MCP604T-I/ST - Quad 2.8MHz Low-Power Op Amp | Microchip
部品番号: MCP604T-I/ST ✓ 生産中MCP604T-I/ST 概要
An operational amplifier is an active analog signal-conditioning device that uses high open-loop gain to amplify small differential inputs. The MCP604 belongs to the CMOS operational-amplifier hierarchy, where rail-to-rail output swing allows the output voltage to approach the supply rails more closely than a conventional amplifier with a restricted output range. Four independent amplifiers in the MCP604 can perform buffering, amplification, filtering, comparison, or level-shifting functions while conserving board area.
Key features include four amplifier channels, a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, low input bias current, high open-loop gain, and rail-to-rail output swing. The 2.7 V to 6 V operating range allows the device to operate from single 3.3 V or 5 V rails as well as conventional low-voltage analog systems. The industrial-temperature ordering code MCP604T-I/ST identifies the temperature grade and TSSOP packaging option.
Microchip's advanced CMOS process gives the MCP604 low bias current, high-speed operation, high open-loop gain, and rail-to-rail output capability. Its 2.8 MHz gain-bandwidth product is sufficient for audio-frequency, general-purpose, and low-to-moderate-bandwidth signal paths. Because the amplifier is intended for low-power systems, stable operation also depends on correct input/output capacitor selection, suitable bypassing, and keeping sensitive input traces away from switching nodes.
Typical uses include portable sensor interfaces, low-power data acquisition, industrial transducers, audio signal conditioning, battery-powered measurement equipment, and general analog buffering. Four channels can process related signals simultaneously or provide independent gain stages around a microcontroller, ADC, or sensor network. The low operating current helps limit system power when the amplifier operates continuously, although the final system dissipation also depends on load and supply voltage.
For stable operation, place the bypass capacitor close to the supply pin, use the manufacturer-recommended feedback network, and verify output-swing and common-mode limits against the actual signal and supply levels. Avoid placing high-impedance input traces beside noisy switching paths, and use a low-impedance source where the source impedance could create bias-current errors. The TSSOP footprint also requires adequate board spacing for soldering and inspection.
This product record combines the manufacturer architecture information, exact ordering information, package details, and verified sourcing context. It also provides engineering-focused alternatives, application guidance, comparison parameters, and practical design notes to help evaluate the MCP604T-I/ST before PCB implementation.
ドロップイン代替品: MCP604T-I/ST — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP604T-I/ST (同一形状・フットプリント) — 相違点: Package, Amplifier Type, Number of Channels, Amplifier Count, Input Common-Mode Range.
MCP604T-E/ST
✅ ドロップイン価格はお問い合わせください
データシートを見る →MCP604T-E/STVAO
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP604T-I/SL
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MCP604T-I/ST 最大定格&電気的特性
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 6 V |
| Output Swing | Rail-to-rail |
| パッケージ | 14-pin TSSOP |
| 実装タイプ | Surface mount |
| Process Technology | Advanced CMOS |
MCP604T-I/ST 14-pin tssop ピン配置ガイド
MCP604T-I/ST (14-pin tssop パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: MCP604T-I/ST.
詳細は データシート をご参照ください。
主な用途
MCP604T-I/ST の用途: 6 件s: Portable Sensor Signal Conditioning, Industrial Transducer Interface, Low-Power Data Acquisition, Audio Signal Buffering, Battery-Powered Measurement, Embedded Analog Control.
Portable Sensor Signal Conditioning
The MCP604T-I/ST fits portable sensor interfaces because its four channels can amplify, buffer, and filter several low-level signals while the typical operating current is only 230 uA. The 2.7 V minimum supply voltage supports compact, low-energy systems operating from a 3.3 V rail. Place each amplifier close to its sensor or connector, bypass the supply locally, and use short, guarded traces to limit noise pickup. The 2.8 MHz gain-bandwidth product provides useful bandwidth for common pressure, temperature, and resistive-sensor signals, although sensor-specific filtering and input-offset requirements still need verification.
おすすめ
Industrial Transducer Interface
The MCP604T-I/ST is appropriate for industrial transducer conditioning where a 2.7 V to 6 V supply, low typical operating current of 230 uA, and four independent amplifier channels simplify analog front ends. Its 2.8 MHz gain-bandwidth product can support general-purpose measurement paths with moderate bandwidth. Use one channel for a sensor signal, other channels for excitation, reference conditioning, or output buffering, and observe ESD protection requirements at external connectors. The industrial ordering code should be checked against the actual enclosure temperature and production qualification requirements.
おすすめ
Low-Power Data Acquisition
The MCP604T-I/ST can condition four analog inputs before digitization in a compact data-acquisition system. Its 230 uA typical operating current limits the amplifier contribution to standby consumption, while the 2.8 MHz gain-bandwidth product is suitable for many sensor-bandwidth signals. Configure gain carefully so the closed-loop bandwidth remains appropriate for the signal, and account for input offset and bias-current error when using high-impedance sources. Local supply bypassing and short feedback paths are essential for repeatable measurements at low signal levels.
おすすめ
Audio Signal Buffering
The MCP604T-I/ST is useful for audio signal buffering and gain stages where rail-to-rail output operation helps preserve signal range in low-voltage systems. Its 2.8 MHz gain-bandwidth product covers a substantial portion of the audio band, and four channels allow paired stereo buffering plus additional monitoring or control paths. Confirm the required gain-bandwidth product, output-load conditions, distortion criteria, and noise performance for the selected gain and frequency. Keep input and output routing short and decouple the supply close to the device to reduce channel-to-channel interaction.
おすすめ
Battery-Powered Measurement
The MCP604T-I/ST is well suited to battery-powered measurement instruments because it starts at 2.7 V, consumes 230 uA typically, and integrates four amplifier channels. The device can condition battery voltage, sensor outputs, and status signals without requiring a large number of separate packages. Use the lowest supply voltage that still provides adequate output swing and common-mode headroom, and disable or bypass unneeded channels according to the family documentation. Battery-life estimates should include regulator quiescent current, ADC activity, and the load driven by each amplifier output.
おすすめ
Embedded Analog Control
The MCP604T-I/ST can provide four independent analog functions around an embedded controller, including sensor amplification, actuator feedback, reference buffering, and threshold conditioning. The 2.7 V to 6 V range is compatible with common embedded rails, while 230 uA typical current supports low-power operation. The package reduces routing complexity by grouping four channels in one 14-pin TSSOP footprint. Keep sensitive feedback and reference nets away from MCU clock and power-converter traces, and verify output drive against the connected ADC, DAC, or actuator input.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP604T-I/ST — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCP604T-E/ST | MCP604T-E/STVAO | MCP604T-I/SL |
|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Process Technology | Advanced CMOS | Advanced CMOS | Advanced CMOS | Advanced CMOS |
| Ordering Grade | Industrial I grade | E grade | Automotive-oriented VAO ordering option | Industrial I grade |
主な差別化要因
- Four independent amplifiers in one compact package (vs MCP604T-E/ST)
- Low operating current for four-channel analog conditioning (vs MCP604T-E/STVAO)
- Single-supply compatibility (vs MCP604T-E/ST)
設計ノート
Place the supply bypass capacitor directly between the MCP604T-I/ST supply and ground pins, keeping the connection loop short and the return path close to the device. Route sensitive input and feedback traces away from digital clock lines, switching-regulator nodes, and the amplifier outputs. With four channels in a 14-pin TSSOP, plan the fanout so each amplifier's feedback components remain close to the associated input and output pins and do not force signals around the package.
Choose closed-loop gain with the 2.8 MHz gain-bandwidth product in mind. Higher gain reduces the usable closed-loop bandwidth, so a gain of 10 leaves substantially less bandwidth than unity gain. When driving a capacitive load, add an isolation resistor near the amplifier output and verify stability. For high-impedance sensors, account for input bias-current error and leakage by keeping the source impedance within the manufacturer-recommended range.
Do not interpret the 2.7 V minimum supply rating as permission to operate every output at either rail under every load. Check the input common-mode range, output-swing curve, capacitive-load behavior, and shutdown-channel configuration in the manufacturer datasheet. Likewise, avoid assuming that the four amplifier channels are interchangeable in every operating mode; identify unused inputs and outputs according to the official pin-description and application guidance.
The 230 uA value is a typical family operating-current specification, not a complete system-power limit. Actual current depends on supply voltage, amplifier activity, output load, and the selected operating mode. For battery designs, calculate the amplifier contribution at the intended duty cycle and include regulator, ADC, logic, and indicator currents. Use the most efficient operating configuration that still meets settling-time and noise requirements.
コンプライアンス情報
The standard MCP604T-I/ST is not identified as an automotive-qualified ordering option. The automotive-oriented MCP604T-E/STVAO alternative should be selected when automotive qualification is specifically required.