MAX3232EUE+T - Dual RS-232 Transceiver | Analog Devices
部品番号: MAX3232EUE+T ✓ 生産中MAX3232EUE+T 概要
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compliant voltage levels and restores RS-232 inputs to compatible logic levels. The MAX3232 belongs to the interface IC hierarchy, combining line drivers, line receivers, charge pumps, and protection functions in one device. Its charge-pump architecture supports true RS-232 operation from a single 3.0 V to 5.5 V supply without a separate negative supply rail.
The device requires only four external 0.1 µF charge-pump capacitors. Its integrated dual charge pump generates the positive and negative voltages needed by the drivers, while the receiver side converts incoming serial data into CMOS-compatible signals. The MAX3232E family provides low power consumption, including approximately 300 µA typical quiescent current reported for the MAX3232EUE+T, making it suitable for equipment where both interface performance and operating efficiency matter.
With two transmit and two receive channels, the transceiver can support two RS-232 ports or provide hardware flow-control signals alongside one primary data channel. Operation from 3.0 V to 5.5 V allows use with 3.3 V and 5 V logic systems. Its 16-pin TSSOP package supports compact surface-mount assemblies, while the stated data-rate capability of up to 1 Mbps suits higher-speed serial links, instrumentation, and industrial control equipment.
Typical applications include industrial serial consoles, point-of-sale terminals, test and measurement equipment, barcode scanners, and embedded systems communicating with legacy RS-232 peripherals. The device is especially useful when the logic supply is 3.3 V but the attached peripheral still requires true bipolar RS-232 signaling.
For a reliable layout, place all four 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog and high-speed digital traces. Confirm signal polarity, flow-control direction, and connector pin assignments during schematic review because the transmit and receive pins are dedicated rather than automatically interchangeable.
This page combines the manufacturer's electrical and package information with same-family drop-in alternatives, application guidance, interface-design notes, and a parameter comparison. It is intended to help engineers identify the correct MPN, validate PCB compatibility, and implement a reliable RS-232 interface.
ドロップイン代替品: MAX3232EUE+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX3232EUE+T (同一形状・フットプリント) — 相違点: Product Type, Package, Charge-Pump Architecture, Charge-Pump Capacitors, ESD Protection.
MAX3232ECUE+
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3232CUE+T
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3232EUE+T 仕様
| Device Type | 2/2 RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| Typical Quiescent Current | 300 µA |
| Charge-Pump Capacitor Value | 0.1 µF each |
| Required Charge-Pump Capacitors | 4 |
| Driver Transition Time | 300 ns |
| Package Type | 16-pin TSSOP |
| 実装タイプ | Surface mount |
| Logic Compatibility | CMOS-compatible |
| Charge-Pump Architecture | Dual |
MAX3232EUE+T 16-pin tssop ピン配置ガイド
MAX3232EUE+T (16-pin tssop パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX3232EUE+T.
詳細は データシート をご参照ください。
主な用途
MAX3232EUE+T の用途: 6 件s: 3.3 V Industrial Serial Console, Point-of-Sale Terminal Interface, Barcode Scanner Connectivity, Test and Measurement Equipment, Embedded Service and Configuration Port, Network Equipment Maintenance Port.
3.3 V Industrial Serial Console
The MAX3232EUE+T is suitable for a 3.3 V controller that must communicate with legacy equipment through a true RS-232 port. Its 3.0 V to 5.5 V operating range permits operation from a 3.3 V rail, while the dual charge-pump circuit generates the bipolar voltage levels required at the connector. The two-driver and two-receiver arrangement can support a data path plus hardware flow control. With a stated capability of up to 1 Mbps, the interface offers more performance headroom than required by many legacy consoles, although the peripheral's actual baud rate remains the limiting factor.
おすすめ
Point-of-Sale Terminal Interface
A point-of-sale terminal often combines a low-voltage embedded processor with a printer, scanner, or customer-facing peripheral that retains an RS-232 connector. The MAX3232EUE+T bridges that boundary by converting CMOS logic into true RS-232 levels and receiving commands from the peripheral. Its 16-pin TSSOP package supports compact controller-board placement, while four 0.1 µF external capacitors keep the charge-pump support network manageable. The 3.3 V to 5.5 V supply range also allows the same interface design to be adapted to different embedded-computer configurations.
おすすめ
Barcode Scanner Connectivity
The MAX3232EUE+T can connect an embedded host to a barcode scanner that uses an RS-232 interface. The two receivers allow command responses and hardware status to return to the host, while the two drivers provide the outbound command and flow-control paths. Operating from 3.0 V to 5.5 V supports compact scanners and industrial terminals with either 3.3 V or 5 V supply rails. Design the layout to keep the cable-side driver traces away from sensitive logic and provide the four charge-pump capacitors with short, symmetrical connections.
おすすめ
Test and Measurement Equipment
The MAX3232EUE+T is appropriate for test and measurement equipment that retains a service or control port using true RS-232 signaling. Its up-to-1-Mbps capability supports faster instrument-control traffic, and the integrated charge pump removes the need for a separate negative supply. The two transmit and two receive channels can be allocated according to the instrument protocol, including separate data and handshake lines. Because RS-232 is a single-ended interface susceptible to ground offsets and cable noise, the connector return path and chassis grounding should be designed carefully rather than treated as an ordinary logic signal.
おすすめ
Embedded Service and Configuration Port
The MAX3232EUE+T can provide a configuration and service port on an embedded controller board that must communicate with a laptop or service terminal using RS-232. Its low 3.0 V minimum supply allows operation from modern embedded rails, while the true RS-232 charge-pump output remains compatible with conventional PC serial-port equipment. Two channels support either two asynchronous links or one data link with hardware flow control. A robust implementation should include software handshaking, inversion checks, connector keying, and a defined grounding strategy for systems connected through long or unbalanced RS-232 cables.
おすすめ
Network Equipment Maintenance Port
The MAX3232EUE+T can implement a maintenance or out-of-band management connection in networking equipment where the main system architecture no longer includes a physical RS-232 connector. A low-power management controller can use the transceiver to communicate with a laptop during installation or troubleshooting. The 16-pin TSSOP package conserves board area, and the 3.0 V to 5.5 V range permits integration with mixed-voltage logic. Place the protection network near the connector and route the interface away from high-energy switching nodes to reduce the chance that transient or common-mode disturbances interfere with service access.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX3232EUE+T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX3232ECUE+ | MAX3232CUE+T |
|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Device Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver |
| Drivers / Receivers | 2 / 2 | 2 / 2 | 2 / 2 |
主な差別化要因
- Supports true RS-232 from a 3.0 V supply (vs MAX3232ECUE+)
- Compact 16-pin TSSOP implementation (vs MAX3232CUE+T)
- Low external charge-pump support count (vs MAX3232ECUE+)
設計ノート
Place the four required 0.1 µF charge-pump capacitors as close as practical to the MAX3232EUE+T charge-pump pins. Keep each capacitor's ground connection short and use the ground-plane reference shown by the manufacturer's layout guidance. Avoid placing the capacitors beneath the TSSOP body or behind a dense row of unrelated signals, because longer charge-pump current paths can increase transient disturbance and reduce operating margin.
Route the connector-side driver outputs as differential-like RS-232 signals even though the interface is single-ended, and keep them separated from clocks, ADC inputs, and sensitive sensor lines. Preserve the ground return associated with the RS-232 connector, but avoid allowing large switching currents to share narrow paths with the transceiver ground. A clear separation between logic-side and cable-side routing improves noise immunity.
Do not assign RS-232 pins solely from signal names because several MAX3232-family pins support driver or receiver functions. Check the manufacturer's pin table for the exact configuration, verify the external charge-pump capacitor connections, and confirm logic polarity and hardware-flow direction. After assembly, perform a local driver-to-receiver loopback test before connecting equipment with potentially different grounding or signal conventions.
The charge pump is an internal switching source and can couple energy into nearby circuitry even though the interface itself uses a low-noise bipolar output. Keep sensitive analog traces away from the charge-pump capacitor network and provide a solid ground plane beneath the device where practical. If the board combines RS-232 with RF, audio, or precision measurement, validate conducted and radiated emissions with the final enclosure and cable configuration.
コンプライアンス情報
The manufacturer product page identifies MAX3232 as a production device, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was exposed in the cited records. AEC-Q100 status is not applicable to this general-purpose RS-232 transceiver.