MAX202EWE+T - 120kbps RS-232 Transceiver | Analog Devices
部品番号: MAX202EWE+T ✓ 生産中MAX202EWE+T 概要
An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a cable-based RS-232 port. Within the interface-IC hierarchy, it sits between general digital logic and differential or bipolar communication circuitry. The MAX202EWE+T integrates both signal conversion and charge-pump support, reducing the number of external components required for a working bidirectional RS-232 port.
The device provides two transmit channels and two receive channels. Its integrated charge-pump circuitry supports the positive and negative voltage levels required by RS-232 from one 5 V supply. According to the Analog Devices MAX202E datasheet, the drivers maintain ±5 V EIA/TIA-232E output levels at data rates in excess of 120 kbps when loaded according to the applicable interface requirements.
The E-series interface is intended for designs where reliable operation in the presence of noisy environments or partially powered systems is important. The MAX202E family also provides receiver behavior that helps control bus contention when the interface may be exposed to an active external driver. Exact input thresholds, receiver hysteresis, and protection details should be confirmed in the manufacturer datasheet before finalizing an industrial safety design.
Typical uses include RS-232 service ports on test and measurement equipment, industrial controllers, point-of-sale terminals, instrumentation, and computer peripherals. Two channels allow one connector to carry two data paths, while receive channels can monitor status, handshake, or equipment-control signals when the host uses hardware handshaking.
PCB design should preserve the datasheet’s external-capacitor and charge-pump layout, provide a continuous return path between the interface and connector ground, and keep the RS-232 driver outputs away from sensitive analog circuitry. Decoupling capacitance and placement requirements should be implemented exactly as shown in the manufacturer’s recommended layout to maintain stable operation.
This product data combines the manufacturer’s interface specifications, verified distributor listings, package information, replacement analysis, and practical PCB guidance. It is intended to accelerate component selection and board-level implementation without obscuring the electrical limits of the MAX202EWE+T.
ドロップイン代替品: MAX202EWE+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX202EWE+T (同一形状・フットプリント) — 相違点: Product Type, Interface Standard, Mounting Type, Package, ESD Protection.
MAX202CWE+T
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MAX232EWE+T
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX232CWE+T
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX202EWE+T 仕様
| Product Type | RS-232 transceiver |
| Transmitter Channels | 2 channels |
| Receiver Channels | 2 channels |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | +5 V |
| Maximum Data Rate | 120 kbps |
| Driver Output Level | ±5 V EIA/TIA-232E |
| External Charge-Pump Capacitor | 0.1 µF |
| パッケージ | 16-pin wide SOIC |
| ピン数 | 16 pins |
| 実装タイプ | Surface mount |
MAX202EWE+T 16-pin wide soic ピン配置ガイド
MAX202EWE+T (16-pin wide soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX202EWE+T.
詳細は データシート をご参照ください。
主な用途
MAX202EWE+T の用途: 6 件s: Industrial Controller Serial Port, Test and Measurement Equipment, Point-of-Sale Terminal, Instrumentation Data Link, Computer Peripheral Connectivity, Network Equipment Maintenance Port.
Industrial Controller Serial Port
The MAX202EWE+T is appropriate for an industrial controller that must communicate with a service console or peripheral through an RS-232 port. Its 4.5 V to 5.5 V single-supply operation fits a regulated 5 V control rail, while the 2-driver and 2-receiver arrangement can support one data channel plus handshake or status signaling. Operation up to 120 kbps permits faster diagnostic traffic than a conventional slow modem port. The 16-pin wide SOIC keeps the interface compact, but the 0.1 µF charge-pump capacitors must follow the Analog Devices application circuit and layout to maintain reliable startup and output levels.
おすすめ
Test and Measurement Equipment
The MAX202EWE+T can connect a measurement instrument or laboratory controller to an RS-232 host while keeping the interface powered from a single 5 V rail. Its 120 kbps capability is suitable for command transfer, status reporting, and automated test sequences, and the two receive channels can monitor control or handshake lines. The integrated charge-pump circuit eliminates a separate negative supply, while four external 0.1 µF capacitors provide the required voltage multiplication. Place those capacitors close to the specified pins, maintain a low-impedance ground return, and separate the RS-232 output routing from sensitive measurement circuitry to reduce coupling.
おすすめ
Point-of-Sale Terminal
A point-of-sale terminal can use the MAX202EWE+T to bridge a low-power host controller to a legacy RS-232 peripheral such as a printer, scanner, or customer display. The single 5 V supply fits compact embedded systems, and data rates up to 120 kbps are more than adequate for short transaction-oriented command exchanges. Two transmitters and two receivers provide flexibility for data, control, and status signals. The principal design concern is ground noise: keep the connector-side return tied to the interface ground through the layout recommended by Analog Devices, use suitable protection at exposed connectors, and route driver outputs away from display and power-conversion circuitry.
おすすめ
Instrumentation Data Link
The MAX202EWE+T is well suited to short-distance instrumentation links where both ends use RS-232 and a +5 V interface supply is preferred. Its 120 kbps maximum supports bursty measurement data, configuration commands, and diagnostic reports without requiring a separate negative rail. The E-series receiver implementation can also help manage communication when the port may experience noise or partial-power conditions, subject to the system-level grounding and protection design. The wide SOIC package offers adequate routing space for the charge-pump network, but the four 0.1 µF capacitors still require placement consistent with the manufacturer’s reference layout.
おすすめ
Computer Peripheral Connectivity
The MAX202EWE+T can provide a legacy RS-232 connection from a modern embedded controller to a computer peripheral or service interface. Because the host logic operates at low voltage, the transceiver handles both signal translation and the bipolar voltage conversion required at the cable side. Supporting data rates up to 120 kbps allows rapid command exchange and firmware-style control traffic. Designers should use a quality cable with a defined ground conductor, minimize the distance through which the driver output remains exposed, and add appropriate connector protection if the equipment is exposed to user-accessible cabling. The external capacitors and charge-pump routing must match the datasheet layout.
おすすめ
Network Equipment Maintenance Port
The MAX202EWE+T is useful for an equipment maintenance port that must remain accessible through a conventional RS-232 connection while the main system operates from a 5 V rail. A service laptop can exchange configuration data, firmware logs, and diagnostic commands at rates up to 120 kbps. The two available channels can carry one main data path and one auxiliary handshake path, improving compatibility with older equipment. Because maintenance connectors are often exposed to electrostatic discharge and ground-potential differences, the final design should combine the interface layout in the MAX202E datasheet with suitable board-level surge and ESD protection rather than relying on the IC alone.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX202EWE+T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX202CWE+T | MAX232EWE+T | MAX232CWE+T |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC |
| Product Type | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps | 120 kbps |
| External Charge-Pump Capacitor | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF |
| Number of Drivers | 2 channels | 2 channels | 2 channels | 2 channels |
| Number of Receivers | 2 channels | 2 channels | 2 channels | 2 channels |
主な差別化要因
- Single-supply RS-232 operation simplifies system power design (vs MAX232EWE+T)
- Five-volt rail compatibility with a slightly wider listed supply ceiling (vs MAX202CWE+T)
- Same 120 kbps interface-performance class with explicit EIA/TIA-232E positioning (vs MAX232CWE+T)
設計ノート
Implement the four 0.1 µF charge-pump capacitors using the values and topology shown in the Analog Devices MAX202E datasheet. Place each capacitor close to its associated device pin, minimize loop area between capacitor and package, and avoid routing the charge-pump nets beneath long signal paths. Incorrect capacitor values or lengthy traces can disturb startup and degrade the bipolar driver levels, even when the nominal supply and logic connections are correct.
Keep the RS-232 driver traces short and isolate them from sensitive analog or high-speed digital paths. Route the interface ground as a continuous return conductor, preferably following the cable ground toward the connector rather than relying on a fragmented plane connection. This reduces common-impedance disturbance and helps limit charging current injected into the system ground when driver outputs change between positive and negative signal levels.
Do not treat the 16-pin SOIC footprint alone as proof that a MAX202-family substitute is interchangeable. Verify supply limits, operating-temperature range, receiver thresholds, fail-safe behavior, external-capacitor requirements, and ESD performance in each manufacturer datasheet. For example, MAX202CWE+T has a listed 5.25 V maximum supply compared with 5.5 V for MAX202EWE+T, so a regulated 5 V rail remains important even when nominal operation appears equivalent.
コンプライアンス情報
The MAX202E family is identified as meeting EIA/TIA-232E and CCITT V.28 interface requirements, but product-specific environmental and material-compliance status requires confirmation from the manufacturer.