MCP3426A4-E/SN - 16-Bit Dual-Channel I2C ADC | Microchip
部品番号: MCP3426A4-E/SN ✓ 生産中MCP3426A4-E/SN 概要
A sigma-delta ADC is a voltage-to-digital converter that uses oversampling, digital filtering, and noise shaping to obtain high resolution from low-noise analog inputs. Within the data-converter hierarchy, the MCP3426 belongs to the delta-sigma ADC family, which is a type of ADC used for precision measurement. Its two-channel differential architecture suits instrumentation, industrial sensing, and low-frequency process-control systems where accurate conversion of small analog signals is more important than maximum sampling speed.
The principal features include up to 16-bit resolution, two analog input channels, an integrated 2.048 V reference, differential input capability, an I2C interface, and operation from 2.7 V to 5.5 V. The A4 configuration converts at 15 samples per second, providing a comparatively slow conversion rate that supports high-resolution, low-noise acquisition. The manufacturer identifies the operating temperature range as -40 °C to +125 °C, making the device suitable for industrial and extended-temperature equipment.
The converter’s sigma-delta architecture shifts much of the signal processing into the digital filter. This is useful when measuring slowly changing sensor outputs because in-band noise can be reduced without requiring a high-frequency SAR converter. Differential inputs also allow a sensor to be measured across two signal nodes, rejecting common-mode disturbances when the sensor return is referenced appropriately. The integrated reference removes the need for an external reference source, simplifying analog front-end design.
Typical uses include pressure and temperature sensor acquisition, current measurement, laboratory instrumentation, environmental monitoring, and low-speed industrial data logging. In these systems, the MCP3426A4-E/SN can digitize a differential sensor output and report the conversion through the I2C bus to a microcontroller or embedded controller. The 240 samples-per-second device-family maximum provides design margin for configurations that require faster acquisition than the A4 operating rate.
For reliable implementation, follow the manufacturer datasheet for analog input biasing, bypass-capacitor placement, I2C pull-up selection, and input common-mode limits. Pay particular attention to source impedance and differential polarity because excessive impedance or an out-of-range common-mode voltage can degrade conversion accuracy. Place input and supply decoupling close to their associated pins and route the differential pair to minimize pickup of switching noise.
This product page combines the manufacturer’s published device characteristics with practical application guidance, pin-assignment information, lifecycle status, sourcing workflow, and a constrained comparison of directly relevant family variants. It is designed to help engineers determine whether the MCP3426A4-E/SN matches the resolution, channel count, interface, speed, package, and temperature requirements of a new precision-measurement design.
ドロップイン代替品: MCP3426A4-E/SN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP3426A4-E/SN (同一形状・フットプリント) — 相違点: Differential Input Range, Package, Operating Temperature Range, Number of Input Channels, Resolution.
MCP3426A4T-E/SN
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP3426A4-E/SN 最大定格&電気的特性
| ADC Type | Sigma-delta |
| 分解能 | 16 bit |
| Number of Input Channels | 2 channels |
| Maximum Conversion Rate | 240 samples/s |
| A4 Conversion Rate | 15 samples/s |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Digital Interface | I2C |
| Input Type | Differential |
| 動作温度範囲 | -40 °C to +125 °C |
| パッケージ | 8-pin SOIC |
| 実装タイプ | Surface mount |
| RoHS ステータス | Compliant |
MCP3426A4-E/SN ピン構成
| ピン 1 | SCL — I2C clock input |
| ピン 2 | SDA — I2C bidirectional data input and output |
| ピン 3 | AIN1+ — Positive input for analog channel 1 |
| ピン 4 | AIN1- — Negative input for analog channel 1 |
| ピン 5 | AIN0+ — Positive input for analog channel 0 |
| ピン 6 | AIN0- — Negative input for analog channel 0 |
| ピン 7 | VSS — Ground connection |
| ピン 8 | VDD — Positive supply connection |
主な用途
MCP3426A4-E/SN の用途: 6 件s: Precision Temperature Sensing, Industrial Pressure Sensor Acquisition, Battery Current Measurement, Environmental Monitoring, Laboratory Instrumentation, Data Logging and Sensor Hubs.
Precision Temperature Sensing
The MCP3426A4-E/SN is appropriate for ratiometric or differential temperature-sensor interfaces that require accurate, slow measurements rather than high-speed sampling. Its 16-bit resolution and 15-sample-per-second A4 conversion rate provide a useful balance for thermal monitoring, where sensor drift is normally much slower than the ADC conversion rate. The integrated 2.048 V reference stabilizes the measurement reference, while the differential input architecture can reduce common-mode errors when the sensor return is properly connected. In a practical circuit, the sensor drives AIN0+ and AIN0-, with filtering placed close to the converter. The designer should verify that the sensor excitation, output voltage, and common-mode level remain within the input limits and account for the 2.7 V to 5.5 V supply requirement when choosing pull-up and protection components.
おすすめ
Industrial Pressure Sensor Acquisition
The MCP3426A4-E/SN can digitize differential outputs from bridge and strain-gauge pressure sensors when the measured signal changes at a rate compatible with 15 samples per second. Its 16-bit resolution can preserve small changes in sensor output, while the ±2.048 V differential range provides room for bipolar signals around the internal reference. The two analog channels allow a pressure transducer and a temperature reference or calibration channel to be acquired with one converter. Place input filtering and sensor excitation decoupling near the PCB rather than routing the sensitive pair across switching nodes. The 2.7 V to 5.5 V operating range supports common embedded supply rails, but the final front end must maintain the common-mode voltage required by the sensor and should include protection suitable for the industrial environment.
おすすめ
Battery Current Measurement
The MCP3426A4-E/SN is useful for low-rate battery or energy-storage current measurements where a shunt produces a differential voltage. At 15 samples per second in the A4 configuration, it can capture gradual current changes without the conversion burden of a high-rate ADC. The 2.048 V internal reference allows a shunt amplifier to be scaled against a stable reference, and the second channel can monitor a related voltage or current channel. Designers should select the shunt and amplifier for low offset and noise because converter resolution does not eliminate errors contributed by the analog front end. Differential routing, grounding, and isolation from switching converters are critical, particularly when the shunt sits near a high-current power path. The complete measurement chain must remain compatible with the ADC's 2.7 V to 5.5 V supply and input limits.
おすすめ
Environmental Monitoring
The MCP3426A4-E/SN fits environmental monitoring systems that measure slowly changing gas, humidity, or water-quality sensor outputs through differential amplifier stages. The A4 operating rate of 15 samples per second is appropriate for periodic readings, while up to 16-bit resolution can improve the useful dynamic range of small sensor signals. Two input channels can serve two sensor nodes, a reference channel, or a diagnostic input. A practical implementation should use low-leakage protection components because sensor outputs may source only microamps, and it should place anti-alias filtering at the analog inputs. The internal 2.048 V reference reduces the component count, while I2C permits periodic readings from a host microcontroller. Verify that each sensor signal remains inside the differential and common-mode limits throughout its operating range.
おすすめ
Laboratory Instrumentation
The MCP3426A4-E/SN is appropriate for bench instruments that measure slowly varying, low-level differential voltages and need accurate digital results. Its 16-bit resolution, integrated reference, and dual-channel architecture can simplify front-panel sensor conditioning or calibration logging. The 15-sample-per-second A4 rate suits meters, chart recorders, and process-calibration equipment, although it should not be selected for waveform capture or fast transient analysis. Use the second channel to capture a reference or monitor an excitation source, and retain a separate precision reference path if absolute accuracy requirements exceed the internal reference performance. PCB layout should keep the differential inputs away from relay contacts, display drivers, and other switching devices. Firmware must also accommodate the converter's configured data rate and conversion latency before reporting a measurement.
おすすめ
Data Logging and Sensor Hubs
The MCP3426A4-E/SN can serve as the analog acquisition element in a compact industrial or building sensor hub. Two differential channels can monitor two slow sensor outputs, while the I2C interface connects the converter to a host processor without requiring a dedicated parallel data bus. The A4 rate of 15 samples per second is appropriate for periodic logging of temperature, pressure, flow proxies, and similar signals. Integrated 2.048 V reference and 16-bit resolution reduce front-end complexity, although external calibration may be required for stringent system accuracy. Select passive filtering components carefully so that settling time is adequate for the operating mode and source impedance. The converter should be powered from a clean regulated rail, and the host firmware should detect conversion completion and identify each channel consistently after power-up.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP3426A4-E/SN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCP3426A4T-E/SN |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology |
| ADC Type | Sigma-delta | Sigma-delta |
| Resolution | 16 bit | 16 bit |
| Input Channels | 2 channels | 2 channels |
| A4 Conversion Rate | 15 samples/s | 15 samples/s |
| Internal Reference | 2.048 V | 2.048 V |
| Differential Input Range | ±2.048 V | ±2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Digital Interface | I2C | I2C |
| Operating Temperature Range | -40 °C to +125 °C | Confirm suffix-specific rating in the Microchip ordering table |
主な差別化要因
- Integrated precision reference simplifies the measurement chain (vs MCP3426A4T-E/SN)
- A4 operating mode prioritizes precision over maximum throughput (vs MCP3426A4T-E/SN)
- Two differential channels in a compact 8-pin SOIC (vs MCP3426A4T-E/SN)
設計ノート
Route AIN0+ and AIN0- as a closely coupled differential pair, and do the same for AIN1+ and AIN1-. Keep these traces away from switching-regulator outputs, relay contacts, crystals, and high-current paths. Place input filtering close to the corresponding pins and connect the return path to the device ground reference without sharing narrow segments with noisy currents.
The MCP3426A4-E/SN operates from 2.7 V to 5.5 V. Place the required supply bypass capacitor close to VDD and VSS, and verify that the selected regulator remains stable with the converter's load transitions. Because the device uses an internal 2.048 V reference, measurement accuracy still depends on clean supply voltage and low-noise analog layout; an unstable or noisy supply can degrade the acquired result.
Do not treat the 240-sample-per-second family maximum as the MCP3426A4-E/SN conversion rate; the A4 configuration operates at 15 samples per second. Firmware must allow enough conversion time before reading a completed result. Also confirm differential polarity, input common-mode limits, and source impedance because a numerically correct ADC cannot compensate for an out-of-range or improperly biased analog input.
Avoid long analog traces through electrically noisy board regions. Use continuous ground planes, return both differential inputs through the same analog section, and consider guarding sensitive nodes if leakage from high-impedance sensors is significant. The digital I2C lines may be longer than the analog pair, but they still require suitable pull-up resistors and should be kept separate from sensitive input traces to minimize conversion injection.
コンプライアンス情報
The component listing identifies MCP3426A4-E/SN as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive-qualification statement is established by the available technical information.