MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments
部品番号: MAX232ECDWRG4 ✓ 生産中MAX232ECDWRG4 概要
An RS-232 transceiver is an interface circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, which combines drivers, receivers, charge-pump voltage conversion, and transient protection in one semiconductor package.
The MAX232ECDWRG4 includes two drivers and two receivers, allowing one package to support two RS-232 communication channels. Its single 5 V supply architecture simplifies system power planning, while the integrated charge pump generates the positive and negative voltages required by RS-232 drivers. Operation up to 120 kbit/s makes the device appropriate for legacy serial ports, industrial control links, equipment interfaces, and embedded systems using compatible RS-232 protocols.
IEC 61000-4-2 protection is a key feature for connectors exposed to electrostatic discharge. The protection capability helps reduce system susceptibility to ESD events at the interface boundary, although it does not eliminate the need for correct grounding, cable design, and connector placement. The input circuitry tolerates levels to ±30 V, supporting the voltage stress commonly encountered on RS-232 networks.
Typical uses include PC-compatible serial ports, test equipment, security systems, instrumentation, industrial controllers, and point-of-sale equipment. Two complete driver-receiver sections can also support separate transmit and receive paths or more than one RS-232 port when several devices share the same PCB. The 16-pin SOIC package supports conventional surface-mount assembly and is easy to route on standard industrial-control boards.
Place the two 1.0 uF charge-pump capacitors close to their designated pins, connect the supply and ground pins to low-impedance planes, and route the RS-232 traces away from sensitive analog signals. Confirm that the external capacitor voltage rating and dielectric are suitable for the charge-pump waveform. PCB power and ground handling should account for the charge pump's switching current even though the interface itself is designed for a single 5 V rail.
This product overview combines the verified electrical capabilities, package details, interface standards, application guidance, replacement considerations, and practical layout notes needed to evaluate the MAX232ECDWRG4 for an RS-232 design. It also highlights the distinction between direct pin-compatible replacements and broader functional alternatives when maintaining an existing circuit board.
ドロップイン代替品: MAX232ECDWRG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX232ECDWRG4 (同一形状・フットプリント) — 相違点: Product Type, Package, Interface Standard, Maximum Data Rate, Number of Receivers.
MAX232ECDWR
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX232ESE+T
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX232IDR
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX232EESE
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MAX232CWE+
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MAX232ECDWRG4 仕様
| Number of Drivers | 2 drivers |
| Number of Receivers | 2 receivers |
| インターフェースタイプ | RS-232 transceiver |
| データレート | 120 kbit/s |
| 電源電圧 | 5 V |
| Charge-Pump Capacitor Value | 1.0 uF each |
| Receiver Input Voltage Range | -30 V to +30 V |
| ESD Protection Standard | IEC 61000-4-2 |
| RS-232 Compliance | TIA/RS-232-F and ITU Recommendation V.28 |
| Package Pin Count | 16 pins |
| Package Type | 16-pin SOIC |
| 動作温度範囲 | 0 C to +70 C |
| 実装タイプ | Surface mount |
MAX232ECDWRG4 16-pin soic ピン配置ガイド
MAX232ECDWRG4 (16-pin soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX232ECDWRG4.
詳細は データシート をご参照ください。
主な用途
MAX232ECDWRG4 の用途: 6 件s: Legacy PC Serial Interfaces, Industrial Control Equipment, Test and Measurement Instruments, Point-of-Sale Terminals, Security and Access Systems, Embedded Service and Debug Ports.
Legacy PC Serial Interfaces
The MAX232ECDWRG4 is appropriate for legacy PC-compatible RS-232 ports because it combines two transmitters and two receivers in a 16-pin SOIC while operating from one 5 V supply. The 120 kbit/s maximum rate covers common UART links used by data-acquisition equipment, programmers, and service equipment. Its integrated charge pump eliminates separate positive and negative RS-232 power rails. Place the 1.0 uF charge-pump capacitors close to their pins and route the connector-side traces away from sensitive logic to preserve signal integrity.
おすすめ
Industrial Control Equipment
The MAX232ECDWRG4 fits room-temperature industrial controllers that need an isolated-by-interface RS-232 level shifter for configuration tools or external equipment. Two driver-receiver channels can serve two serial links, while ±30 V receiver-input tolerance improves tolerance to RS-232 transients. The operating range of 0 C to +70 C suits commercial industrial enclosure conditions. IEC 61000-4-2 protection strengthens the connector interface, but grounding, cable routing, and appropriate external protection remain essential in factory environments.
おすすめ
Test and Measurement Instruments
The MAX232ECDWRG4 is useful in test and measurement instruments that communicate through a legacy RS-232 command port. Its 120 kbit/s capability supports the moderate data rates commonly used for instrument control and status reporting. Two transmit and receive sections can reduce the number of interface packages when the instrument has more than one RS-232 connection. A single 5 V supply simplifies internal rail requirements, and the charge-pump capacitors should use stable ceramic types positioned for short current loops.
おすすめ
Point-of-Sale Terminals
The MAX232ECDWRG4 supports point-of-sale peripherals that use RS-232 for receipt printers, scanners, scales, or service terminals. Its two full interface sections can accommodate multiple peripheral connections when each peripheral uses separate direction pairs. The integrated ±30 V-tolerant receivers add margin for cable-borne voltage transients, while IEC 61000-4-2 protection helps the board withstand electrostatic discharge. Keep the external connector and protection network near the board edge to minimize exposed trace length and improve EMI performance.
おすすめ
Security and Access Systems
The MAX232ECDWRG4 is suitable for access-control panels, alarm controllers, and equipment-management interfaces that retain RS-232 service ports. Two driver-receiver channels can support either two ports or separate communication paths within one enclosure. The 5 V operating supply and 120 kbit/s rate match common embedded UART architectures. Because cable-connected access systems may experience ESD events, place the IC interface close to the connector and use a low-impedance ground plane to maintain predictable protection performance.
おすすめ
Embedded Service and Debug Ports
The MAX232ECDWRG4 can provide a service port for embedded equipment that requires a legacy computer-facing RS-232 connection. The device bridges microcontroller UART logic levels to RS-232 while supporting operation to 120 kbit/s, which is sufficient for configuration, diagnostics, and firmware-service traffic. Its 16-pin SOIC package simplifies assembly on control boards. Use short, controlled RS-232 traces, provide a stable charge-pump capacitor network, and avoid sharing connector return paths with sensitive sensor grounding.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX232ECDWRG4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX232ECDWR | MAX232ESE+T | MAX232IDR | MAX232EESE |
|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主な差別化要因
- Integrated ESD protection for the RS-232 interface (vs MAX232CWE)
- Two complete RS-232 channels in one package (vs MAX232ESE+T)
- Wide receiver-input tolerance (vs MAX232IDR)
- Single-supply charge-pump architecture (vs MAX232EESE)
設計ノート
Place both 1.0 uF charge-pump capacitors immediately across their designated pins, using the shortest possible traces. Keep the capacitor return path close to the device ground connection so charge-pump switching current does not share a long path with the RS-232 receiver return. Select ceramic capacitors with adequate DC-bias derating and verify their effective capacitance across the operating temperature range.
Route the external RS-232 connector and cable interface toward the PCB edge, with the MAX232ECDWRG4 positioned near the entry point. Separate connector-side traces from UART logic, clocks, sensors, and precision analog signals. Use a continuous ground reference and avoid routing the RS-232 return beneath high-current or switching nodes. Proper interface placement improves ESD immunity and reduces radiated emissions.
Decouple the 5 V supply at the IC with a local high-frequency ceramic capacitor and provide nearby bulk capacitance for the complete board. The charge-pump stage draws periodic current even though the interface does not require a bipolar supply. Validate the regulator's transient response and keep the supply and ground planes electrically quiet to prevent logic-level disturbance on the UART side.
Do not substitute a functional RS-232 transceiver solely because it uses a 16-pin SOIC; verify driver and receiver assignments, charge-pump capacitor values, enable or shutdown behavior, and supply requirements against the manufacturer datasheet. MAX232 variants can differ in temperature grade and ESD-protection level even when the footprint remains unchanged. Validate the complete UART signal path after substitution.
コンプライアンス情報
The manufacturer material identifies IEC 61000-4-2 ESD protection, TIA/RS-232-F, and ITU Recommendation V.28. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the available manufacturer and distributor records.