theta_JA is approximately 38 C/W, giving a junction temperature rise of 148 C above ambient - too high for 85 C ambient operation. For continuous 5A output at 12V-to-5V conversion, increase the copper pour to 2-3 square inches or upgrade to the LT8650-series with better thermal performance.
Do not use output capacitors smaller than 10µF total - the LT8640 control loop requires a minimum output capacitance for stability, and using smaller values can cause oscillation or poor load-step response. Use low-ESR ceramic capacitors (X7R dielectric). Avoid placing the RT resistor close to noisy traces, as frequency-programming noise can couple in. The SYNC/MODE pin must be tied to a known logic state - leaving it floating may cause unexpected mode transitions. For high-dV/dt applications, ensure the BIAS pin is tied to a stable 3.3V or 5V rail to maximize efficiency.
The Silent Switcher architecture typically meets CISPR 22 Class B radiated and conducted EMI without a shield, but only with proper PCB layout. If the design fails EMI, common causes are: (1) input capacitor placed too far from VIN/PGND pads, (2) insufficient copper area on the exposed pad, (3) output inductor chosen with low SRF (self-resonant frequency below 100 MHz), (4) SYNC/MODE not configured for spread-spectrum mode. Use spread-spectrum mode (SYNC/MODE tied to ground through a specific resistor network) to further reduce peak EMI by ~10dB.
コンプライアンス情報
RoHS compliant per PBF suffix on DigiKey/Mouser listings. The LT8640IUDC-1 itself is industrial-grade (I temp range) - choose the LT8640EUDC-1#TRPBF AEC-Q100 automotive variant for AEC-Q100 qualified designs.
