MAX3232ECDW - 3-5.5V RS-232 Transceiver | Texas Instruments
部品番号: MAX3232ECDW ✓ 生産中MAX3232ECDW 概要
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts received RS-232 signals back into logic levels. It belongs to the hierarchy of serial-interface transceivers, communication interface ICs, and semiconductor interface devices. The MAX3232E family also integrates a dual charge pump, allowing operation from a single 3 V to 5.5 V supply without a separate negative supply rail.
The device provides two RS-232 transmitters and two RS-232 receivers in a 16-pin SOIC package. Its operating supply range of 3 V to 5.5 V supports both 3.3 V and 5 V system environments. Pin-to-pin IEC ESD protection of ±15 kV applies to the serial-port connection pins, including ground, improving interface robustness in electrically noisy installations.
According to the Texas Instruments MAX3232E product page, the MAX3232E meets TIA/EIA-232-F requirements. The integrated dual charge pump generates the positive and negative voltages required for RS-232 signaling while keeping the external power-supply requirement to a single positive rail. The interface separates external line-side signals from the logic-side circuitry used by UART and other asynchronous controllers.
Typical uses include industrial serial adapters, barcode readers, test and measurement equipment, security consoles, and embedded systems that retain an RS-232 port. The device is particularly suitable when a modern 3.3 V controller must communicate with legacy RS-232 equipment through a compact, surface-mount interface. Its 16-pin SOIC package also simplifies assembly and inspection in designs that do not require an extended-voltage transceiver.
Decoupling capacitor placement is critical to charge-pump performance. Follow the manufacturer datasheet when placing the charge-pump fly capacitors, supply bypass capacitor, and connector-side protection network. Keep the serial traces short, route them away from clocks and switching nodes, and provide a low-impedance ground return between the transceiver and connector.
This page combines electrical specifications, pin-level guidance, drop-in cross-references, and application-focused design notes. It helps engineers distinguish the MAX3232ECDW from related MAX3232E and MAX3232C variants while preserving the same 16-pin SOIC board footprint during sourcing or redesign.
ドロップイン代替品: MAX3232ECDW — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX3232ECDW (同一形状・フットプリント) — 相違点: Product Type, Package, ESD Protection, Maximum Data Rate, External Charge-Pump Capacitors.
MAX3232EIDWR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX3232ECWE+
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3232CDW
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3232CPWR
✅ ドロップイン価格はお問い合わせください
データシートを見る →SP3232EBCN-L/TR
✅ ドロップイン✓ 在庫あり
$0.7711 / 個
データシートを見る →MAX3232ECDW 仕様
| Product Type | RS-232 line-driver and receiver transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Interface Standard | RS-232 |
| Compliance Standard | TIA/EIA-232-F |
| ESD Protection | ±15 kV IEC pin-to-pin |
| Charge Pump | Integrated dual charge pump |
| Logic Supply Requirement | Single 3 V to 5.5 V supply |
| パッケージ | 16-pin SOIC |
| Package Dimensions | 7.50 mm body width |
| 実装タイプ | Surface mount |
| ピン数 | 16 pins |
MAX3232ECDW ピン構成
| ピン 1 | C1+ — Charge-pump capacitor 1 positive terminal |
| ピン 2 | V+ — Charge-pump positive output |
| ピン 3 | C1- — Charge-pump capacitor 1 negative terminal |
| ピン 4 | C2+ — Charge-pump capacitor 2 positive terminal |
| ピン 5 | C2- — Charge-pump capacitor 2 negative terminal |
| ピン 6 | V- — Charge-pump negative output |
| ピン 7 | R1OUT — Receiver 1 logic output |
| ピン 8 | R1IN — Receiver 1 RS-232 input |
| ピン 9 | T1OUT — Transmitter 1 RS-232 output |
| ピン 10 | T2IN — Transmitter 2 logic input |
| ピン 11 | R2OUT — Receiver 2 logic output |
| ピン 12 | R2IN — Receiver 2 RS-232 input |
| ピン 13 | T1IN — Transmitter 1 logic input |
| ピン 14 | GND — Device ground |
| ピン 15 | VCC — Positive supply input |
| ピン 16 | T2OUT — Transmitter 2 RS-232 output |
主な用途
MAX3232ECDW の用途: 6 件s: Industrial Serial Port Interface, Barcode Reader Connectivity, Test and Measurement Equipment, Security and Access Control, Point-of-Sale Terminal, Embedded Service Console.
Industrial Serial Port Interface
The MAX3232ECDW fits industrial serial adapters that connect a 3.3 V or 5 V controller to an RS-232 equipment port. Its two transmitters and two receivers support full-duplex serial communication, while the 3 V to 5.5 V supply range allows use with either common logic rail. The ±15 kV IEC pin-to-pin ESD protection strengthens the connector side of systems exposed to electrostatic discharge. Place the charge-pump capacitors and supply bypass capacitor according to the manufacturer datasheet, and route the connector-side traces as short as practical.
おすすめ
Barcode Reader Connectivity
The MAX3232ECDW provides a compact interface between a barcode scanner with an RS-232 port and a host controller operating from 3.3 V or 5 V. Two transmitters and receivers permit simultaneous transmit and receive channels when the scanner protocol requires bidirectional communication. Its 16-pin SOIC package preserves PCB area, and its ±15 kV IEC line-side ESD protection is useful in retail, warehouse, and logistics equipment where a scanner cable may be handled frequently.
おすすめ
Test and Measurement Equipment
The MAX3232ECDW is appropriate for test instruments and laboratory controllers that retain RS-232 service or communication ports. A single 3 V to 5.5 V supply simplifies interface implementation, and the integrated dual charge pump avoids requiring a separate negative rail. The two-channel driver and receiver arrangement supports common diagnostic protocols. Because external test leads and cables can carry electrostatic discharge, the family's ±15 kV IEC pin-to-pin protection provides a useful first layer of ruggedization, although separate surge and cable protection may still be required.
おすすめ
Security and Access Control
The MAX3232ECDW can connect RS-232 access-control readers, controllers, and alarm panels to a 3.3 V or 5 V embedded system. The dual-driver, dual-receiver arrangement supports typical request-and-response serial links without requiring a larger multi-channel transceiver. Its 16-pin SOIC package is practical for compact controller boards, while ±15 kV IEC protection on the serial connection pins improves resilience against electrostatic discharge encountered around door hardware and installed cabling.
おすすめ
Point-of-Sale Terminal
The MAX3232ECDW is useful in point-of-sale terminals, receipt printers, scales, and customer displays that use legacy RS-232 links. Operating from 3 V to 5.5 V allows it to share either the terminal's 3.3 V logic rail or a 5 V peripheral rail. Two transmitters and two receivers cover standard bidirectional serial communication, and the small SOIC footprint limits board consumption. The ±15 kV IEC protection rating should be considered when the peripheral cable connects to equipment that may be touched by users.
おすすめ
Embedded Service Console
The MAX3232ECDW can serve as the RS-232 interface for an embedded service console used during configuration, diagnostics, or firmware maintenance. The device's 3 V to 5.5 V operating range accommodates both 3.3 V and 5 V embedded processors, while the integrated dual charge pump simplifies the power architecture. Its two transmitters and two receivers support a full-duplex console connection. In unattended equipment, line-side ESD protection helps limit damage from service leads, but the connector should still include appropriately selected surge protection for the installation environment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX3232ECDW — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX3232EIDWR | MAX3232ECWE+ | MAX3232CDW | MAX3232CPWR | SP3232EBCN-L/TR |
|---|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | MaxLinear |
主な差別化要因
- Higher specified connector-side ESD protection than the MAX3232C alternatives (vs MAX3232CDW)
- Pin-compatible industrial-temperature sourcing option (vs MAX3232EIDWR)
- Second-source path with the same SOIC-16 footprint (vs SP3232EBCN-L/TR)
設計ノート
Place the C1 and C2 charge-pump capacitors directly across their designated pins with minimal loop area and short ground returns. Add the recommended supply bypass capacitor at VCC and route it to the ground reference in the same way. Component-placement changes can increase charge-pump ripple and reduce margin for reliable RS-232 signaling.
Keep the connector-side RIN and TOUT nets away from clocks, switching regulators, and high-current return paths. Maintain a continuous ground reference between the SOIC ground pin and the connector shield or signal ground. Use controlled-impedance routing if the cable or PCB interconnect is long, and avoid adding unnecessary stubs near the RS-232 pins.
Do not treat the integrated ±15 kV IEC ESD rating as a complete surge-protection solution. The protection is designed for electrostatic-discharge events on the specified pins, while lightning, switching transients, and long cable installations may require coordinated surge and overvoltage protection. Confirm that capacitor values, pin orientation, and the MAX3232E versus MAX3232C ESD requirement match the selected ordering code.
コンプライアンス情報
The manufacturer material identifies TIA/EIA-232-F compliance and ±15 kV IEC pin-to-pin ESD protection. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not established by the cited product summaries.