Maxim Integrated

MAX232ECWE+ - 120kbps RS-232 Transceiver | Maxim

部品番号: MAX232ECWE+ ✓ 生産中
4.5 V to 5.5 V Vdss 16-pin SOIC Package
MOQ: 1 |

MAX232ECWE+ 概要

The Maxim Integrated MAX232ECWE+ is a dual RS-232 transceiver with two drivers and two receivers, a 120 kbps data rate, ±15 kV ESD protection, and a single 4.5 V to 5.5 V supply requirement. It is packaged in a 16-pin SOIC and uses an integrated charge pump to generate RS-232 bipolar voltage levels from a 5 V supply.

An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into CMOS or TTL-compatible logic. The MAX232 belongs to the RS-232 transceiver hierarchy, which includes multi-channel transceivers and line-driver and receiver ICs used to connect older serial equipment to modern digital systems.

The device provides two transmit channels and two receive channels in a single package, allowing one RS-232 port to support two directions of data transfer. Its 120 kbps maximum data rate suits conventional asynchronous serial links, while the integrated charge pump removes the need for external ±12 V power. The ±15 kV ESD protection helps improve robustness on cables and connector interfaces exposed to electrostatic discharge.

Operation from a 4.5 V to 5.5 V supply allows use with conventional 5 V digital systems. The transmitter converts CMOS/TTL inputs into RS-232-compatible output levels, while the receivers use threshold and hysteresis to interpret bipolar RS-232 inputs as logic signals. The MAX232E family is specifically designed for RS-232 and V.28 communications, including industrial and instrumentation environments where signal conditioning and interface protection are important.

Typical applications include service-port interfaces, industrial control systems, test and measurement equipment, POS terminals, and embedded systems that need to communicate with legacy RS-232 peripherals. Two driver and two receiver channels also permit two complete RS-232 links when each link requires one transmit and one receive direction.

PCB design should preserve the manufacturer's recommended charge-pump capacitor network and place the associated capacitors close to their designated pins. Keep the interface connector and unprotected logic-side traces separated as far as practical, and route any externally accessible cable shield or ground connection according to the enclosure and system grounding architecture.

This page combines package, interface, purchasing, and replacement information with practical guidance for implementing a robust 5 V RS-232 link. It also identifies genuine pin-compatible options and highlights the temperature-range, lifecycle, and protection considerations that determine whether an alternative can serve as a true drop-in replacement.

ドロップイン代替品: MAX232ECWE+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MAX232ECWE+ (同一形状・フットプリント) — 相違点: Interface Standard, Logic Compatibility, Package, Product Type.

Analog Devices
Interface Standard: RS-232; EIA/TIA-232E and V.28/V.24 family application
Logic Compatibility: CMOS/TTL-compatible digital interface
Package: 16-pin wide SOIC
比較対象 MAX232ECWE+ →
Maxim Integrated
Interface Standard: EIA/TIA-232E
Product Type: Dual RS-232 line driver and receiver transceiver
比較対象 MAX232ECWE+ →

MAX232ESE+

✅ ドロップイン ⚠️ 仕様未検証
Maxim Integrated
📦 16-SOIC
Dual RS-232 line driver and receiver transceiver · 2 channels · 2 channels · 4.5 V to 5.5 V · 120 kbps · EIA/TIA-232E · CCITT V.28 · V.24

価格はお問い合わせください

データシートを見る →

MAX232CWE+

✅ ドロップイン ⚠️ 仕様未検証
Analog Devices
📦 16-SOIC
RS-232 line driver/receiver transceiver · 4.5 V to 5.5 V · 2 · 2 · RS-232; EIA/TIA-232E and V.28/V.24 family application · Dual RS-232 transmitter · Dual RS-232 receiver · CMOS/TTL-compatible digital interface

価格はお問い合わせください

データシートを見る →

MAX232DWE+

✅ ドロップイン ⚠️ 仕様未検証
📦 16-SOIC
Extended-temperature option retains the 120 kbps data rate and 4.5 V to 5.5 V supply, while the operating-temperature grade differs from MAX232ECWE+.

📋 参考代替品(カタログ未掲載)

MAX232EWE

✅ ドロップイン
📦 16-SOIC
Legacy MAX232E option preserves the 120 kbps data rate and 4.5 V to 5.5 V supply, while its lifecycle status is obsolete.

📋 参考代替品(カタログ未掲載)

ST232CDR

✅ ドロップイン
📦 16-SOIC
Provides a 2-driver, 2-receiver RS-232 interface from a 5 V supply at approximately 120 kbps, a 0% data-rate difference; ±15 kV ESD protection is not established for this alternative.

📋 参考代替品(カタログ未掲載)

MAX232ECWE+ 仕様

Transceiver Configuration 2 drivers and 2 receivers
Duplex Mode Full duplex
Communication Standard RS-232 and V.28
Maximum Data Rate 120 kbps
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage +5 V
ESD Protection ±15 kV
Charge Pump Integrated
Logic Compatibility CMOS and TTL
パッケージ 16-pin SOIC
Package Width 7.50 mm
実装タイプ Surface mount

MAX232ECWE+ ピン構成

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
ピン 1 R1OUT — Receiver 1 output
ピン 2 R2OUT — Receiver 2 output
ピン 3 RIN1 — Receiver 1 input
ピン 4 RIN2 — Receiver 2 input
ピン 5 GND — Ground
ピン 6 V+ — Positive charge-pump output
ピン 7 V- — Negative charge-pump output
ピン 8 R2IN — Receiver 2 input
ピン 9 R1IN — Receiver 1 input
ピン 10 T2IN — Driver 2 input
ピン 11 T1IN — Driver 1 input
ピン 12 T1OUT — Driver 1 output
ピン 13 T2OUT — Driver 2 output
ピン 14 VCC — Positive supply input
ピン 15 C2+ — Charge-pump capacitor 2 positive terminal
ピン 16 C1+ — Charge-pump capacitor 1 positive terminal

主な用途

MAX232ECWE+ の用途: 6 件s: Industrial Serial Service Ports, Test and Measurement Equipment, Point-of-Sale Terminal Interfaces, Embedded System Legacy Communication, Security and Surveillance Equipment, Data Acquisition and Control Systems.

🏭

Industrial Serial Service Ports

The MAX232ECWE+ fits industrial service and configuration ports that must translate between a 5 V controller and an RS-232 peripheral. Its two drivers and two receivers provide two full-duplex channels, while the integrated charge pump eliminates the need for external positive and negative RS-232 rails. The 120 kbps rate supports conventional asynchronous service protocols, and ±15 kV ESD protection adds useful robustness on connector-accessible interfaces. Designers should preserve the manufacturer charge-pump capacitor arrangement and verify the exact operating-temperature grade against the enclosure environment.

🔧

Test and Measurement Equipment

The MAX232ECWE+ is appropriate for test instruments that communicate with PCs, service tools, or older automated-test equipment through RS-232. Two transmitters and two receivers allow separate control and result channels, while the 4.5 V to 5.5 V supply range simplifies operation alongside 5 V logic. Its 120 kbps maximum data rate is suitable for typical command and measurement-data links. The integrated charge pump reduces board area, and ±15 kV ESD protection helps protect the instrument when the RS-232 connector is exposed to charged user cables.

🏭

Point-of-Sale Terminal Interfaces

The MAX232ECWE+ can provide the legacy serial interface required by point-of-sale peripherals, receipt equipment, or magnetic-stripe accessories. A 5 V embedded controller can communicate through the MAX232 without separate RS-232 power rails because the charge pump is integrated. The two driver and two receiver channels can support one bidirectional peripheral port plus another auxiliary RS-232 link. At 120 kbps, the interface matches conventional asynchronous equipment rates, while ±15 kV ESD protection is valuable where the external cable reaches a frequently touched or electrically noisy connector.

🧩

Embedded System Legacy Communication

The MAX232ECWE+ bridges modern CMOS or TTL logic and legacy RS-232 equipment without requiring a bipolar supply in the host system. Its full-duplex 2/2 arrangement allows each of two ports to transmit and receive independently, and the 120 kbps rate is suitable for many configuration, logging, and control protocols. The 4.5 V to 5.5 V operating range fits a nominal 5 V rail, while the integrated charge pump simplifies assembly. Firmware designers should confirm that their UART settings, cable length, grounding, and signal levels comply with the selected RS-232 equipment.

🎥

Security and Surveillance Equipment

The MAX232ECWE+ can support service or configuration links on surveillance equipment that retains an RS-232 management interface. The 5 V supply operation and integrated charge pump reduce the external power-conversion requirements of a compact camera or controller board. Its 120 kbps rate is sufficient for administrative commands and status traffic, and ±15 kV ESD protection is useful where an RS-232 cable connects to equipment installed near electrically noisy systems. Installations should still apply cable shielding and proper signal grounding, because interface IC protection does not replace enclosure-level electrostatic controls.

📡

Data Acquisition and Control Systems

The MAX232ECWE+ is useful for connecting a 5 V data-acquisition controller to legacy instrumentation through RS-232. Separate transmit and receive channels support bidirectional command and measurement traffic, while the 120 kbps limit accommodates many slow sensor, laboratory, and process-control protocols. Integrated charge-pump circuitry removes external ±12 V or ±15 V supply requirements, and ±15 kV ESD protection helps the interface withstand discharge events associated with external cabling. For precision measurement systems, keep analog and digital grounding methods consistent and route the interface to avoid sensitive signal paths.

おすすめ製品の概要

What are the key specifications of MAX232ECWE+ that engineers should know?
The MAX232ECWE+ is a 5 V, dual-driver and dual-receiver RS-232 transceiver rated for 120 kbps and protected to ±15 kV ESD. According to the MAX232E/MAX213E manufacturer datasheet, it supports RS-232 and V.28 communication, uses an integrated charge pump, and accepts a 4.5 V to 5.5 V supply. The device is housed in a 16-pin SOIC, making it suitable for compact single-board serial interfaces. Its full-duplex configuration supports two transmit and two receive channels in one package.
What is the operating voltage range of MAX232ECWE+?
The MAX232ECWE+ operates from 4.5 V to 5.5 V and is intended for a nominal +5 V supply. According to the MAX232E/MAX213E manufacturer datasheet, the integrated charge-pump circuitry generates the positive and negative RS-232 voltage levels required by the drivers, so the board does not need a separate bipolar RS-232 supply. Designers should keep the supply within the stated 1 V total range and account for normal 5 V rail tolerance and transient behavior at the IC.
How many RS-232 channels does MAX232ECWE+ provide?
The MAX232ECWE+ provides two RS-232 drivers and two receivers, allowing two full-duplex RS-232 links to share one IC. According to the MAX232E/MAX213E manufacturer datasheet, each link normally requires one driver for outbound data and one receiver for inbound data. This arrangement is useful in service-port adapters, test systems, and embedded controllers that need more than one serial port without adding a second transceiver package.
What is the maximum data rate of MAX232ECWE+?
The MAX232ECWE+ supports a maximum data rate of 120 kbps. According to the MAX232E/MAX213E manufacturer datasheet, the MAX232E family is designed for RS-232 and V.28 links operating from a single 5 V supply. This rate is appropriate for conventional asynchronous serial ports and equipment interfaces; designs requiring substantially higher throughput should use a different RS-232 transceiver architecture.
Where can I download the MAX232ECWE+ datasheet PDF?
The MAX232ECWE+ datasheet PDF is available from Analog Devices and Maxim Integrated through the manufacturer documentation portal. According to the MAX232E/MAX213E manufacturer datasheet, the document covers the electrical characteristics, RS-232 driver and receiver behavior, charge-pump circuitry, ESD ratings, and pin configuration. Use the manufacturer document when assigning PCB pins or selecting capacitors because equivalent-looking RS-232 transceivers can use different charge-pump networks and pin arrangements.
Where is the MAX232ECWE+ pinout and where is pin 1 located?
The MAX232ECWE+ uses a 16-pin SOIC, and pin 1 is located at the top-left end of the package when the pin-1 identifier is oriented upward. According to the MAX232E/MAX213E manufacturer datasheet, the pins include receiver outputs, receiver inputs, driver inputs, driver outputs, supply, ground, charge-pump nodes, and the generated RS-232 rails. Use the package drawing and pin-description table from the manufacturer datasheet when making PCB assignments.
Does MAX232ECWE+ need external positive and negative RS-232 power rails?
No. The MAX232ECWE+ includes an integrated charge pump that produces the required RS-232 voltage levels from one 4.5 V to 5.5 V supply. According to the MAX232E/MAX213E manufacturer datasheet, the charge-pump capacitor connections must still be implemented exactly as shown in the typical application circuit. The device is therefore much simpler to use than a conventional RS-232 transceiver that requires external ±12 V or ±15 V rails.
What is the difference between MAX232ECWE+ and MAX232ESE+?
The principal difference between MAX232ECWE+ and MAX232ESE+ is the temperature grade, while both use a 16-pin SOIC and implement the same 2-transmitter, 2-receiver RS-232 architecture. According to the MAX232E/MAX213E manufacturer datasheet, the MAX232E family uses the same 120 kbps interface concept and integrated charge pump. Because a wider temperature range changes qualification requirements, select the grade that matches the ambient and system conditions rather than treating the suffix difference as interchangeable.
MAX232ECWE+ vs ST232CDR - which is better for a 5 V RS-232 port?
The MAX232ECWE+ is the better documented choice when ±15 kV ESD protection and the Maxim charge-pump implementation are important, while ST232CDR is a cross-brand option for a 5 V RS-232 design. According to the MAX232E/MAX213E manufacturer datasheet, the MAX232ECWE+ provides two drivers, two receivers, a 120 kbps rate, and a 4.5 V to 5.5 V supply range. Verify the ST232CDR pinout, lifecycle status, and protection ratings against its own datasheet before replacing an existing board.
When should I choose MAX232ECWE+ over MAX3232CDBR?
Choose MAX232ECWE+ when a legacy port requires the established MAX232 RS-232 interface and its MAX232E-family pin arrangement, while MAX3232CDBR is appropriate when the design objective is a more modern RS-232 transceiver with integrated power management. The MAX232ECWE+ supports two drivers and two receivers at 120 kbps from a 4.5 V to 5.5 V supply, according to the MAX232E/MAX213E manufacturer datasheet. A MAX3232-family device must not be treated as pin-compatible without checking its exact package and schematic.
Is MAX232ECWE+ suitable for industrial equipment and test instruments?
The MAX232ECWE+ is suitable for many industrial and test-instrument interfaces because it supports RS-232 and V.28 communication, 120 kbps operation, integrated charge-pump circuitry, and ±15 kV ESD protection. According to the MAX232E/MAX213E manufacturer datasheet, the MAX232E family is intended for communications in harsh environments. The exact operating-temperature grade must still be checked against the enclosure temperature and production requirements before environmental qualification is considered complete.
What can replace MAX232ECWE+ as a pin-compatible RS-232 transceiver?
A valid replacement must use the same 16-pin SOIC footprint, preserve the MAX232 pin functions, and remain compatible with the original 4.5 V to 5.5 V supply arrangement. Cross-reference information identifies MAX232ESE+, ST232CDR, and other MAX232-family candidates, but the MAX232ECWE+ and MAX232ESE+ comparison also shows why temperature grade and lifecycle must be considered. Use the manufacturer pin tables before ordering any substitute, and confirm capacitor connections against the replacement datasheet.
Is MAX232ECWE+ the same as MAX232EWE?
The MAX232ECWE+ and MAX232EWE are closely related MAX232 RS-232 transceivers in the same 16-pin SOIC family, but their ordering suffixes indicate different temperature or lifecycle conditions. According to the MAX232E/MAX213E manufacturer datasheet, the core interface is a 2-driver, 2-receiver RS-232/V.28 transceiver operating at up to 120 kbps from a 4.5 V to 5.5 V supply. Confirm the exact suffix status, temperature range, and pin compatibility before using one as a replacement for the other.
Where can I buy MAX232ECWE+ online?
The MAX232ECWE+ can be requested through the Request a Quote form on this product page. The form is the appropriate route for current commercial availability, volume pricing, lead time, and minimum-order requirements. Before requesting a quotation, confirm that the required 16-pin SOIC package, manufacturer marking, operating-temperature grade, and orderable suffix match the target design.
What is the price of MAX232ECWE+ and is it in stock?
Current price and stock status for MAX232ECWE+ should be obtained through the Request a Quote form on this page. The form provides the current commercial response for the exact manufacturer part number and requested quantity. Because availability can change by package, quantity, and production status, confirm the complete suffix and packaging requirements in the quote request rather than relying on a generic RS-232 transceiver listing.
What is the lead time for MAX232ECWE+?
The current lead time for MAX232ECWE+ should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, exact package suffix, and current component availability. Include the required delivery date and production quantity in the request so the commercial response can reflect the actual build schedule.

エンジニアリング参考データ: MAX232ECWE+ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose MAX232ECWE+ for a conventional 5 V RS-232 interface that requires a 16-pin SOIC, 120 kbps operation, two drivers, two receivers, and ±15 kV ESD protection. Select MAX232ESE+ when the same MAX232 pinout and electrical performance are needed but the operating-temperature grade must differ; confirm the grade and lifecycle before ordering. MAX232CWE+ and MAX232DWE+ are useful same-family options for commercial- or extended-temperature production planning. Avoid MAX232EWE for new production because it is obsolete. ST232CDR can serve as a cross-brand 16-SOIC alternative, but its exact pin assignment, ESD rating, lifecycle status, and capacitor network must be checked against its datasheet. MAX3232CDBR should be selected for a redesigned interface rather than treated as a drop-in MAX232 replacement.

代替品との比較

パラメータ この製品 MAX232ESE+ MAX232CWE+ MAX232DWE+ MAX232EWE ST232CDR
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated STMicroelectronics
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers
Maximum Data Rate 120 kbps 120 kbps 120 kbps 120 kbps 120 kbps Approximately 120 kbps
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 5 V operating supply
Charge Pump Integrated Integrated Integrated Integrated Integrated Integrated
Communication Standard RS-232 and V.28 RS-232 and V.28 RS-232 and V.28 RS-232 and V.28 RS-232 and V.28 RS-232 and V.28

主な差別化要因

  • Higher documented connector-side ESD protection rating (vs ST232CDR)
  • Direct same-brand family option with unchanged principal operating parameters (vs MAX232ESE+)
  • Clearer production choice than the obsolete MAX232E suffix (vs MAX232EWE)

設計ノート

Implement the charge-pump capacitor network exactly as shown in the MAX232E/MAX213E manufacturer datasheet. Keep the capacitors close to their associated MAX232ECWE+ pins, use the specified capacitor type and tolerance, and minimize loop area around the charge-pump nodes. Incorrect capacitor values or long return paths can increase ripple, alter startup behavior, and reduce the available RS-232 output margin.

Place the RS-232 connector and transceiver near one another, but keep the protected transceiver side away from sensitive analog or high-speed digital traces. Use the connector ground as the cable-shield reference, maintain a controlled ground return, and avoid routing unprotected logic-side nets beneath long RS-232 traces. The ±15 kV rating is an IC protection feature, not a replacement for enclosure design, shielding, or verified system-level ESD procedures.

Do not treat the RS-232 ground as an interchangeable signal-ground connection for every attached product. Some systems use a floating or isolated RS-232 port, and incorrect tying can create ground-current problems. Verify whether the connected device expects signal ground, chassis ground, or a floating reference before finalizing the board layout. Also confirm the exact MAX232 suffix and temperature grade before treating another MAX232-family order code as a production replacement.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not established by the referenced product information. AEC-Q100 is not applicable because this RS-232 interface IC is not identified as an automotive-qualified device.

データ検証日: 2026-11-17 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MAX232ECWE+ datasheet MAX232ECWE+ pinout MAX232ECWE+ datasheet pdf MAX232ECWE+ equivalent MAX232ECWE+ replacement MAX232ECWE+ cross reference MAX232ECWE+ price MAX232ECWE+ stock Maxim Integrated MAX232ECWE+ MAX232ECWE+ 120kbps RS-232 MAX232ECWE+ 16-SOIC MAX232ECWE+ vs MAX232ESE+ MAX232ECWE+ vs ST232CDR MAX232ECWE+ industrial interface

関連部品&用語

Maxim Integrated MAX232ECWE+ MAX232ESE+ MAX232CWE+ MAX232DWE+ MAX232EWE ST232CDR MAX3232CDBR RS-232 transceiver RS-232 V.28 CMOS TTL integrated charge pump dual driver and dual receiver 120 kbps 4.5 V to 5.5 V ±15 kV ESD protection 16-SOIC SOIC family surface mount industrial control test and measurement equipment data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示