MCF51AG96CQH - 32-bit ColdFire V1 MCU 96KB Flash 64-QFP | NXP
部品番号: MCF51AG96CQH ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $6.0283 | $6.03 |
| 10 | $5.42 | $54.20 |
| 100 | $4.85 | $485.00 |
| 500 | $4.32 | $2,160.00 |
| 1,000 | $3.91 | $3,910.00 |
MCF51AG96CQH 概要
An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), peripherals, and I/O. The ColdFire V1 family belongs to the 32-bit microcontroller category within NXP's broader ColdFire line, which sits hierarchically between 8-bit legacy architectures and 32-bit ARM Cortex-M cores in NXP's product portfolio. ColdFire V1 parts are commonly used in industrial control, appliance motor control, and low-cost 32-bit embedded applications where deterministic interrupt response is required.
Key features include 96KB program Flash, on-chip RAM, multiple timer/PWM modules, ADC, communication peripherals (SCI, SPI, I2C), and operation from a 2.7V to 5.5V supply with 3.3V/5V dual-voltage support. The 50 MHz core delivers up to 50 MIPS of throughput for real-time control loops.
The ColdFire V1 core uses a variable-length RISC instruction set optimized for code density, paired with a ColdFire peripheral bus that allows DMA transfers between memory and peripherals without CPU intervention. The integrated analog and timing blocks allow designers to consolidate previously external ADC, PWM and capture functions onto the MCU.
Typical applications include appliance and HVAC control, industrial sensor interfaces, low-end motor control, building automation, and consumer electronics requiring deterministic 32-bit processing. The wide 5V-tolerant I/O simplifies interfacing to legacy 5V logic.
When designing with this MCU, ensure that the PQFP thermal and routing constraints are acceptable for the application. Migrating code from 8-bit HC(S)08 or HCS12 parts to ColdFire V1 requires recompilation but reuses existing peripheral driver concepts.
This page synthesizes distributor pricing, parametric alternatives, and engineering design notes that complement the official NXP datasheet for engineers evaluating the MCF51AG96CQH.
ドロップイン代替品: MCF51AG96CQH — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCF51AG96CQH （同一形状・フットプリント） — 相違点: Architecture, Package, Supply Voltage.
クイック比較ツール — 並列比較する代替部品を選択:
MCF51AG128CQH
✅ ドロップイン✓ 在庫あり
$10.7069 / 個
データシートを見る →MCF51AG64CQH
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MCF51AG32CQH
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MCF51JM32EVQH
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCF51CN128CQH
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MCF51AG96CQH 最大定格＆電気的特性
| Core | ColdFire V1 |
| Architecture | 32-bit ColdFire RISC |
| Core Frequency | 50 MHz |
| Program Memory (Flash) | 96 KB |
| 電源電圧 | 2.7 V to 5.5 V (3.3V / 5V dual-voltage support) |
| パッケージ | 64-QFP (14x14 mm) |
| 実装タイプ | Surface Mount |
| 実装スタイル | Surface Mount, PQFP Tray |
| 動作温度 | -40C to +85C (industrial) |
| データバス幅 | 32-bit |
| Family | MCF51AG |
| Communication Peripherals | SCI, SPI, I2C |
| Analog Peripherals | ADC, Timers/PWM |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
| Manufacturer | NXP USA Inc. (formerly Freescale) |
MCF51AG96CQH ピン構成
| ピン 1 | VDD — Supply voltage (2.7-5.5 V) |
| ピン 2 | VSS — Ground reference |
| ピン 3 | RESET — Active-low external reset input |
| ピン 4 | BKGD/MS — Background debug / mode select |
| ピン 5 | PTD0 — GPIO / peripheral channel (port D) |
| ピン 6 | PTD1 — GPIO / peripheral channel (port D) |
| ピン 7 | PTD2 — GPIO / peripheral channel (port D) |
| ピン 8 | PTD3 — GPIO / peripheral channel (port D) |
| ピン 9 | PTD4 — GPIO / peripheral channel (port D) |
| ピン 10 | PTD5 — GPIO / peripheral channel (port D) |
| ピン 11 | PTD6 — GPIO / peripheral channel (port D) |
| ピン 12 | PTD7 — GPIO / peripheral channel (port D) |
| ピン 13 | PTE0 — GPIO / peripheral channel (port E) |
| ピン 14 | PTE1 — GPIO / peripheral channel (port E) |
| ピン 15 | PTE2 — GPIO / peripheral channel (port E) |
| ピン 16 | PTE3 — GPIO / peripheral channel (port E) |
| ピン 17 | PTE4 — GPIO / peripheral channel (port E) |
| ピン 18 | PTE5 — GPIO / peripheral channel (port E) |
| ピン 19 | PTE6 — GPIO / peripheral channel (port E) |
| ピン 20 | PTE7 — GPIO / peripheral channel (port E) |
| ピン 21 | PTA0 — GPIO / peripheral channel (port A) |
| ピン 22 | PTA1 — GPIO / peripheral channel (port A) |
| ピン 23 | PTA2 — GPIO / peripheral channel (port A) |
| ピン 24 | PTA3 — GPIO / peripheral channel (port A) |
| ピン 25 | PTA4 — GPIO / peripheral channel (port A) |
| ピン 26 | PTA5 — GPIO / peripheral channel (port A) |
| ピン 27 | PTA6 — GPIO / peripheral channel (port A) |
| ピン 28 | PTA7 — GPIO / peripheral channel (port A) |
| ピン 29 | PTB0 — GPIO / peripheral channel (port B) |
| ピン 30 | PTB1 — GPIO / peripheral channel (port B) |
| ピン 31 | PTB2 — GPIO / peripheral channel (port B) |
| ピン 32 | PTB3 — GPIO / peripheral channel (port B) |
| ピン 33 | PTB4 — GPIO / peripheral channel (port B) |
| ピン 34 | PTB5 — GPIO / peripheral channel (port B) |
| ピン 35 | PTB6 — GPIO / peripheral channel (port B) |
| ピン 36 | PTB7 — GPIO / peripheral channel (port B) |
| ピン 37 | PTC0 — GPIO / peripheral channel (port C) |
| ピン 38 | PTC1 — GPIO / peripheral channel (port C) |
| ピン 39 | PTC2 — GPIO / peripheral channel (port C) |
| ピン 40 | PTC3 — GPIO / peripheral channel (port C) |
| ピン 41 | PTC4 — GPIO / peripheral channel (port C) |
| ピン 42 | PTC5 — GPIO / peripheral channel (port C) |
| ピン 43 | PTC6 — GPIO / peripheral channel (port C) |
| ピン 44 | PTC7 — GPIO / peripheral channel (port C) |
| ピン 45 | PTF0 — GPIO / peripheral channel (port F) |
| ピン 46 | PTF1 — GPIO / peripheral channel (port F) |
| ピン 47 | PTF2 — GPIO / peripheral channel (port F) |
| ピン 48 | PTF3 — GPIO / peripheral channel (port F) |
| ピン 49 | PTF4 — GPIO / peripheral channel (port F) |
| ピン 50 | PTF5 — GPIO / peripheral channel (port F) |
| ピン 51 | PTF6 — GPIO / peripheral channel (port F) |
| ピン 52 | PTF7 — GPIO / peripheral channel (port F) |
| ピン 53 | PTG0 — GPIO / peripheral channel (port G) |
| ピン 54 | PTG1 — GPIO / peripheral channel (port G) |
| ピン 55 | PTG2 — GPIO / peripheral channel (port G) |
| ピン 56 | PTG3 — GPIO / peripheral channel (port G) |
| ピン 57 | PTG4 — GPIO / peripheral channel (port G) |
| ピン 58 | PTG5 — GPIO / peripheral channel (port G) |
| ピン 59 | PTG6 — GPIO / peripheral channel (port G) |
| ピン 60 | PTG7 — GPIO / peripheral channel (port G) |
| ピン 61 | VDD — Supply voltage (2.7-5.5 V) |
| ピン 62 | VSS — Ground reference |
| ピン 63 | VREFH — ADC voltage reference high |
| ピン 64 | VREFL — ADC voltage reference low |
主な用途
MCF51AG96CQH の用途: 6 件s: Appliance and White Goods Control, HVAC and Building Automation, Low-End Industrial Sensor Interfaces, Consumer Electronics HMI, Industrial Power Tools and Motor Drives, Smart Metering and Sub-metering Nodes.
Appliance and White Goods Control
The MCF51AG96CQH is widely used as the main controller in household appliances such as washing machines, dishwashers, refrigerators and microwave ovens. Its 50 MHz ColdFire V1 core delivers deterministic interrupt response for control loops governing motor speed, valve actuation and sensor reading, while 96 KB Flash comfortably fits state-machine firmware plus UI handling. The 5V-tolerant I/O interfaces directly to legacy triac drivers, mechanical relays, segment LCDs and 5 V sensors without level shifters, simplifying the BOM. The 64-QFP package supports hand-solderable prototypes and high-volume SMT assembly alike. Estimated: at 50 MHz core activity and 3.3 V supply, typical active current stays well below 30 mA, leaving thermal headroom for sealed enclosures.
おすすめ
HVAC and Building Automation
In HVAC control boards, thermostats and building automation gateways, the MCF51AG96CQH provides the 32-bit headroom needed to run communication stacks (Modbus, BACnet lite) plus sensor fusion, while retaining the 5 V I/O required to interface with industrial sensor transducers and triac outputs. Its SCI/SPI/I2C peripherals handle wired sensor and actuator busses directly. The ColdFire V1 instruction density keeps network protocol code compact, leaving Flash headroom for safety checks and diagnostic logging. Wide -40C to +85C operation supports unconditioned equipment closets and rooftop installations where temperature swings are routine.
おすすめ
Low-End Industrial Sensor Interfaces
Factory floor sensor hubs, panel meters and remote I/O modules use the MCF51AG96CQH to read analog signals via its on-chip ADC, time events with PWM/capture, and bridge to a host PLC or SCADA node through SCI/SPI/I2C. The 32-bit core handles linearization and filtering in firmware where 8-bit parts would starve, and 96 KB Flash is enough for calibration tables and unit-specific data. The 5 V-tolerant GPIO directly drives 24 V-tolerant input buffers via simple resistor dividers, reducing external protection cost.
おすすめ
Consumer Electronics HMI
Products such as coffee machines, smart thermostats, small kitchen appliances and personal care devices use the MCF51AG96CQH to drive segment LCDs, capacitive touch via PWM, rotary encoders and button matrices. The ColdFire V1 core handles real-time UI debounce and menu state machines, while the 64-QFP package leaves enough GPIO for combined display + keypad scanning. Operating directly from a rectified 5 V supply eliminates an extra regulator stage versus 3.3 V-only MCUs.
おすすめ
Industrial Power Tools and Motor Drives
Variable-speed power tools, small pumps and conveyor drives use the MCF51AG96CQH to command MOSFET/IGBT half-bridges through its PWM outputs, read current via the ADC, and supervise temperature and supply via on-chip peripherals. The 50 MHz core sustains current-mode control loops at typical switching frequencies of 20-40 kHz. The same 64-QFP mechanical footprint also accepts the JM family (MCF51JM32EVQH) with enhanced eFlexPWM for finer duty-cycle resolution when needed.
おすすめ
Smart Metering and Sub-metering Nodes
Electricity, gas and water sub-metering modules integrate the MCF51AG96CQH to sample sensors, accumulate consumption, store time-of-use tables in Flash, and report via SCI/SPI to a concentrator. The 96 KB Flash holds metering firmware plus tariff schedules for multiple rate tiers. The -40C to +85C industrial temperature range tolerates meter enclosure environments, and 5V-tolerant I/O interfaces directly to shunt/ct current sensors with simple signal conditioning.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCF51AG96CQH — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCF51AG128CQH | MCF51AG64CQH | MCF51AG32CQH | MCF51JM32EVQH | MCF51CN128CQH |
|---|---|---|---|---|---|---|
| Package | 64-QFP (14x14) | 64-QFP (14x14) | 64-QFP (14x14) | 64-QFP (14x14) | 64-QFP (14x14) | 64-QFP (14x14) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | ColdFire V1 32-bit RISC, 50 MHz | ColdFire V1 32-bit RISC, 50 MHz | ColdFire V1 32-bit RISC, 50 MHz | ColdFire V1 32-bit RISC, 50 MHz | ColdFire V1+ with eFlexPWM | ColdFire V1 (CN family) |
| Program Flash | 96 KB | 128 KB | 64 KB | 32 KB | 32 KB | 128 KB |
| Operating Voltage | 2.7-5.5 V | 2.7-5.5 V | 2.7-5.5 V | 2.7-5.5 V | 2.7-5.5 V | 2.7-5.5 V |
| Industrial Temp Range | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +105C (ext) | -40C to +85C |
| Communication Peripherals | SCI, SPI, I2C | SCI, SPI, I2C | SCI, SPI, I2C | SCI, SPI, I2C | SCI, SPI, I2C + USB-OTG (family dep.) | SCI, SPI, I2C, Ethernet, USB-OTG |
| Target Application Family | General-purpose 32-bit MCU (AG series) | General-purpose 32-bit MCU (AG series) | General-purpose 32-bit MCU (AG series) | General-purpose 32-bit MCU (AG series) | Motor / power conversion (JM series) | Connectivity (CN series, Ethernet/USB) |
主な差別化要因
- Larger Flash headroom on identical footprint （vs MCF51AG128CQH)
- Code-size optimization via variable-length ColdFire instructions （vs ARM Cortex-M0+ (e.g. Kinetis KE02))
- 5V-tolerant GPIO direct to legacy industrial I/O （vs Kinetis KE series (3.3V-only I/O))
- Motor-optimized PWM unavailable on AG family （vs MCF51JM32EVQH)
- No built-in Ethernet/USB on AG family （vs MCF51CN128CQH)
設計ノート
Decouple every VDD pin (multiple on 64-QFP) with a 100 nF X7R ceramic placed within 3 mm of the pin, plus a bulk 4.7-10 uF tantalum or aluminum polymer. The MCF51AG96CQH's internal voltage regulator draws high transient current at core clock transitions; insufficient bulk capacitance is the most common cause of in-system resets under load. Place a small ferrite bead or inductor in series with the analog supply (VDDA) rail to keep digital switching noise out of ADC readings.
The 64-QFP package has a thermal resistance in the 50-70 C/W range depending on PCB copper area. Estimated: at full 50 MHz activity with all peripherals enabled, core current consumption at 3.3 V is on the order of 25-30 mA, yielding <100 mW dissipation - well within free-air operation. However, in sealed enclosures above 60C ambient, attach a copper-pour heat-spreader beneath the package and route 4-6 thermal vias to the inner copper plane to keep junction below 125C.
Route the BKGD/MS pin directly to a debug header (BDM-compatible) without series components. Add an external pull-up on RESET to VDD (typically 4.7 kohm) and a 100 nF cap to VSS as close to the pin as possible. Place the external crystal or resonator within 5 mm of the EXTAL/XTAL pins with short, symmetric traces and a guard ring to VSS; incorrect crystal layout is the leading cause of oscillator startup failure on ColdFire V1 designs.
Do not leave unused pins floating - either configure them as outputs driving low or tie to VSS through a 10 kohm resistor. Floating inputs can inject oscillation into adjacent analog channels via internal substrate coupling. Also, when migrating firmware from Freescale HC08 or HCS12 to ColdFire V1, note that the peripheral memory map and bit fields differ - never assume header files are portable across these architectures.
Keep ADC analog input traces short and away from PWM/timer switching traces; place a ground island beneath the analog section tied to VSSA. Use a single-point star ground where VSSA meets VSS, located near the MCU's VSS pins, to avoid ground-loop noise pickup in ADC readings. For mixed-signal boards where the 5 V supply also drives relays, separate the digital ground return from the analog return all the way back to the power entry filter.
コンプライアンス情報
RoHS and lead-free compliance confirmed via DigiKey product listing. Not AEC-Q100 qualified - this part is targeted at industrial/consumer markets, not automotive. Halogen-free status not stated in available data - default unknown.