MAX232ECWE+ - 120kbps RS-232 Transceiver | Maxim
부품 번호: MAX232ECWE+ ✓ 활성MAX232ECWE+ 개요
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into CMOS or TTL-compatible logic. The MAX232 belongs to the RS-232 transceiver hierarchy, which includes multi-channel transceivers and line-driver and receiver ICs used to connect older serial equipment to modern digital systems.
The device provides two transmit channels and two receive channels in a single package, allowing one RS-232 port to support two directions of data transfer. Its 120 kbps maximum data rate suits conventional asynchronous serial links, while the integrated charge pump removes the need for external ±12 V power. The ±15 kV ESD protection helps improve robustness on cables and connector interfaces exposed to electrostatic discharge.
Operation from a 4.5 V to 5.5 V supply allows use with conventional 5 V digital systems. The transmitter converts CMOS/TTL inputs into RS-232-compatible output levels, while the receivers use threshold and hysteresis to interpret bipolar RS-232 inputs as logic signals. The MAX232E family is specifically designed for RS-232 and V.28 communications, including industrial and instrumentation environments where signal conditioning and interface protection are important.
Typical applications include service-port interfaces, industrial control systems, test and measurement equipment, POS terminals, and embedded systems that need to communicate with legacy RS-232 peripherals. Two driver and two receiver channels also permit two complete RS-232 links when each link requires one transmit and one receive direction.
PCB design should preserve the manufacturer's recommended charge-pump capacitor network and place the associated capacitors close to their designated pins. Keep the interface connector and unprotected logic-side traces separated as far as practical, and route any externally accessible cable shield or ground connection according to the enclosure and system grounding architecture.
This page combines package, interface, purchasing, and replacement information with practical guidance for implementing a robust 5 V RS-232 link. It also identifies genuine pin-compatible options and highlights the temperature-range, lifecycle, and protection considerations that determine whether an alternative can serve as a true drop-in replacement.
드롭인 대체품: MAX232ECWE+ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX232ECWE+ (동일 폼 팩터 및 풋프린트) — 차이점: Interface Standard, Logic Compatibility, Package, Product Type.
MAX232ESE+
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232CWE+
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MAX232DWE+
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MAX232EWE
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ST232CDR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX232ECWE+ 사양
| Transceiver Configuration | 2 drivers and 2 receivers |
| Duplex Mode | Full duplex |
| Communication Standard | RS-232 and V.28 |
| Maximum Data Rate | 120 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | +5 V |
| ESD Protection | ±15 kV |
| Charge Pump | Integrated |
| Logic Compatibility | CMOS and TTL |
| 패키지 | 16-pin SOIC |
| Package Width | 7.50 mm |
| 실장 유형 | Surface mount |
MAX232ECWE+ 핀 구성
| 핀 1 | R1OUT — Receiver 1 output |
| 핀 2 | R2OUT — Receiver 2 output |
| 핀 3 | RIN1 — Receiver 1 input |
| 핀 4 | RIN2 — Receiver 2 input |
| 핀 5 | GND — Ground |
| 핀 6 | V+ — Positive charge-pump output |
| 핀 7 | V- — Negative charge-pump output |
| 핀 8 | R2IN — Receiver 2 input |
| 핀 9 | R1IN — Receiver 1 input |
| 핀 10 | T2IN — Driver 2 input |
| 핀 11 | T1IN — Driver 1 input |
| 핀 12 | T1OUT — Driver 1 output |
| 핀 13 | T2OUT — Driver 2 output |
| 핀 14 | VCC — Positive supply input |
| 핀 15 | C2+ — Charge-pump capacitor 2 positive terminal |
| 핀 16 | C1+ — Charge-pump capacitor 1 positive terminal |
일반적인 애플리케이션
MAX232ECWE+ 적합 용도: 6 애플리케이션s: Industrial Serial Service Ports, Test and Measurement Equipment, Point-of-Sale Terminal Interfaces, Embedded System Legacy Communication, Security and Surveillance Equipment, Data Acquisition and Control Systems.
Industrial Serial Service Ports
The MAX232ECWE+ fits industrial service and configuration ports that must translate between a 5 V controller and an RS-232 peripheral. Its two drivers and two receivers provide two full-duplex channels, while the integrated charge pump eliminates the need for external positive and negative RS-232 rails. The 120 kbps rate supports conventional asynchronous service protocols, and ±15 kV ESD protection adds useful robustness on connector-accessible interfaces. Designers should preserve the manufacturer charge-pump capacitor arrangement and verify the exact operating-temperature grade against the enclosure environment.
추천
Test and Measurement Equipment
The MAX232ECWE+ is appropriate for test instruments that communicate with PCs, service tools, or older automated-test equipment through RS-232. Two transmitters and two receivers allow separate control and result channels, while the 4.5 V to 5.5 V supply range simplifies operation alongside 5 V logic. Its 120 kbps maximum data rate is suitable for typical command and measurement-data links. The integrated charge pump reduces board area, and ±15 kV ESD protection helps protect the instrument when the RS-232 connector is exposed to charged user cables.
추천
Point-of-Sale Terminal Interfaces
The MAX232ECWE+ can provide the legacy serial interface required by point-of-sale peripherals, receipt equipment, or magnetic-stripe accessories. A 5 V embedded controller can communicate through the MAX232 without separate RS-232 power rails because the charge pump is integrated. The two driver and two receiver channels can support one bidirectional peripheral port plus another auxiliary RS-232 link. At 120 kbps, the interface matches conventional asynchronous equipment rates, while ±15 kV ESD protection is valuable where the external cable reaches a frequently touched or electrically noisy connector.
추천
Embedded System Legacy Communication
The MAX232ECWE+ bridges modern CMOS or TTL logic and legacy RS-232 equipment without requiring a bipolar supply in the host system. Its full-duplex 2/2 arrangement allows each of two ports to transmit and receive independently, and the 120 kbps rate is suitable for many configuration, logging, and control protocols. The 4.5 V to 5.5 V operating range fits a nominal 5 V rail, while the integrated charge pump simplifies assembly. Firmware designers should confirm that their UART settings, cable length, grounding, and signal levels comply with the selected RS-232 equipment.
추천
Security and Surveillance Equipment
The MAX232ECWE+ can support service or configuration links on surveillance equipment that retains an RS-232 management interface. The 5 V supply operation and integrated charge pump reduce the external power-conversion requirements of a compact camera or controller board. Its 120 kbps rate is sufficient for administrative commands and status traffic, and ±15 kV ESD protection is useful where an RS-232 cable connects to equipment installed near electrically noisy systems. Installations should still apply cable shielding and proper signal grounding, because interface IC protection does not replace enclosure-level electrostatic controls.
추천
Data Acquisition and Control Systems
The MAX232ECWE+ is useful for connecting a 5 V data-acquisition controller to legacy instrumentation through RS-232. Separate transmit and receive channels support bidirectional command and measurement traffic, while the 120 kbps limit accommodates many slow sensor, laboratory, and process-control protocols. Integrated charge-pump circuitry removes external ±12 V or ±15 V supply requirements, and ±15 kV ESD protection helps the interface withstand discharge events associated with external cabling. For precision measurement systems, keep analog and digital grounding methods consistent and route the interface to avoid sensitive signal paths.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX232ECWE+ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX232ESE+ | MAX232CWE+ | MAX232DWE+ | MAX232EWE | ST232CDR |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | STMicroelectronics |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps | 120 kbps | 120 kbps | Approximately 120 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 5 V operating supply |
| Charge Pump | Integrated | Integrated | Integrated | Integrated | Integrated | Integrated |
| Communication Standard | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 | RS-232 and V.28 |
주요 차별점
- Higher documented connector-side ESD protection rating (vs ST232CDR)
- Direct same-brand family option with unchanged principal operating parameters (vs MAX232ESE+)
- Clearer production choice than the obsolete MAX232E suffix (vs MAX232EWE)
설계 노트
Implement the charge-pump capacitor network exactly as shown in the MAX232E/MAX213E manufacturer datasheet. Keep the capacitors close to their associated MAX232ECWE+ pins, use the specified capacitor type and tolerance, and minimize loop area around the charge-pump nodes. Incorrect capacitor values or long return paths can increase ripple, alter startup behavior, and reduce the available RS-232 output margin.
Place the RS-232 connector and transceiver near one another, but keep the protected transceiver side away from sensitive analog or high-speed digital traces. Use the connector ground as the cable-shield reference, maintain a controlled ground return, and avoid routing unprotected logic-side nets beneath long RS-232 traces. The ±15 kV rating is an IC protection feature, not a replacement for enclosure design, shielding, or verified system-level ESD procedures.
Do not treat the RS-232 ground as an interchangeable signal-ground connection for every attached product. Some systems use a floating or isolated RS-232 port, and incorrect tying can create ground-current problems. Verify whether the connected device expects signal ground, chassis ground, or a floating reference before finalizing the board layout. Also confirm the exact MAX232 suffix and temperature grade before treating another MAX232-family order code as a production replacement.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not established by the referenced product information. AEC-Q100 is not applicable because this RS-232 interface IC is not identified as an automotive-qualified device.