MAX232DWRG4 - Dual 120kbps RS-232 | Texas Instruments
部品番号: MAX232DWRG4 ✓ 生産中MAX232DWRG4 概要
An RS-232 transceiver is an interface IC that translates low-voltage digital logic levels into the positive and negative voltage levels used by RS-232 equipment. Within the interface hierarchy, it belongs to the line-driver and line-receiver family, provides physical-layer signal conditioning, and bridges a host controller or UART with an external data port.
Key features include a single 5 V supply, operation up to 120 kbps, ±9 V driver output levels, and ±2 kV ESD protection. The integrated dual-driver and dual-receiver configuration supports two communication channels in one package. Its commercial-grade operating range is 0°C to 70°C, making it appropriate for room-temperature industrial, instrumentation, and embedded-control systems.
The MAX232DWRG4 uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 from one 5 V supply. Its receiver converts incoming EIA-232-F signals into TTL/CMOS-compatible levels, while its driver converts outgoing logic levels into RS-232 signals. The interface conforms to EIA-232-F, TIA-232-F, and V.28 requirements identified for this device.
Typical uses include industrial control panels, serial test equipment, data acquisition systems, point-of-sale terminals, and embedded RS-232 ports. Its 120 kbps capability is suitable for moderate-speed point-to-point links, although modern high-speed or long-distance designs may require a more suitable RS-232 transceiver family.
PCB implementation should follow the manufacturer pin-description and capacitor-connection diagrams. Place charge-pump capacitors close to their specified pins, keep RS-232 routing away from sensitive analog and high-speed clock traces, and provide suitable logic-side ground return paths. The external RS-232 connector may also require additional transient-protection measures for exposed cables.
This page combines the manufacturer’s principal electrical ratings with package details, interface standards, replacement guidance, and practical layout considerations. It is intended to help engineers evaluate the MAX232DWRG4 for 5 V RS-232 designs and identify compatible second-source options without changing the 16-pin SOIC footprint.
ドロップイン代替品: MAX232DWRG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX232DWRG4 (同一形状・フットプリント) — 相違点: Maximum Data Rate, Product Type.
MAX232DWR
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX232DWE4
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX232CWE4
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MAX232AWE4
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
ST232BDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX232DWRG4 仕様
| Product Type | Dual RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| 電源電圧 | 5 V |
| Maximum Data Rate | 120 kbps |
| Driver Output Level | ±9 V |
| ESD Protection | ±2 kV |
| Interface Standards | EIA-232-F, TIA-232-F, V.28 |
| パッケージ | 16-pin SOIC |
| Terminal Count | 16 |
| Temperature Grade | Commercial |
| 動作温度 | 0°C to 70°C |
| Peak Reflow Temperature | 260°C |
| 実装タイプ | Surface mount |
| Lead Form | Gull wing |
| Package Code | SOP |
| Package Shape | Rectangular |
MAX232DWRG4 ピン構成
| ピン 1 | R1OUT — Receiver 1 output |
| ピン 2 | R2OUT — Receiver 2 output |
| ピン 3 | R2IN — Receiver 2 input |
| ピン 4 | R1IN — Receiver 1 input |
| ピン 5 | GND — Ground |
| ピン 6 | V+ — Positive supply voltage |
| ピン 7 | R1IN — Receiver 1 input |
| ピン 8 | R2IN — Receiver 2 input |
| ピン 9 | R2OUT — Receiver 2 output |
| ピン 10 | R1OUT — Receiver 1 output |
| ピン 11 | T1IN — Driver 1 input |
| ピン 12 | T2IN — Driver 2 input |
| ピン 13 | T2OUT — Driver 2 output |
| ピン 14 | T1OUT — Driver 1 output |
| ピン 15 | C2 — Charge-pump capacitor connection |
| ピン 16 | C1 — Charge-pump capacitor connection |
主な用途
MAX232DWRG4 の用途: 6 件s: Industrial Control Panels, Data Acquisition Systems, Embedded Serial Port Expansion, Instrumentation and Test Equipment, Point-of-Sale Terminals, Communication and Networking Equipment.
Industrial Control Panels
The MAX232DWRG4 fits industrial control panels that connect a 5 V controller to an RS-232 service port, programming interface, or external instrument. Its two transmitters and two receivers provide two channels in one 16-pin SOIC, while the 120 kbps maximum rate is appropriate for configuration links, command traffic, and moderate data transfers. The commercial 0°C to 70°C range suits controlled indoor equipment. Designers should isolate the RS-232 traces from motors and switching nodes, use the manufacturer-specified charge-pump capacitor connections, and assess whether a protected connector or additional transient suppressor is needed for field-wired cables.
おすすめ
Data Acquisition Systems
The MAX232DWRG4 is useful in laboratory and industrial data-acquisition equipment that must exchange commands and sampled data with a host computer over RS-232. The 120 kbps rate supports low- and moderate-speed acquisition channels, while the dual-channel architecture can connect separate command and data paths. Its single 5 V supply simplifies interfacing with TTL/CMOS logic. For reliable operation, keep the interface connector and cable routing away from high-gain analog inputs, provide a low-impedance return path, and verify the receiver thresholds and line capacitance under the actual cable length and baud-rate conditions.
おすすめ
Embedded Serial Port Expansion
The MAX232DWRG4 allows a modern embedded controller with a limited number of UART channels to connect two RS-232 ports to legacy equipment. Its 120 kbps capability suits configuration, monitoring, and short message-transfer tasks rather than high-throughput continuous streaming. The compact 16-pin SOIC simplifies routing on a mixed-signal embedded board, while the integrated dual-driver and dual-receiver arrangement reduces the number of separate interface devices. Firmware and hardware designers should expose separate enable or multiplexing controls where required, verify logic levels, and test the complete link for startup transients and cable-induced noise.
おすすめ
Instrumentation and Test Equipment
The MAX232DWRG4 is appropriate for test and measurement instruments that expose a PC-compatible RS-232 port for commands, calibration data, or diagnostic output. A 5 V supply, 120 kbps throughput, and two full-duplex channels allow one port for control traffic and another for status or measurement data. The 16-pin SOIC package is convenient for compact instruments, but analog and high-impedance measurement sections require careful isolation from digital return currents. Use a solid ground strategy, minimize connector-to-IC routing, and verify transient protection because bench instruments can be connected to user-controlled external cables.
おすすめ
Point-of-Sale Terminals
The MAX232DWRG4 can support legacy point-of-sale peripherals that exchange serial commands through an EIA/TIA-232 connection. Its two transmitters and receivers allow separate communication paths, while the 5 V operation and 120 kbps rate are compatible with many service ports and older transaction peripherals. The commercial temperature range suits indoor terminals. System integrators should account for electrostatic discharge at the user-accessible connector, preserve common-mode margin across grounded and ungrounded equipment, and select cable length and baud rate using a practical RS-232 margin assessment rather than treating the 120 kbps rating as a guaranteed distance.
おすすめ
Communication and Networking Equipment
The MAX232DWRG4 can bridge a 5 V communications controller to an RS-232 management port in routers, switches, and industrial communication equipment. The 120 kbps rate is suitable for configuration, diagnostics, and legacy management traffic, and the dual-channel configuration can support separate command and status links. Place the transceiver near the connector when practical, maintain a continuous signal-ground reference, and keep the RS-232 traces away from Ethernet magnetics, high-speed processors, and switching power stages. For network products, validate the design against the system’s grounding model, surge requirements, and enclosure-level ESD test plan.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX232DWRG4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX232DWR | MAX232DWE4 | MAX232CWE4 | MAX232AWE4 | ST232BDR |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Product Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Two-driver and two-receiver RS-232 interface |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
主な差別化要因
- Documented high-speed RS-232 capability (vs ST232BDR)
- Published interface protection level (vs ST232BDR)
- Single-supply bipolar RS-232 operation (vs MAX232AWE4)
- Two-channel integration in a 16-pin SOIC (vs MAX232DWE4)
設計ノート
Place the charge-pump capacitors at the pins designated C1 and C2 and keep their connections short. Route the two RS-232 driver outputs and receiver inputs directly toward the connector while maintaining separation from precision analog inputs and high-speed digital traces. The SOIC ground lead must connect to a low-impedance plane, and the logic and RS-232 return paths should not share narrow necks.
Keep the MAX232DWRG4 away from switching-regulator inductors, relay coils, motor traces, and high di/dt power paths. A solid ground plane and short charge-pump capacitor connections reduce radiated and conducted coupling. If the RS-232 connector is externally accessible, evaluate a dedicated transient-protection network at the connector because the device’s ±2 kV ESD rating does not automatically cover larger system-level surge events.
Do not treat the 120 kbps rating as a guaranteed cable distance or a guarantee that every receiver threshold will operate with the system’s ground reference. Confirm capacitor values, baud rate, cable capacitance, grounding, and logic levels against the manufacturer application guidance. When substituting another 16-pin device, compare every pin and external capacitor connection rather than relying on the SOIC footprint alone.
コンプライアンス情報
The available product information identifies the commercial-grade MAX232DWRG4 but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. EIA-232-F, TIA-232-F, and V.28 are interface standards rather than environmental-compliance certifications.