MAX312CAE - Quad SPST 10Ω CMOS Switch | Analog Devices
部品番号: MAX312CAE ✓ 生産中MAX312CAE 概要
A CMOS analog switch is a semiconductor device that uses controlled transistors to connect or disconnect an analog signal path. Within the broader hierarchy, an analog switch is an interface IC used for signal routing, multiplexing, demultiplexing, and test-signal selection. Unlike mechanical relays, it provides electronic switching without moving contacts and can be controlled by digital logic while preserving the selected signal's voltage range.
The MAX312 family's principal electrical features include an on-resistance of 10Ω maximum, channel-to-channel on-resistance matching of 1.5Ω maximum, and low leakage of 2.5nA at +85°C. The product page also identifies rail-to-rail signal handling, single-supply operation from +4.5V to +30V, and dual-supply operation from ±4.5V to ±20V. These ratings make the family suitable for systems that route signals across a broad common-mode range.
The MAX312/MAX313/MAX314 family is documented with a maximum ESD protection rating greater than 2000V per Method 3015.7 and crosstalk above 96dB at 20kHz. The Analog Devices product page identifies pin compatibility with the DG411, DG412, and DG413 families. On-resistance matching is particularly useful when multiple channels must present similar impedance to a precision measurement or signal-conditioning circuit.
Typical uses include multiplexed sensor acquisition, instrumentation signal routing, test-equipment channel selection, data-acquisition systems, and general analog signal isolation. The switch can be used with a single supply or split supply, allowing integration into circuits that operate from a positive-only rail as well as systems requiring bipolar signal paths. Its 10Ω maximum resistance should be included in the design budget when driving high-impedance versus low-impedance downstream networks.
For layout, route high-impedance signals directly to the relevant switch terminals and keep sensitive traces away from switching nodes and fast external clocks. Check the complete on-resistance curve for the selected signal voltage, because the published 10Ω value is a maximum rather than a constant resistance at every voltage and temperature.
This page combines the manufacturer’s electrical and capability specifications, practical signal-routing considerations, and verified same-family replacement guidance. It also distinguishes documented functions from parameters that must be confirmed in the manufacturer datasheet before production release.
ドロップイン代替品: MAX312CAE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MAX313CAE
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX314CAE
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX312CAE 最大定格&電気的特性
| Switch Type | Quad SPST analog switch |
| Number of Channels | 4 channels |
| On-Resistance | 10Ω maximum |
| On-Resistance Matching Between Channels | 1.5Ω maximum |
| Leakage Current | 2.5nA at +85°C |
| Single-Supply Voltage Range | +4.5V to +30V |
| Dual-Supply Voltage Range | ±4.5V to ±20V |
| Signal Handling | Rail-to-rail |
| ESD Protection | Greater than 2000V per Method 3015.7 |
| Crosstalk | Greater than 96dB at 20kHz |
| Signal Conduction Direction | Bidirectional |
| Technology | CMOS |
| Pin Compatibility | Compatible with DG411, DG412, and DG413 |
| Package Pin Count | 12 pins |
| Production Status | Production |
MAX312CAE 12 pins ピン配置ガイド
MAX312CAE (12 pins パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX312CAE.
詳細は データシート をご参照ください。
主な用途
MAX312CAE の用途: 6 件s: Multiplexed Sensor Acquisition, Precision Instrumentation Signal Routing, Data-Acquisition Channel Selection, Test and Measurement Signal Selection, Battery-Powered Analog Interface, Analog Signal Isolation.
Multiplexed Sensor Acquisition
The MAX312CAE can route several analog sensor outputs into a shared measurement chain through its four SPST channels. Its 10Ω maximum on-resistance is manageable for high-impedance sensor and instrumentation inputs, while the 1.5Ω maximum matching between channels helps reduce gain variation when channels are selected sequentially. Place the switch close to the multiplexer node and include its contribution in the sensor error budget. Leakage of 2.5nA at +85°C is particularly relevant for high-impedance sources, so the complete acquisition path should be checked for temperature-dependent bias error.
おすすめ
Precision Instrumentation Signal Routing
The MAX312CAE supports rail-to-rail signal handling and configurable single- or dual-supply operation, making it suitable for routing measurements between amplifier, filter, and converter stages. The maximum on-resistance of 10Ω and maximum channel-to-channel matching of 1.5Ω should be included when calculating attenuation and gain error. With high-impedance amplifier inputs, the leakage specification of 2.5nA at +85°C helps define achievable accuracy. Keep sensitive nodes away from adjacent switching paths, and use short traces to limit pickup from external clocks or fast digital control signals.
おすすめ
Data-Acquisition Channel Selection
Four independent MAX312CAE switches can select multiple analog inputs before an ADC, allowing a compact acquisition front end without a separate relay for every source. The device operates from +4.5V to +30V for single-supply systems or ±4.5V to ±20V for bipolar systems, accommodating both ground-referenced and centered signal ranges. Account for the 10Ω maximum series resistance during sample-and-hold settling calculations, especially when driving a lower-impedance ADC input. The 1.5Ω maximum matching between channels can simplify calibration because selected channels present similar resistance.
おすすめ
Test and Measurement Signal Selection
The MAX312CAE is suitable for connecting test signals, references, or stimulus sources to a shared measurement amplifier while preserving rail-to-rail signal handling. Bidirectional conduction allows the selected path to carry signals in either direction, simplifying fixture routing. The 10Ω maximum on-resistance must be included in source loading calculations, and the 1.5Ω maximum channel matching can reduce test-path variation. Use a controlled ground reference and place bypass capacitors near the supply pins. Avoid routing high-energy or high-voltage nodes adjacent to the switch terminals because the device is intended for low-voltage CMOS signal routing.
おすすめ
Battery-Powered Analog Interface
A single +4.5V to +30V supply configuration lets the MAX312CAE support signal routing in battery-derived systems that cannot provide a negative rail. The rail-to-rail capability allows signals to use much of the available supply range, while four SPST switches provide compact channel isolation. Designers should verify the control thresholds against the system’s supply voltage and confirm the signal amplitude remains within the absolute maximum ratings. Because the family’s leakage is specified as 2.5nA at +85°C, assess source-loading effects for high-impedance sensors throughout the intended temperature range.
おすすめ
Analog Signal Isolation
The MAX312CAE can disconnect unwanted loads, isolate a source during measurement, or establish a defined signal path within a larger analog system. Its bidirectional operation is useful for paths where signal direction can reverse, and the 10Ω maximum on-resistance gives designers a defined upper bound for series-loss analysis. When the switch isolates a high-impedance node, account for leakage and any capacitance formed by adjacent routes. Keep control traces away from sensitive analog nodes and verify the switch-off behavior across the complete temperature range used by the equipment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX312CAE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX313CAE | MAX314CAE |
|---|---|---|---|
| Package | 12-pin package | 12-pin package | 12-pin package |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Switch Configuration | Quad SPST | Quad SPST | Quad SPST |
| Maximum On-Resistance | 10Ω | 10Ω | 10Ω |
| On-Resistance Matching Between Channels | 1.5Ω maximum | 1.5Ω maximum | 1.5Ω maximum |
| Leakage Current | 2.5nA at +85°C | 2.5nA at +85°C | 2.5nA at +85°C |
| Single-Supply Operation | +4.5V to +30V | +4.5V to +30V | +4.5V to +30V |
| Dual-Supply Operation | ±4.5V to ±20V | ±4.5V to ±20V | ±4.5V to ±20V |
| Signal Handling | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Control Logic | MAX312 family control logic | MAX313 family control logic | MAX314 family control logic |
主な差別化要因
- Maintains the same maximum on-resistance across the documented same-family choices (vs MAX313CAE)
- Preserves channel-to-channel resistance matching (vs MAX314CAE)
- Supports both positive-only and bipolar system architectures (vs MAX313CAE)
設計ノート
Treat the 10Ω maximum on-resistance as a series element in the complete signal path. For a high-impedance receiver, its effect may be negligible, but it becomes important when the selected source has a lower impedance or when the path drives an ADC sample-and-hold input. Use the manufacturer on-resistance curve for the actual signal voltage and temperature rather than assuming that 10Ω applies at every operating point.
Keep the common terminals, signal terminals, and control pins close to their intended circuit nodes, and avoid routing sensitive analog traces directly beside switching terminals. Place supply bypass capacitance near the device supply pins and return it to the local ground reference. If control signals originate near a fast digital processor, use controlled impedance routing and consider a ground guard where the board area permits it.
Do not select a same-family replacement solely from its package and on-resistance rating. MAX313CAE and MAX314CAE match the MAX312CAE family's key resistance and leakage specifications, but control-input thresholds and truth-table behavior determine whether they are electrically interchangeable. Verify the control logic, supply arrangement, absolute maximum ratings, and package drawing before approving a substitution.
コンプライアンス情報
The MAX312 family is a production analog interface IC, but specific environmental and material-compliance declarations for MAX312CAE are not stated on the cited product page. AEC-Q100 status is marked not applicable because no automotive qualification is identified.