MCF52230CAF60 - 60MHz 32-bit MCU with Ethernet | NXP
部品番号: MCF52230CAF60 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MCF52230CAF60 概要
A microcontroller is a programmable system-on-chip that combines a processor core, memory, peripherals, and I/O in one integrated component. The MCF52230 belongs to the ColdFire embedded-processor hierarchy and targets industrial networking, communications, automation, and control systems. Its Ethernet integration can reduce system complexity by combining protocol processing and physical-layer connectivity on the same device.
Verified source information identifies the device as part of the MCF5223x family and specifies its 60 MHz ColdFire V2 core, 128 KB flash, 43 I/O, 10/100 Fast Ethernet controller, and Ethernet physical layer. The available NXP overview also describes the family as compact embedded controllers combining 32-bit control with Ethernet connectivity. Detailed RAM, voltage, temperature, timer, serial-interface, and package-pin information was not included in the supplied source data and is therefore not inferred here.
The 80-LQFP package provides 80 external leads for power, ground, digital I/O, Ethernet, clock, and control functions. Its 14 x 14 mm outline supports compact embedded boards, but the relatively fine lead pitch requires careful PCB layout, clean ground distribution, and assembly-process control. Ethernet applications also need a suitably designed clock, magnetics, signal routing, power network, and physical-layer implementation.
Typical uses include embedded Ethernet controllers, industrial automation equipment, communications equipment, network-connected sensors, and compact control systems. The MCU's 60 MHz processing rate provides computational headroom for protocol handling and real-time control, while integrated Ethernet avoids a separate host interface in many designs. Actual firmware performance and interface availability should still be verified against the complete manufacturer datasheet and errata.
For a new design, confirm the exact peripheral set, electrical limits, memory map, pin multiplexing, and package tolerances in the NXP documentation before committing the PCB. For an existing design, validate clock configuration, Ethernet PHY implementation, startup behavior, and software initialization before substituting any device. This page distinguishes verified headline facts from unavailable detailed parameters rather than filling gaps with assumptions.
ドロップイン代替品: MCF52230CAF60 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCF52230CAF60 （同一形状・フットプリント） — 相違点: Package, Mounting Type, Core Architecture, Ethernet, Flash Memory.
クイック比較ツール — 並列比較する代替部品を選択:
MCF52231CAL60
✅ ドロップイン✓ 在庫あり
$9.85 / 個
データシートを見る →MCF52233CAF60
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →MCF52230CAF60 最大定格＆電気的特性
| Product Type | 32-bit microcontroller |
| Processor Core | ColdFire V2 |
| 最大クロック周波数 | 60 MHz |
| Flash Memory | 128 KB |
| Flash Organization | 128 KB (128K x 8) |
| Ethernet Controller | 10/100 Fast Ethernet FEC |
| Ethernet Physical Layer | Integrated EPHY |
| I/O Count | 43 I/O |
| パッケージ | 80-LQFP |
| Package Dimensions | 14 x 14 mm |
| 実装タイプ | Surface-mount LQFP |
| Core Architecture | 32-bit ColdFire |
| Application Classification | Embedded Ethernet controller |
| Manufacturer Lifecycle Status | NRND |
MCF52230CAF60 14 x 14 mm ピン配置ガイド
MCF52230CAF60 (14 x 14 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MCF52230CAF60.
詳細は データシート をご参照ください。
主な用途
MCF52230CAF60 の用途: 6 件s: Industrial Ethernet Controller, Industrial Automation Equipment, Networked Sensor Gateway, Communications Equipment, Compact Embedded Control System, Networked Monitoring System.
Industrial Ethernet Controller
MCF52230CAF60 fits an embedded Ethernet controller because it combines a 32-bit ColdFire V2 core running at 60 MHz with a 10/100 Fast Ethernet controller and integrated Ethernet physical layer. The MCU can manage protocol and supervisory tasks while its 43 I/O handle digital control signals. Designers should still validate pin multiplexing, PHY support, magnetics, termination, clocking, and the exact peripheral resources against the NXP datasheet before layout release.
おすすめ
Industrial Automation Equipment
The 60 MHz ColdFire V2 core provides a performance-oriented control platform for automation equipment, while 43 I/O offer a substantial digital interface for sensors, actuators, status indicators, and interlocks. Integrated Ethernet can connect the controller to supervisory systems without requiring a separate network processor. The design must still account for the target voltage, isolation, grounding, surge protection, environmental range, and real-time timing requirements, none of which are specified in the supplied data.
おすすめ
Networked Sensor Gateway
For a networked sensor gateway, MCF52230CAF60 combines Ethernet connectivity with 128 KB flash and 43 I/O, allowing sensor inputs, local status, and configuration data to be handled in one compact controller. Its 60 MHz core can support network and control tasks, but firmware partitioning and memory headroom must be evaluated. The supplied information does not confirm RAM capacity, ADC resources, operating voltage, or temperature limits, so those requirements need separate verification.
おすすめ
Communications Equipment
MCF52230CAF60 is suitable for compact communications equipment requiring a 32-bit control processor and integrated 10/100 Ethernet. The ColdFire V2 core at 60 MHz can coordinate protocol handling and equipment-control tasks, while the 43 I/O support external interfaces and status signaling. Firmware developers should confirm interrupt behavior, DMA and peripheral availability, and Ethernet timing because those details are not included in the provided search snippets.
おすすめ
Compact Embedded Control System
The 80-LQFP package and integrated Ethernet make MCF52230CAF60 relevant to compact embedded systems that need networked control without a separate communication device. Its 128 KB flash provides a defined code-storage resource, and 43 I/O support a broad external peripheral footprint. Before selecting it, confirm that 128 KB is sufficient for the application and validate package dimensions, pin mapping, clock source, reset behavior, and power requirements.
おすすめ
Networked Monitoring System
A monitoring system can use MCF52230CAF60 for local control and Ethernet reporting, with the integrated 10/100 Fast Ethernet controller and physical layer reducing the number of external network components. The 60 MHz ColdFire V2 core supports responsive supervisory logic, while 43 I/O can connect status and control lines. The supplied data does not establish analog-input capability, memory availability beyond flash, or environmental ratings, so those limits must be checked before selecting the MCU.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCF52230CAF60 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCF52231CAL60 | MCF52233CAF60 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
主な差別化要因
- Integrated Ethernet physical layer （vs MCF52231CAL60)
- Known core and memory configuration （vs MCF52233CAF60)
- Documented package configuration （vs MCF52231CAL60)
設計ノート
Use the manufacturer package drawing to define the 80-LQFP footprint, pin numbering, solder-mask clearance, and assembly allowances. The supplied data confirms an 80-LQFP 14 x 14 mm package but does not provide the exact lead pitch or pin table, so do not infer copper geometry from the package name alone. Cross-check the PCB library against the current NXP mechanical drawing before fabrication.
Design the Ethernet system around the exact power-supply and I/O voltage requirements from the NXP datasheet. The supplied data does not state operating voltage, current limits, or regulator recommendations. Validate the power rails, decoupling network, startup sequence, and Ethernet transceiver requirements against verified electrical characteristics rather than assuming compatibility with a 3.3 V or 5 V design.
Place the MCU and supporting network components with short, controlled return paths, especially around the Ethernet physical interface and clock circuitry. Keep sensitive Ethernet and power connections away from noisy switching nodes where possible. Because the supplied material does not provide a reference layout or pinout, validate the physical-layer implementation with NXP guidance and SI measurements before production.
Do not treat MCF52231CAL60 or MCF52233CAF60 as drop-in replacements merely because they appear in MCF5223x comparison searches. Verify pin assignment, memory size, Ethernet implementation, voltage, timing, package, and software compatibility. Also account for the NRND status of MCF52230CAF60 and obtain a lifecycle or product-change assessment before starting a long-life production design.
コンプライアンス情報
The supplied search data does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. NRND is a lifecycle designation, not a compliance qualification.
