MCF52230CAF60 - 60MHz 32-bit MCU with Ethernet | NXP
MPN： MCF52230CAF60 ✗ 停產MCF52230CAF60 概覽
A microcontroller is a programmable system-on-chip that combines a processor core, memory, peripherals, and I/O in one integrated component. The MCF52230 belongs to the ColdFire embedded-processor hierarchy and targets industrial networking, communications, automation, and control systems. Its Ethernet integration can reduce system complexity by combining protocol processing and physical-layer connectivity on the same device.
Verified source information identifies the device as part of the MCF5223x family and specifies its 60 MHz ColdFire V2 core, 128 KB flash, 43 I/O, 10/100 Fast Ethernet controller, and Ethernet physical layer. The available NXP overview also describes the family as compact embedded controllers combining 32-bit control with Ethernet connectivity. Detailed RAM, voltage, temperature, timer, serial-interface, and package-pin information was not included in the supplied source data and is therefore not inferred here.
The 80-LQFP package provides 80 external leads for power, ground, digital I/O, Ethernet, clock, and control functions. Its 14 x 14 mm outline supports compact embedded boards, but the relatively fine lead pitch requires careful PCB layout, clean ground distribution, and assembly-process control. Ethernet applications also need a suitably designed clock, magnetics, signal routing, power network, and physical-layer implementation.
Typical uses include embedded Ethernet controllers, industrial automation equipment, communications equipment, network-connected sensors, and compact control systems. The MCU's 60 MHz processing rate provides computational headroom for protocol handling and real-time control, while integrated Ethernet avoids a separate host interface in many designs. Actual firmware performance and interface availability should still be verified against the complete manufacturer datasheet and errata.
For a new design, confirm the exact peripheral set, electrical limits, memory map, pin multiplexing, and package tolerances in the NXP documentation before committing the PCB. For an existing design, validate clock configuration, Ethernet PHY implementation, startup behavior, and software initialization before substituting any device. This page distinguishes verified headline facts from unavailable detailed parameters rather than filling gaps with assumptions.
直接替換替代品，適用於 MCF52230CAF60 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MCF52230CAF60 （相同外形與佔位） — 差異在於 Package, Flash Memory, Maximum Clock Frequency, Core, Lifecycle Status.
MCF52231CAL60
✅ 直接替換聯絡詢價
查看資料表 →MCF52233CAF60
✅ 直接替換聯絡詢價
查看資料表 →MCF52230CAF60 最大額定值與電氣特性
| Product Type | 32-bit microcontroller |
| Processor Core | ColdFire V2 |
| 最大時脈頻率 | 60 MHz |
| Flash Memory | 128 KB |
| Flash Organization | 128 KB (128K x 8) |
| Ethernet Controller | 10/100 Fast Ethernet FEC |
| Ethernet Physical Layer | Integrated EPHY |
| I/O Count | 43 I/O |
| 封裝 | 80-LQFP |
| Package Dimensions | 14 x 14 mm |
| 安裝類型 | Surface-mount LQFP |
| Core Architecture | 32-bit ColdFire |
| Application Classification | Embedded Ethernet controller |
| Manufacturer Lifecycle Status | NRND |
MCF52230CAF60 14 x 14 mm 腳位配置指南
MCF52230CAF60（14 x 14 mm 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MCF52230CAF60.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCF52230CAF60 適用於 6 應用s: Industrial Ethernet Controller, Industrial Automation Equipment, Networked Sensor Gateway, Communications Equipment, Compact Embedded Control System, Networked Monitoring System.
Industrial Ethernet Controller
MCF52230CAF60 fits an embedded Ethernet controller because it combines a 32-bit ColdFire V2 core running at 60 MHz with a 10/100 Fast Ethernet controller and integrated Ethernet physical layer. The MCU can manage protocol and supervisory tasks while its 43 I/O handle digital control signals. Designers should still validate pin multiplexing, PHY support, magnetics, termination, clocking, and the exact peripheral resources against the NXP datasheet before layout release.
推薦
Industrial Automation Equipment
The 60 MHz ColdFire V2 core provides a performance-oriented control platform for automation equipment, while 43 I/O offer a substantial digital interface for sensors, actuators, status indicators, and interlocks. Integrated Ethernet can connect the controller to supervisory systems without requiring a separate network processor. The design must still account for the target voltage, isolation, grounding, surge protection, environmental range, and real-time timing requirements, none of which are specified in the supplied data.
推薦
Networked Sensor Gateway
For a networked sensor gateway, MCF52230CAF60 combines Ethernet connectivity with 128 KB flash and 43 I/O, allowing sensor inputs, local status, and configuration data to be handled in one compact controller. Its 60 MHz core can support network and control tasks, but firmware partitioning and memory headroom must be evaluated. The supplied information does not confirm RAM capacity, ADC resources, operating voltage, or temperature limits, so those requirements need separate verification.
推薦
Communications Equipment
MCF52230CAF60 is suitable for compact communications equipment requiring a 32-bit control processor and integrated 10/100 Ethernet. The ColdFire V2 core at 60 MHz can coordinate protocol handling and equipment-control tasks, while the 43 I/O support external interfaces and status signaling. Firmware developers should confirm interrupt behavior, DMA and peripheral availability, and Ethernet timing because those details are not included in the provided search snippets.
推薦
Compact Embedded Control System
The 80-LQFP package and integrated Ethernet make MCF52230CAF60 relevant to compact embedded systems that need networked control without a separate communication device. Its 128 KB flash provides a defined code-storage resource, and 43 I/O support a broad external peripheral footprint. Before selecting it, confirm that 128 KB is sufficient for the application and validate package dimensions, pin mapping, clock source, reset behavior, and power requirements.
推薦
Networked Monitoring System
A monitoring system can use MCF52230CAF60 for local control and Ethernet reporting, with the integrated 10/100 Fast Ethernet controller and physical layer reducing the number of external network components. The 60 MHz ColdFire V2 core supports responsive supervisory logic, while 43 I/O can connect status and control lines. The supplied data does not establish analog-input capability, memory availability beyond flash, or environmental ratings, so those limits must be checked before selecting the MCU.
推薦
推薦產品摘要
工程參考資料，適用於 MCF52230CAF60 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCF52231CAL60 | MCF52233CAF60 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
主要差異化特點
- Integrated Ethernet physical layer (對比MCF52231CAL60)
- Known core and memory configuration (對比MCF52233CAF60)
- Documented package configuration (對比MCF52231CAL60)
設計說明
Use the manufacturer package drawing to define the 80-LQFP footprint, pin numbering, solder-mask clearance, and assembly allowances. The supplied data confirms an 80-LQFP 14 x 14 mm package but does not provide the exact lead pitch or pin table, so do not infer copper geometry from the package name alone. Cross-check the PCB library against the current NXP mechanical drawing before fabrication.
Design the Ethernet system around the exact power-supply and I/O voltage requirements from the NXP datasheet. The supplied data does not state operating voltage, current limits, or regulator recommendations. Validate the power rails, decoupling network, startup sequence, and Ethernet transceiver requirements against verified electrical characteristics rather than assuming compatibility with a 3.3 V or 5 V design.
Place the MCU and supporting network components with short, controlled return paths, especially around the Ethernet physical interface and clock circuitry. Keep sensitive Ethernet and power connections away from noisy switching nodes where possible. Because the supplied material does not provide a reference layout or pinout, validate the physical-layer implementation with NXP guidance and SI measurements before production.
Do not treat MCF52231CAL60 or MCF52233CAF60 as drop-in replacements merely because they appear in MCF5223x comparison searches. Verify pin assignment, memory size, Ethernet implementation, voltage, timing, package, and software compatibility. Also account for the NRND status of MCF52230CAF60 and obtain a lifecycle or product-change assessment before starting a long-life production design.
合規資訊
The supplied search data does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. NRND is a lifecycle designation, not a compliance qualification.
