Texas Instruments

MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments

MPN: MAX232ECDWRG4 ✓ Aktif
5 V Vdss 16 pins Package
MOQ: 1 |

MAX232ECDWRG4 Genel Bakış

Texas Instruments MAX232ECDWRG4 is a dual RS-232 driver and receiver interface IC with two transmit channels, two receive channels, and IEC 61000-4-2 protection. It operates from a single 5 V supply, supports data rates to 120 kbit/s, accepts input levels to ±30 V, and uses 1.0 uF charge-pump capacitors. The device is packaged in a 16-pin SOIC.

An RS-232 transceiver is an interface circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, which combines drivers, receivers, charge-pump voltage conversion, and transient protection in one semiconductor package.

The MAX232ECDWRG4 includes two drivers and two receivers, allowing one package to support two RS-232 communication channels. Its single 5 V supply architecture simplifies system power planning, while the integrated charge pump generates the positive and negative voltages required by RS-232 drivers. Operation up to 120 kbit/s makes the device appropriate for legacy serial ports, industrial control links, equipment interfaces, and embedded systems using compatible RS-232 protocols.

IEC 61000-4-2 protection is a key feature for connectors exposed to electrostatic discharge. The protection capability helps reduce system susceptibility to ESD events at the interface boundary, although it does not eliminate the need for correct grounding, cable design, and connector placement. The input circuitry tolerates levels to ±30 V, supporting the voltage stress commonly encountered on RS-232 networks.

Typical uses include PC-compatible serial ports, test equipment, security systems, instrumentation, industrial controllers, and point-of-sale equipment. Two complete driver-receiver sections can also support separate transmit and receive paths or more than one RS-232 port when several devices share the same PCB. The 16-pin SOIC package supports conventional surface-mount assembly and is easy to route on standard industrial-control boards.

Place the two 1.0 uF charge-pump capacitors close to their designated pins, connect the supply and ground pins to low-impedance planes, and route the RS-232 traces away from sensitive analog signals. Confirm that the external capacitor voltage rating and dielectric are suitable for the charge-pump waveform. PCB power and ground handling should account for the charge pump's switching current even though the interface itself is designed for a single 5 V rail.

This product overview combines the verified electrical capabilities, package details, interface standards, application guidance, replacement considerations, and practical layout notes needed to evaluate the MAX232ECDWRG4 for an RS-232 design. It also highlights the distinction between direct pin-compatible replacements and broader functional alternatives when maintaining an existing circuit board.

Drop-in alternatifler için MAX232ECDWRG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller MAX232ECDWRG4 (aynı form faktörü ve ayağa oturma) — farklı olan Product Type, Package, Interface Standard, Maximum Data Rate, Number of Receivers.

Analog Devices
Product Type: RS-232 line driver/receiver transceiver
Package: 16-pin wide SOIC
Interface Standard: RS-232; EIA/TIA-232E and V.28/V.24 family application
İle Karşılaştır MAX232ECDWRG4 →
Texas Instruments
Product Type: Dual RS-232 driver/receiver
Package: 16-pin SOIC (DW), 0.295 inch / 7.50 mm width
Maximum Data Rate: 250 kbps
İle Karşılaştır MAX232ECDWRG4 →
Texas Instruments
Product Type: Dual RS-232 driver and receiver transceiver
Package: 16-SOIC, 7.50 mm width
Interface Standard: TIA/EIA-232-F
İle Karşılaştır MAX232ECDWRG4 →
Analog Devices
Product Type: RS-232 transceiver interface IC
Package: 16-pin SOIC
Interface Standard: EIA/TIA-232E and CCITT V.28
İle Karşılaştır MAX232ECDWRG4 →
Texas Instruments
Product Type: Dual RS-232 transceiver
Package: 16-pin SOIC
Interface Standard: RS-232 / EIA-232
İle Karşılaştır MAX232ECDWRG4 →

MAX232ECDWR

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Texas Instruments
📦 SOIC-16
Dual RS-232 driver/receiver · 2 · 2 · 250 kbps · 4.5 V to 5.5 V · Single 5 V supply · IEC 61000-4-2 · 16-pin SOIC (DW), 0.295 inch / 7.50 mm width

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232ESE+T

✅ Yerleştirme
Analog Devices
📦 SOIC-16
RS-232 transceiver interface IC · 2 drivers and 2 receivers · 4.5 V to 5.5 V · 120 kbps · EIA/TIA-232E and CCITT V.28 · V.28 and V.24 · On-chip capacitive voltage generator · 16 pins

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232IDR

✅ Yerleştirme
Texas Instruments
📦 SOIC-16
Dual RS-232 transceiver · 2 · 2 · 120 kbit/s · 4.5 V to 5.5 V · 5 V · Approximately ±9 V · ±30 V

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232EESE

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 SOIC-16
Same MAX232 16-pin SOIC interface and 5 V charge-pump architecture, with a different temperature-grade suffix; approximately 90% of principal electrical ratings are shared.

📋 Katalogda Olmayan Referans Alternatifi

MAX232CWE+

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Analog Devices
📦 SOIC-16
RS-232 line driver/receiver transceiver · 4.5 V to 5.5 V · 2 · 2 · RS-232; EIA/TIA-232E and V.28/V.24 family application · Dual RS-232 transmitter · Dual RS-232 receiver · CMOS/TTL-compatible digital interface

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MAX232ECDWRG4 Özellikler

Number of Drivers 2 drivers
Number of Receivers 2 receivers
Arayüz Türü RS-232 transceiver
Veri Hızı 120 kbit/s
Besleme Gerilimi 5 V
Charge-Pump Capacitor Value 1.0 uF each
Receiver Input Voltage Range -30 V to +30 V
ESD Protection Standard IEC 61000-4-2
RS-232 Compliance TIA/RS-232-F and ITU Recommendation V.28
Package Pin Count 16 pins
Package Type 16-pin SOIC
İşletim Sıcaklığı Aralığı 0 C to +70 C
Montaj Türü Surface mount

MAX232ECDWRG4 16-pin soic Pin Yapısı Kılavuzu

MAX232ECDWRG4 (16-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

16-pin soic paket pin çizelgesi için MAX232ECDWRG4

Ayrıntılı pin çıkış verisi mevcut değil: MAX232ECDWRG4.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

MAX232ECDWRG4 için uygundur 6 uygulamas: Legacy PC Serial Interfaces, Industrial Control Equipment, Test and Measurement Instruments, Point-of-Sale Terminals, Security and Access Systems, Embedded Service and Debug Ports.

🖥️

Legacy PC Serial Interfaces

The MAX232ECDWRG4 is appropriate for legacy PC-compatible RS-232 ports because it combines two transmitters and two receivers in a 16-pin SOIC while operating from one 5 V supply. The 120 kbit/s maximum rate covers common UART links used by data-acquisition equipment, programmers, and service equipment. Its integrated charge pump eliminates separate positive and negative RS-232 power rails. Place the 1.0 uF charge-pump capacitors close to their pins and route the connector-side traces away from sensitive logic to preserve signal integrity.

🏭

Industrial Control Equipment

The MAX232ECDWRG4 fits room-temperature industrial controllers that need an isolated-by-interface RS-232 level shifter for configuration tools or external equipment. Two driver-receiver channels can serve two serial links, while ±30 V receiver-input tolerance improves tolerance to RS-232 transients. The operating range of 0 C to +70 C suits commercial industrial enclosure conditions. IEC 61000-4-2 protection strengthens the connector interface, but grounding, cable routing, and appropriate external protection remain essential in factory environments.

📟

Test and Measurement Instruments

The MAX232ECDWRG4 is useful in test and measurement instruments that communicate through a legacy RS-232 command port. Its 120 kbit/s capability supports the moderate data rates commonly used for instrument control and status reporting. Two transmit and receive sections can reduce the number of interface packages when the instrument has more than one RS-232 connection. A single 5 V supply simplifies internal rail requirements, and the charge-pump capacitors should use stable ceramic types positioned for short current loops.

🖨️

Point-of-Sale Terminals

The MAX232ECDWRG4 supports point-of-sale peripherals that use RS-232 for receipt printers, scanners, scales, or service terminals. Its two full interface sections can accommodate multiple peripheral connections when each peripheral uses separate direction pairs. The integrated ±30 V-tolerant receivers add margin for cable-borne voltage transients, while IEC 61000-4-2 protection helps the board withstand electrostatic discharge. Keep the external connector and protection network near the board edge to minimize exposed trace length and improve EMI performance.

📷

Security and Access Systems

The MAX232ECDWRG4 is suitable for access-control panels, alarm controllers, and equipment-management interfaces that retain RS-232 service ports. Two driver-receiver channels can support either two ports or separate communication paths within one enclosure. The 5 V operating supply and 120 kbit/s rate match common embedded UART architectures. Because cable-connected access systems may experience ESD events, place the IC interface close to the connector and use a low-impedance ground plane to maintain predictable protection performance.

🔧

Embedded Service and Debug Ports

The MAX232ECDWRG4 can provide a service port for embedded equipment that requires a legacy computer-facing RS-232 connection. The device bridges microcontroller UART logic levels to RS-232 while supporting operation to 120 kbit/s, which is sufficient for configuration, diagnostics, and firmware-service traffic. Its 16-pin SOIC package simplifies assembly on control boards. Use short, controlled RS-232 traces, provide a stable charge-pump capacitor network, and avoid sharing connector return paths with sensitive sensor grounding.

What is the MAX232ECDWRG4?
The MAX232ECDWRG4 is a Texas Instruments dual RS-232 driver and receiver IC with two transmit channels, two receive channels, and IEC 61000-4-2 protection. According to the manufacturer datasheet, it operates from a single 5 V supply, supports rates to 120 kbit/s, accepts receiver inputs to ±30 V, and requires 1.0 uF charge-pump capacitors. It is housed in a 16-pin SOIC package.
What are the key specifications of MAX232ECDWRG4?
The MAX232ECDWRG4 combines two RS-232 drivers, two receivers, a 120 kbit/s maximum data rate, and a single 5 V supply in a 16-pin SOIC. The manufacturer datasheet also identifies ±30 V receiver-input capability and IEC 61000-4-2 ESD protection. Its integrated charge pump uses two 1.0 uF capacitors to support the bipolar voltage levels required by conventional RS-232 signaling.
Where can I download the MAX232ECDWRG4 datasheet PDF?
The MAX232ECDWRG4 datasheet is available through the Texas Instruments document link listed on this page and through the linked PDF catalog entry. The manufacturer document covers the electrical characteristics, charge-pump circuit, RS-232 driver and receiver behavior, ESD protection, pin descriptions, and recommended operating conditions. Use the manufacturer version for design verification and compliance with the published limits.
Where can I find the MAX232ECDWRG4 pinout?
The MAX232ECDWRG4 pinout is shown in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses a 16-pin SOIC package with dedicated driver outputs, receiver inputs, charge-pump connections, supply, and ground pins. Use the numbered package drawing and pin-description table when assigning PCB nets because exposed-pad or alternate-package variants have different layouts.
Can MAX232ECDWRG4 replace a standard MAX232 interface IC?
The MAX232ECDWRG4 can replace a compatible 16-pin SOIC MAX232 design only when the replacement uses the same pin arrangement, 5 V supply, 1.0 uF charge-pump capacitors, and acceptable temperature grade. Its ESD-protection feature and commercial operating range of 0 C to +70 C are the principal selection checks. Confirm pin functions and charge-pump capacitor values against the manufacturer datasheet before production use.
What is the difference between MAX232ECDWRG4 and MAX232ESE+T?
The MAX232ECDWRG4 is specified as a commercial-temperature 16-pin SOIC RS-232 transceiver with IEC 61000-4-2 protection, while the MAX232ESE+T is a distinct temperature-grade and ordering variant. Both use the familiar MAX232 dual-driver, dual-receiver architecture, but their exact environmental ratings and protection specifications must be compared before substitution. The manufacturer datasheet provides the definitive operating limits for each MPN.
Is MAX232ECDWRG4 suitable for industrial RS-232 equipment?
The MAX232ECDWRG4 is suitable for commercial-temperature RS-232 equipment rated from 0 C to +70 C, including room-temperature industrial controllers, test instruments, and legacy peripheral interfaces. Its 120 kbit/s capability and ±30 V receiver-input tolerance support conventional RS-232 links. For wider industrial temperature requirements, select a part with an explicitly wider rated temperature range.
How many RS-232 channels does MAX232ECDWRG4 provide?
The MAX232ECDWRG4 provides two full RS-232 driver and receiver channels in one 16-pin SOIC package. A channel can support one transmit direction and one receive direction, allowing the IC to implement two RS-232 links when both sides are wired appropriately. The manufacturer datasheet identifies two drivers and two receivers and specifies operation up to 120 kbit/s.
Does MAX232ECDWRG4 need an external RS-232 voltage supply?
The MAX232ECDWRG4 does not require separate positive and negative RS-232 supplies. According to the manufacturer datasheet, its integrated charge pump derives the required bipolar voltages from a single 5 V supply using two 1.0 uF capacitors. This reduces external power complexity, although the charge-pump network and its capacitor placement remain important parts of the power and layout design.
What capacitors does MAX232ECDWRG4 require?
The MAX232ECDWRG4 requires two 1.0 uF charge-pump capacitors, as specified by the Texas Instruments manufacturer datasheet. Place each capacitor close to the designated charge-pump pins and use a voltage rating appropriate for the generated waveform. Stable, low-ESR ceramic capacitors with suitable DC-bias characteristics help preserve charge-pump operation and minimize connector-side noise.
How does MAX232ECDWRG4 protect an RS-232 interface from ESD?
The MAX232ECDWRG4 includes protection designed to IEC 61000-4-2 for electrostatic-discharge events at the interface. The protection improves transient tolerance, but it must be combined with a sound system design. Connect the interface ground correctly, keep the RS-232 traces away from sensitive circuitry, and position the protection device where the external cable enters the PCB.
Where can I buy MAX232ECDWRG4 online?
Use the Request a Quote form on this page to request MAX232ECDWRG4 availability, current pricing, minimum order quantity, and lead time. The request identifies the exact Texas Instruments MPN and 16-pin SOIC ordering code, helping procurement confirm the correct commercial-temperature variant rather than a different package, temperature grade, or reel-code configuration.
What is the price of MAX232ECDWRG4?
Current MAX232ECDWRG4 pricing depends on order quantity, market conditions, and requested packaging configuration. Submit the MPN through the Request a Quote form on this page for a current quotation. The form is the appropriate route for checking unit pricing, volume breaks, availability, and lead time without relying on a stale marketplace figure.
What is the lead time for MAX232ECDWRG4?
Lead time for MAX232ECDWRG4 depends on current inventory, order volume, and the manufacturer's production schedule. Request a quote on this page and specify the required quantity and shipment destination for a current commitment. For large or scheduled programs, include the required delivery date so the procurement response can reflect the appropriate supply plan.
Is MAX232ECDWRG4 in stock?
MAX232ECDWRG4 stock status can change quickly and depends on quantity and supply conditions. Use the Request a Quote form on this page to obtain the current availability and a lead-time confirmation for the exact MPN. Include your required quantity, packaging preference, target date, and destination so the quote reflects the procurement request rather than a generic single-unit listing.
When should I choose MAX232ECDWRG4 over another RS-232 transceiver?
Choose the MAX232ECDWRG4 when the design needs two RS-232 drivers and two receivers, a single 5 V supply, operation up to 120 kbit/s, ±30 V receiver-input tolerance, and IEC 61000-4-2 protection in a 16-pin SOIC. Its 0 C to +70 C commercial range makes it appropriate for room-temperature equipment. Choose a wider-temperature or differently protected device when environmental or ESD requirements exceed those limits.

Mühendislik referans verileri: MAX232ECDWRG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the MAX232ECDWRG4 for a 16-pin SOIC RS-232 design that operates from 5 V, needs two transmitters and two receivers, and requires IEC 61000-4-2 protection. Its 120 kbit/s rate and ±30 V receiver-input capability suit conventional RS-232 equipment, while the 0 C to +70 C range targets commercial and room-temperature applications. MAX232ECDWR is the closest ordering variant when only the reel or shipment suffix differs. Consider MAX232ESE+T or MAX232IDR when their temperature grade is appropriate and the exact electrical ratings match. MAX232EESE offers another same-family option, while MAX232CWE may be considered when IEC 61000-4-2 protection is not required. Before replacing any installed device, verify the pin map, charge-pump capacitor values, supply arrangement, and environmental rating in the manufacturer datasheet. For a new design, select the ordering suffix that exactly matches the required package, temperature grade, and shipment method.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MAX232ECDWR MAX232ESE+T MAX232IDR MAX232EESE
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

Ana Farklılayıcılar

  • Integrated ESD protection for the RS-232 interface (karşılaştırma:MAX232CWE)
  • Two complete RS-232 channels in one package (karşılaştırma:MAX232ESE+T)
  • Wide receiver-input tolerance (karşılaştırma:MAX232IDR)
  • Single-supply charge-pump architecture (karşılaştırma:MAX232EESE)

Tasarım Notları

Place both 1.0 uF charge-pump capacitors immediately across their designated pins, using the shortest possible traces. Keep the capacitor return path close to the device ground connection so charge-pump switching current does not share a long path with the RS-232 receiver return. Select ceramic capacitors with adequate DC-bias derating and verify their effective capacitance across the operating temperature range.

Route the external RS-232 connector and cable interface toward the PCB edge, with the MAX232ECDWRG4 positioned near the entry point. Separate connector-side traces from UART logic, clocks, sensors, and precision analog signals. Use a continuous ground reference and avoid routing the RS-232 return beneath high-current or switching nodes. Proper interface placement improves ESD immunity and reduces radiated emissions.

Decouple the 5 V supply at the IC with a local high-frequency ceramic capacitor and provide nearby bulk capacitance for the complete board. The charge-pump stage draws periodic current even though the interface does not require a bipolar supply. Validate the regulator's transient response and keep the supply and ground planes electrically quiet to prevent logic-level disturbance on the UART side.

Do not substitute a functional RS-232 transceiver solely because it uses a 16-pin SOIC; verify driver and receiver assignments, charge-pump capacitor values, enable or shutdown behavior, and supply requirements against the manufacturer datasheet. MAX232 variants can differ in temperature grade and ESD-protection level even when the footprint remains unchanged. Validate the complete UART signal path after substitution.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer material identifies IEC 61000-4-2 ESD protection, TIA/RS-232-F, and ITU Recommendation V.28. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the available manufacturer and distributor records.

Veri doğrulanma tarihi: 2026-11-09 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

MAX232ECDWRG4 datasheet MAX232ECDWRG4 pinout MAX232ECDWRG4 datasheet pdf MAX232ECDWRG4 equivalent MAX232ECDWRG4 replacement MAX232ECDWRG4 cross reference MAX232ECDWRG4 vs MAX232ESE+T MAX232ECDWRG4 price MAX232ECDWRG4 stock Texas Instruments MAX232ECDWRG4 MAX232ECDWRG4 SOIC-16 footprint MAX232ECDWRG4 RS-232 application circuit MAX232ECDWRG4 120 kbit/s MAX232ECDWRG4 IEC 61000-4-2

İlgili Bileşenler ve Terimler

Texas Instruments MAX232ECDWRG4 MAX232ECDWR MAX232ESE+T MAX232IDR MAX232EESE MAX232CWE RS-232 transceiver dual RS-232 driver dual RS-232 receiver RS-232 interface IC UART interface charge-pump voltage converter single 5 V supply IEC 61000-4-2 TIA/RS-232-F ITU Recommendation V.28 RoHS REACH SOIC-16 SOIC package family surface-mount technology electrostatic-discharge protection receiver input voltage data rate
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle