Analog Devices

MAX202EWE+T - 120kbps RS-232 Transceiver | Analog Devices

부품 번호: MAX202EWE+T ✓ 활성
4.5 V to 5.5 V Vdss 16-pin wide SOIC Package
MOQ: 1 |

MAX202EWE+T 개요

The Analog Devices MAX202EWE+T is a single-supply RS-232 line-interface transceiver with two drivers and two receivers, data rates up to 120 kbps, and a 16-pin wide SOIC package. Its nominal +5 V supply, 4.5 V to 5.5 V operating range, and external 0.1 µF charge-pump capacitors make it suitable for compact serial interfaces, industrial equipment, and legacy computer communication ports.

An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a cable-based RS-232 port. Within the interface-IC hierarchy, it sits between general digital logic and differential or bipolar communication circuitry. The MAX202EWE+T integrates both signal conversion and charge-pump support, reducing the number of external components required for a working bidirectional RS-232 port.

The device provides two transmit channels and two receive channels. Its integrated charge-pump circuitry supports the positive and negative voltage levels required by RS-232 from one 5 V supply. According to the Analog Devices MAX202E datasheet, the drivers maintain ±5 V EIA/TIA-232E output levels at data rates in excess of 120 kbps when loaded according to the applicable interface requirements.

The E-series interface is intended for designs where reliable operation in the presence of noisy environments or partially powered systems is important. The MAX202E family also provides receiver behavior that helps control bus contention when the interface may be exposed to an active external driver. Exact input thresholds, receiver hysteresis, and protection details should be confirmed in the manufacturer datasheet before finalizing an industrial safety design.

Typical uses include RS-232 service ports on test and measurement equipment, industrial controllers, point-of-sale terminals, instrumentation, and computer peripherals. Two channels allow one connector to carry two data paths, while receive channels can monitor status, handshake, or equipment-control signals when the host uses hardware handshaking.

PCB design should preserve the datasheet’s external-capacitor and charge-pump layout, provide a continuous return path between the interface and connector ground, and keep the RS-232 driver outputs away from sensitive analog circuitry. Decoupling capacitance and placement requirements should be implemented exactly as shown in the manufacturer’s recommended layout to maintain stable operation.

This product data combines the manufacturer’s interface specifications, verified distributor listings, package information, replacement analysis, and practical PCB guidance. It is intended to accelerate component selection and board-level implementation without obscuring the electrical limits of the MAX202EWE+T.

드롭인 대체품: MAX202EWE+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: MAX202EWE+T (동일 폼 팩터 및 풋프린트) — 차이점: Product Type, Interface Standard, Mounting Type, Package, ESD Protection.

Analog Devices
ESD Protection: ±15 kV human body model
비교 대상: MAX202EWE+T →
Maxim Integrated
Interface Standard: EIA/TIA-232E and CCITT V.28
Mounting Type: Surface-mount SMD
ESD Protection: ±15 kV HBM
비교 대상: MAX202EWE+T →
Analog Devices
Product Type: RS-232 line-driver and receiver transceiver
Interface Standard: EIA/TIA-232E, V.28, and V.24
Package: 16-pin wide SOIC (WSOIC)
비교 대상: MAX202EWE+T →
Maxim Integrated
Product Type: RS-232 transceiver interface IC
Interface Standard: EIA/TIA-232E
비교 대상: MAX202EWE+T →

MAX202CWE+T

✅ 드롭인 ⚠️ 사양 미검증
📦 16-pin wide SOIC
Maximum supply voltage is 5.25 V versus 5.5 V, a 4.5% reduction; data rate remains 120 kbps

📋 참조 대체품 (카탈로그에 없음)

MAX232EWE+T

✅ 드롭인 ⚠️ 사양 미검증
Maxim Integrated
📦 16-pin wide SOIC
RS-232 transceiver interface IC · 2 drivers · 2 receivers · 4.5 V to 5.5 V · 120 kbps · EIA/TIA-232E · CCITT V.28 and V.24 · +5 V

가격 문의

데이터시트 보기 →

MAX232CWE+T

✅ 드롭인 ⚠️ 사양 미검증
Analog Devices
📦 16-pin wide SOIC
RS-232 line-driver and receiver transceiver · 2 · 2 · Full duplex · 120 kbps · +5 V · EIA/TIA-232E, V.28, and V.24 · 16-pin wide SOIC (WSOIC)

가격 문의

데이터시트 보기 →

MAX202EWE+T 사양

Product Type RS-232 transceiver
Transmitter Channels 2 channels
Receiver Channels 2 channels
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage +5 V
Maximum Data Rate 120 kbps
Driver Output Level ±5 V EIA/TIA-232E
External Charge-Pump Capacitor 0.1 µF
패키지 16-pin wide SOIC
핀 수 16 pins
실장 유형 Surface mount

MAX202EWE+T 16-pin wide soic 핀 구성 가이드

MAX202EWE+T(16-pin wide soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

MAX202EWE+T의 16-pin wide soic 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: MAX202EWE+T.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

MAX202EWE+T 적합 용도: 6 애플리케이션s: Industrial Controller Serial Port, Test and Measurement Equipment, Point-of-Sale Terminal, Instrumentation Data Link, Computer Peripheral Connectivity, Network Equipment Maintenance Port.

🏭

Industrial Controller Serial Port

The MAX202EWE+T is appropriate for an industrial controller that must communicate with a service console or peripheral through an RS-232 port. Its 4.5 V to 5.5 V single-supply operation fits a regulated 5 V control rail, while the 2-driver and 2-receiver arrangement can support one data channel plus handshake or status signaling. Operation up to 120 kbps permits faster diagnostic traffic than a conventional slow modem port. The 16-pin wide SOIC keeps the interface compact, but the 0.1 µF charge-pump capacitors must follow the Analog Devices application circuit and layout to maintain reliable startup and output levels.

🖥️

Test and Measurement Equipment

The MAX202EWE+T can connect a measurement instrument or laboratory controller to an RS-232 host while keeping the interface powered from a single 5 V rail. Its 120 kbps capability is suitable for command transfer, status reporting, and automated test sequences, and the two receive channels can monitor control or handshake lines. The integrated charge-pump circuit eliminates a separate negative supply, while four external 0.1 µF capacitors provide the required voltage multiplication. Place those capacitors close to the specified pins, maintain a low-impedance ground return, and separate the RS-232 output routing from sensitive measurement circuitry to reduce coupling.

📺

Point-of-Sale Terminal

A point-of-sale terminal can use the MAX202EWE+T to bridge a low-power host controller to a legacy RS-232 peripheral such as a printer, scanner, or customer display. The single 5 V supply fits compact embedded systems, and data rates up to 120 kbps are more than adequate for short transaction-oriented command exchanges. Two transmitters and two receivers provide flexibility for data, control, and status signals. The principal design concern is ground noise: keep the connector-side return tied to the interface ground through the layout recommended by Analog Devices, use suitable protection at exposed connectors, and route driver outputs away from display and power-conversion circuitry.

🔧

Instrumentation Data Link

The MAX202EWE+T is well suited to short-distance instrumentation links where both ends use RS-232 and a +5 V interface supply is preferred. Its 120 kbps maximum supports bursty measurement data, configuration commands, and diagnostic reports without requiring a separate negative rail. The E-series receiver implementation can also help manage communication when the port may experience noise or partial-power conditions, subject to the system-level grounding and protection design. The wide SOIC package offers adequate routing space for the charge-pump network, but the four 0.1 µF capacitors still require placement consistent with the manufacturer’s reference layout.

💻

Computer Peripheral Connectivity

The MAX202EWE+T can provide a legacy RS-232 connection from a modern embedded controller to a computer peripheral or service interface. Because the host logic operates at low voltage, the transceiver handles both signal translation and the bipolar voltage conversion required at the cable side. Supporting data rates up to 120 kbps allows rapid command exchange and firmware-style control traffic. Designers should use a quality cable with a defined ground conductor, minimize the distance through which the driver output remains exposed, and add appropriate connector protection if the equipment is exposed to user-accessible cabling. The external capacitors and charge-pump routing must match the datasheet layout.

🌐

Network Equipment Maintenance Port

The MAX202EWE+T is useful for an equipment maintenance port that must remain accessible through a conventional RS-232 connection while the main system operates from a 5 V rail. A service laptop can exchange configuration data, firmware logs, and diagnostic commands at rates up to 120 kbps. The two available channels can carry one main data path and one auxiliary handshake path, improving compatibility with older equipment. Because maintenance connectors are often exposed to electrostatic discharge and ground-potential differences, the final design should combine the interface layout in the MAX202E datasheet with suitable board-level surge and ESD protection rather than relying on the IC alone.

What are the key specifications of MAX202EWE+T that engineers should know?
The MAX202EWE+T is a 2-driver, 2-receiver RS-232 transceiver for a 4.5 V to 5.5 V supply, with operation up to 120 kbps in a 16-pin wide SOIC package. According to the Analog Devices MAX202E datasheet, it produces ±5 V EIA/TIA-232E driver levels and requires 0.1 µF external charge-pump capacitors. The device is suitable for systems that need a compact, single-supply interface between low-voltage digital logic and a cable-based RS-232 port.
Where to download the MAX202EWE+T datasheet PDF?
The authoritative MAX202EWE+T documentation is available through Analog Devices’ MAX202E product page at https://www.analog.com/en/products/max202e.html. The manufacturer product page identifies the MAX202E family as compliant with EIA/TIA-232E and CCITT V.28 requirements at data rates up to 120 kbps. Use the datasheet linked from that page for the complete pin description, electrical characteristics, recommended application circuit, and PCB layout.
Where can I find the MAX202EWE+T pinout?
The MAX202EWE+T uses a 16-pin wide SOIC package, and its complete pin assignment is published in the Analog Devices MAX202E datasheet. Use the pin-description table and package drawing on the official product page rather than assigning connections from a distributor summary. The external charge-pump capacitor connections, driver outputs, receiver inputs, supply pins, and ground pins must be checked directly against the manufacturer diagram before PCB release.
What is the operating voltage range of MAX202EWE+T?
The MAX202EWE+T operates from a single 4.5 V to 5.5 V supply, with +5 V as its nominal operating condition. The Analog Devices MAX202E datasheet describes the integrated charge-pump circuitry that develops the bipolar voltage levels required by an RS-232 interface. Designers should therefore design the board for a regulated 5 V rail and verify regulator tolerance, startup behavior, and decoupling against the datasheet guidance.
How fast can MAX202EWE+T transmit RS-232 data?
The MAX202EWE+T supports data rates up to 120 kbps when operated according to the EIA/TIA-232E loading requirements. The Analog Devices MAX202E product page also states that the drivers maintain ±5 V EIA/TIA-232E output levels at rates in excess of 120 kbps when properly loaded. Cable length, capacitance, slew rate, grounding, and the selected protocol still determine whether the complete communication link operates reliably at the maximum rate.
Where to buy MAX202EWE+T online?
Use the Request a Quote form on this page to request MAX202EWE+T availability, lead time, and a current quotation. The form allows the exact +T tape-and-reel ordering suffix to be included in the request, avoiding ambiguity with other package or temperature markings. A complete request should state the required quantity, production schedule, and whether the shipment must include a reel, tray, or another approved packing format.
What is the price of MAX202EWE+T?
The current MAX202EWE+T quotation is generated through the Request a Quote form on this page rather than published as a static price. Submit the exact MPN, required reel quantity, and expected shipment timing with the request. This approach ensures that the quote reflects the MAX202EWE+T suffix, market availability, and requested quantity at the time of order rather than an outdated catalog figure.
What is the lead time for MAX202EWE+T?
The current lead time for MAX202EWE+T is available through the Request a Quote form on this page. Include your required quantity, production date, and approved packing method when submitting the request. Because supply conditions can change by quantity and schedule, engineers should obtain written confirmation before committing a build schedule around the MAX202EWE+T.
Is MAX202EWE+T in stock?
Use the Request a Quote form on this page to check current MAX202EWE+T stock and expected fulfillment timing. The request should identify the exact tape-and-reel ordering suffix, quantity, and target delivery date. A stock confirmation should be obtained for the quantity needed rather than assuming that a distributor catalog page reflects immediately available material.
What can replace MAX202EWE+T?
A valid drop-in replacement must use the same 16-pin wide SOIC footprint, support the same 4.5 V to 5.5 V supply, and remain within the target’s 120 kbps RS-232 performance class. MAX202CWE+T, MAX232EWE+T, and MAX232CWE+T are same-manufacturer candidates for review, but their temperature, protection, and exact electrical details should be compared with the MAX202EWE+T datasheet. The Request a Quote form can confirm availability of the selected replacement.
Can MAX202CWE+T replace MAX202EWE+T?
The MAX202CWE+T is a strong footprint candidate because it is also identified as a 16-pin wide SOIC MAX202-family RS-232 transceiver, but it is not automatically interchangeable in every application. The listed comparison data identifies a maximum supply difference of 5.25 V for MAX202CWE+T versus 5.5 V for MAX202EWE+T. Confirm operating-temperature limits, receiver behavior, ESD protection, and charge-pump capacitor values in the manufacturer datasheets before approving the substitution.
What is the difference between MAX202EWE+T and MAX232EWE+T?
Both devices are identified as 16-pin RS-232 transceivers in the same wide-SOIC family format, and both are associated with a maximum data rate of 120 kbps. Their functional roles overlap, but receiver fail-safe behavior and detailed electrical limits must be checked independently in the manufacturer datasheets. Select MAX202EWE+T when its E-series interface requirements match the design; otherwise use the MAX232EWE+T data sheet as the controlling document.
When should I choose MAX202EWE+T over MAX202CWE+T?
Choose the MAX202EWE+T when the system requires the specific E-series MAX202 interface and its documented operating limits. The MAX202CWE+T may be considered when its lower listed maximum supply voltage, temperature range, and protection characteristics satisfy the application. Because a common package is necessary but not sufficient for replacement approval, compare enable behavior, supply limits, receiver thresholds, ESD ratings, and external-capacitor requirements before selecting between them.
Is MAX202EWE+T suitable for industrial RS-232 equipment?
The MAX202EWE+T can be used in industrial RS-232 equipment when the operating temperature, protection level, grounding, and cable environment meet the device’s published limits. Its single 5 V supply and 120 kbps capability suit controller-to-instrument links, while the E-series designation identifies the relevant Maxim interface family. The MAX202E datasheet and the final system’s isolation and surge requirements should determine qualification for the specific industrial environment.
Does MAX202EWE+T require external charge-pump capacitors?
The MAX202EWE+T requires four external 0.1 µF capacitors for its charge-pump circuitry. The Analog Devices MAX202E product information identifies the MAX202E as a +5 V RS-232 transceiver with 0.1 µF external capacitors. Follow the manufacturer’s recommended circuit and layout values exactly because incorrect capacitance, excessive trace resistance, or poor placement can impair startup and output-level performance.

엔지니어링 참조 데이터: MAX202EWE+T — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the MAX202EWE+T when a design requires a two-channel, two-channel RS-232 interface powered from a single 5 V rail, operation up to 120 kbps, and a 16-pin wide SOIC footprint. Its E-series interface and ±5 V EIA/TIA-232E driver levels suit legacy equipment, service ports, and instrumentation. Consider MAX202CWE+T when its lower 5.25 V maximum supply and separately documented temperature limits are acceptable, but verify every replacement-critical characteristic. MAX232EWE+T and MAX232CWE+T offer comparable package-format and data-rate classes, yet receiver behavior, fail-safe characteristics, protection, and operating-temperature limits must be checked before approval. None of these choices eliminates the need to follow the manufacturer’s charge-pump capacitor and layout requirements.

대체품과의 비교

파라미터 이 제품 MAX202CWE+T MAX232EWE+T MAX232CWE+T
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-pin wide SOIC 16-pin wide SOIC 16-pin wide SOIC 16-pin wide SOIC
Product Type 2/2 RS-232 transceiver 2/2 RS-232 transceiver 2/2 RS-232 transceiver 2/2 RS-232 transceiver
Maximum Data Rate 120 kbps 120 kbps 120 kbps 120 kbps
External Charge-Pump Capacitor 0.1 µF 0.1 µF 0.1 µF 0.1 µF
Number of Drivers 2 channels 2 channels 2 channels 2 channels
Number of Receivers 2 channels 2 channels 2 channels 2 channels

주요 차별점

  • Single-supply RS-232 operation simplifies system power design (vs MAX232EWE+T)
  • Five-volt rail compatibility with a slightly wider listed supply ceiling (vs MAX202CWE+T)
  • Same 120 kbps interface-performance class with explicit EIA/TIA-232E positioning (vs MAX232CWE+T)

설계 노트

Implement the four 0.1 µF charge-pump capacitors using the values and topology shown in the Analog Devices MAX202E datasheet. Place each capacitor close to its associated device pin, minimize loop area between capacitor and package, and avoid routing the charge-pump nets beneath long signal paths. Incorrect capacitor values or lengthy traces can disturb startup and degrade the bipolar driver levels, even when the nominal supply and logic connections are correct.

Keep the RS-232 driver traces short and isolate them from sensitive analog or high-speed digital paths. Route the interface ground as a continuous return conductor, preferably following the cable ground toward the connector rather than relying on a fragmented plane connection. This reduces common-impedance disturbance and helps limit charging current injected into the system ground when driver outputs change between positive and negative signal levels.

Do not treat the 16-pin SOIC footprint alone as proof that a MAX202-family substitute is interchangeable. Verify supply limits, operating-temperature range, receiver thresholds, fail-safe behavior, external-capacitor requirements, and ESD performance in each manufacturer datasheet. For example, MAX202CWE+T has a listed 5.25 V maximum supply compared with 5.5 V for MAX202EWE+T, so a regulated 5 V rail remains important even when nominal operation appears equivalent.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The MAX202E family is identified as meeting EIA/TIA-232E and CCITT V.28 interface requirements, but product-specific environmental and material-compliance status requires confirmation from the manufacturer.

데이터 검증일: 2026-11-13 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

MAX202EWE+T datasheet MAX202EWE+T pinout MAX202EWE+T datasheet pdf MAX202EWE+T equivalent MAX202EWE+T replacement MAX202EWE+T cross reference MAX202EWE+T vs MAX202CWE+T MAX202EWE+T vs MAX232EWE+T MAX202EWE+T 120kbps MAX202EWE+T 16-SOIC Analog Devices MAX202EWE+T MAX202EWE+T industrial RS-232 MAX202EWE+T price MAX202EWE+T stock

관련 부품 & 용어

Analog Devices MAX202EWE+T MAX202CWE+T MAX232EWE+T MAX232CWE+T RS-232 transceiver RS-232 interface line-interface IC interface IC semiconductor EIA/TIA-232E CCITT V.28 SOIC-16 wide SOIC surface mount SMD package charge-pump capacitor single 5 V supply 120 kbps data rate RS-232 driver RS-232 receiver industrial equipment test and measurement equipment partial-power receiver operation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기