MAX3243EAI+G1Z - 250kbps RS-232 Transceiver | Analog Devices
部品番号: MAX3243EAI+G1Z ✓ 生産中MAX3243EAI+G1Z 概要
An RS-232 transceiver is the electrical interface between a digital UART or asynchronous communication controller and a serial connector. It converts low-voltage CMOS logic levels into RS-232-compatible levels and receives RS-232 signals for conversion back to logic levels. The MAX3243 belongs to the RS-232 interface IC, communications-interface, and power-management semiconductor hierarchy.
The MAX3243E family combines three drivers and five receivers in a single device, allowing several serial functions or an additional monitoring receiver to share one interface. Its ±15 kV ESD protection applies to the serial-port connection pins, while its 250 kbps capability supports data rates above the conventional 115.2 kbps rate commonly used by legacy UART equipment.
A dual charge-pump circuit supports the voltage conversion required by RS-232. The MAX3243E family also provides automatic shutdown and wake-up behavior, reducing supply current when no valid receiver signal is present. The MAX3243EAI+G1Z is identified as a 28-pin SSOP industrial-temperature ordering configuration, although detailed temperature and package dimensions should be confirmed against the ordering information in the manufacturer datasheet before release.
Typical uses include multiport serial adapters, industrial equipment interfaces, POS terminals, instrumentation, data-acquisition systems, and embedded controller links. The five receivers are especially useful when a system needs more incoming channels than the three outgoing driver channels, such as monitor, status, or handshake signals.
For a new PCB, place the charge-pump capacitors and interface bypass capacitors exactly as shown in the manufacturer’s recommended layout. Route TX and RX traces away from sensitive analog circuitry, keep the connector-side protection path short, and verify signal levels, ground references, and supply sequencing before production.
This page consolidates the manufacturer’s interface details, ordering information, application guidance, and available substitution research into a design-focused guide. It also identifies where an exact drop-in alternative is confirmed and where a proposed substitute requires careful pinout and protocol validation before use.
ドロップイン代替品: MAX3243EAI+G1Z — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX3243EAI+G1Z (同一形状・フットプリント) — 相違点: Maximum Data Rate, Power Management Feature, Product Type, Supply Voltage Range.
MAX3243EAI+
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3243EAI+G1Z 仕様
| Product Type | RS-232 line driver and receiver transceiver IC |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Transmit Drivers | 3 drivers |
| Number of Receive Channels | 5 receivers |
| ESD Protection | ±15 kV HBM |
| 電源電流 | 1 µA |
| Power Management Feature | AutoShutdown automatic shutdown and wake-up |
| Communication Standard | EIA/TIA-232-F |
| Interface Signaling | V.28/V.24 |
| Charge-Pump Circuit | Dual charge-pump circuit |
| ピン数 | 28 pins |
| パッケージ | 28-pin SSOP |
| 実装タイプ | Surface mount |
| ESD Protected Pins | Serial-port connection pins including GND |
MAX3243EAI+G1Z 28-pin ssop ピン配置ガイド
MAX3243EAI+G1Z (28-pin ssop パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX3243EAI+G1Z.
詳細は データシート をご参照ください。
主な用途
MAX3243EAI+G1Z の用途: 6 件s: Industrial serial data acquisition, Multiport RS-232 adapter, Point-of-sale terminal interface, Embedded controller RS-232 link, Test and measurement instrumentation, Portable equipment service port.
Industrial serial data acquisition
The MAX3243EAI+G1Z fits industrial data-acquisition equipment that must exchange asynchronous serial data with sensors, analyzers, or laboratory instruments. Its three transmit drivers support command and control traffic, while five receivers provide additional inputs for status, acknowledgment, or monitoring signals. The 250 kbps rate exceeds common 115.2 kbps UART operation, and the 3 V to 5.5 V supply range supports both 3.3 V and 5 V control systems. The ±15 kV HBM ESD protection strengthens the connector-side interface against industrial handling transients, while AutoShutdown can reduce current when connected equipment is idle.
おすすめ
Multiport RS-232 adapter
A multiport adapter can use the MAX3243EAI+G1Z when one connector or internal link must present multiple RS-232 functions. Three driver outputs are sufficient for transmit, receive-data, and handshake or control signaling, while the five receiver channels can monitor several incoming lines or support additional downstream ports. Its 250 kbps capability allows design teams to use faster UART modes where the connected equipment supports them. The 28-pin SSOP package conserves board area, and AutoShutdown behavior is valuable in portable or intermittently connected adapters where idle-system current must remain low.
おすすめ
Point-of-sale terminal interface
The MAX3243EAI+G1Z is appropriate for point-of-sale terminals that communicate with peripherals through legacy RS-232 links. Three driver channels can support outbound commands and handshake signals, while five receiver inputs allow the terminal to monitor multiple peripheral responses without adding separate receiver packages. Its 3 V to 5.5 V operating range simplifies integration with both legacy 5 V and modern 3.3 V logic systems. The ±15 kV HBM ESD protection adds useful margin at accessible connector pins, although the complete enclosure, grounding, and cable-shield design must still meet the product’s ESD and EMC requirements.
おすすめ
Embedded controller RS-232 link
The MAX3243EAI+G1Z provides a practical bridge between a UART-based embedded controller and an RS-232 device. Its dual charge-pump circuit performs the required level conversion, while three driver outputs can support data, request, and flow-control signals. A fifth receiver channel offers additional readback or monitoring capability beyond the minimum data and handshake paths. At a maximum 250 kbps, the device supports conventional serial ports and higher-rate short-distance links. The SSOP footprint and 3 V minimum supply are useful in compact controller boards where board area and mixed-voltage power design are important constraints.
おすすめ
Test and measurement instrumentation
The MAX3243EAI+G1Z suits bench instruments and portable test equipment that use RS-232 for remote commands, calibration data, or instrument-status reporting. Three drivers handle command, measurement, and handshake outputs, and five receivers can accept responses from several instruments or status lines from one link. The 250 kbps rate supports fast transfer of moderate command and result blocks. AutoShutdown helps portable instruments conserve power when the remote link is inactive, while the 28-pin SSOP package leaves room for analog, display, and measurement circuitry on crowded instrument boards.
おすすめ
Portable equipment service port
The MAX3243EAI+G1Z can support a service or configuration port in portable electronics that need a wired RS-232 interface during installation or maintenance. Its three drivers and five receivers permit a richer control interface than a basic two-channel UART bridge, including request, acknowledgment, and status signals. Operation from 3 V to 5.5 V allows use with rechargeable-system rails and legacy service interfaces. When the connected host is inactive, AutoShutdown reduces supply consumption, which is especially helpful in battery-operated equipment. Firmware should use deterministic line-state logic to avoid interpreting disconnected or floating RS-232 inputs as valid commands.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX3243EAI+G1Z — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX3243EAI+ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP |
| Product Type | 3-driver/5-receiver RS-232 transceiver | 3-driver/5-receiver RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV HBM | ±15 kV HBM |
| AutoShutdown Supply Current | 1 µA | 1 µA |
| Transmitter Channels | 3 | 3 |
| Receiver Channels | 5 | 5 |
| Compliance Standard | EIA/TIA-232-F | EIA/TIA-232-F |
主な差別化要因
- Five receiver inputs in a compact RS-232 interface (vs MAX3237EAI+)
- Faster supported serial data rate (vs MAX3237EAI+)
- Closest same-family ordering option (vs MAX3243EEUI+T)
設計ノート
Use the manufacturer’s recommended layout for the charge-pump capacitors and place those components close to their designated pins. Keep the high-voltage driver and receiver paths away from low-level logic and analog traces. The external RS-232 connector, protection network, and transceiver should be positioned so connector-side surge current follows a short, direct return path rather than passing through sensitive circuitry.
Decouple the 3 V to 5.5 V supply with the capacitance and placement specified in the manufacturer application circuit. The charge-pump circuit generates the bipolar voltages required by RS-232, so unstable supply voltage or poorly decoupled pump nodes can increase jitter or interfere with data transmission. Confirm startup, logic-level thresholds, and receiver output states when the supply crosses the 3 V operating boundary.
Do not treat an RS-232 receiver output as a valid command unless the interface firmware confirms a valid mark, bias, or line state. AutoShutdown can wake the receivers when a connected or floating line appears active, so robust state-machine design and appropriate connector termination are important. Also verify that every replacement retains the same channel count, shutdown behavior, logic levels, and SSOP pin assignments.
RS-232 driver outputs carry high-voltage, fast-edge transitions that can couple into nearby circuitry. Maintain the recommended spacing between TX and RX routes, return connector shields to the chassis or designated ground strategy, and avoid routing unprotected outputs around sensitive analog inputs. Validate conducted and radiated emissions on the final assembly because cable length, grounding, and enclosure construction can materially affect system-level EMI performance.
コンプライアンス情報
The component is described as an RS-232 communications interface meeting EIA/TIA-232-F. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the cited product and distributor information.