MK10DN512VLK10 - Kinetis K10 512KB Flash 100MHz MCU | NXP | 80-LQFP
部品番号: MK10DN512VLK10 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $12.45 | $12.45 |
| 10 | $11.21 | $112.10 |
| 100 | $9.85 | $985.00 |
| 500 | $8.92 | $4,460.00 |
| 1,000 | $8.1 | $8,100.00 |
MK10DN512VLK10 概要
An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core implementing the Thumb-2 instruction set, an optional single-precision floating-point unit, DSP extensions, and a Nested Vectored Interrupt Controller (NVIC). Kinetis K-series MCUs belong to the wider NXP Kinetis portfolio, which itself is a sub-family of ARM Cortex-M based microcontrollers. They sit within the integrated circuit category of power management and embedded control devices. Compared with Cortex-M0/M0+ parts, the M4 adds DSP and FPU capability for motor control and signal processing; compared with Cortex-M7, it is lower-power and lower-cost while retaining sufficient performance for many industrial and consumer tasks.
Key features include 512 KB dual-bank flash with EEPROM capability, 128 KB SRAM, high-speed 16-bit ADC, comparators, DAC, op-amps on-chip, USB OTG (full-speed) with integrated PHY, multiple serial peripherals (UART, SPI, I2C, I2S), low-power timer, RTC, and a 4-channel DMA. The on-chip analog integration reduces BOM for sensor conditioning and closed-loop control. Hardware security and tamper features plus a wide operating temperature range (-40C to +105C) make the part suitable for industrial and white-goods designs.
The MK10DN512VLK10 uses a Cortex-M4 core with 3-stage pipeline, branch speculation, and configurable single-precision FPU. Memory is organized as 512 KB primary flash with flash access control and 128 KB system SRAM. Peripherals are interconnected via a crossbar switch with arbitration, allowing simultaneous DMA-driven transfers while the CPU executes application code.
Typical applications include industrial control and HMI, low-cost motor drives, building automation, smart metering, USB peripherals, consumer electronics and medical instruments. The wide temperature range also supports outdoor and ruggedized installations. When designing with this part, allocate sufficient decoupling (100 nF + bulk) near each VDD/VSS pair and follow the LQFP-80 land pattern recommendations; for USB-OTG designs add the required 90-ohm differential routing and proper PCB stackup for the DP/DM traces.
ドロップイン代替品: MK10DN512VLK10 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MK10DN512VLK10 （同一形状・フットプリント） — 相違点: Package, Core, Maximum CPU Frequency, Mounting Type, Core Architecture.
クイック比較ツール — 並列比較する代替部品を選択:
MK10DN512ZVLK10
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MK10DN512VLL10
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MK20DN512VLK10
✅ ドロップイン✓ 在庫あり
$5.36 / 個
データシートを見る →MK10DN256VLK10
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MK10DX256VLK10
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MKL04Z8VTG4
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MK10DN512VLK10 最大定格＆電気的特性
| Manufacturer | NXP Semiconductors |
| Series | Kinetis K10 |
| Core | ARM Cortex-M4 with FPU |
| Core Size | 32-Bit |
| Maximum CPU Clock | 100 MHz |
| Program Memory Size | 512 KB (512K x 8) Flash |
| RAM Size | 128 KB |
| EEPROM Capacity | On-chip emulated EEPROM |
| Supply Voltage Range | 1.71 V to 3.6 V |
| 動作温度範囲 | -40C to +105C |
| パッケージ | 80-LQFP (12 x 12 mm) |
| 実装タイプ | Surface Mount |
| Package Type | LQFP-80 |
| USB | USB OTG Full-Speed with on-chip PHY |
| Connectivity | I2C, SPI, UART, I2S, USB OTG, CAN |
| Peripherals | DMA, PWM, WDT, RTC, ADC, DAC, Op-amps, Comparators |
| Data Converters | 16-bit ADC, 12-bit DAC |
| MSLレベル | MSL 3 (168 hours) |
| RoHS ステータス | Compliant |
MK10DN512VLK10 ピン構成
| ピン 1 | PTE0 — Port E GPIO / peripheral |
| ピン 2 | PTE1 — Port E GPIO / peripheral |
| ピン 3 | PTE2 — Port E GPIO / peripheral |
| ピン 4 | PTE3 — Port E GPIO / peripheral |
| ピン 5 | PTE4 — Port E GPIO / peripheral |
| ピン 6 | PTE5 — Port E GPIO / peripheral |
| ピン 7 | PTE6 — Port E GPIO / peripheral |
| ピン 8 | VSS — Ground |
| ピン 9 | PTE7 — Port E GPIO / peripheral |
| ピン 10 | PTE8 — Port E GPIO / peripheral |
| ピン 11 | PTE9 — Port E GPIO / peripheral |
| ピン 12 | PTE10 — Port E GPIO / peripheral |
| ピン 13 | PTE11 — Port E GPIO / peripheral |
| ピン 14 | PTE12 — Port E GPIO / peripheral |
| ピン 15 | VDD — Core supply voltage |
| ピン 16 | VSS — Ground |
| ピン 17 | PTA0 — Port A GPIO / peripheral |
| ピン 18 | PTA1 — Port A GPIO / peripheral |
| ピン 19 | PTA2 — Port A GPIO / peripheral |
| ピン 20 | PTA3 — Port A GPIO / peripheral |
| ピン 21 | PTA4 — Port A GPIO / peripheral |
| ピン 22 | PTA5 — Port A GPIO / peripheral |
| ピン 23 | PTA6 — Port A GPIO / peripheral |
| ピン 24 | PTA7 — Port A GPIO / peripheral |
| ピン 25 | PTA8 — Port A GPIO / peripheral |
| ピン 26 | PTA9 — Port A GPIO / peripheral |
| ピン 27 | PTA10 — Port A GPIO / peripheral |
| ピン 28 | PTA11 — Port A GPIO / peripheral |
| ピン 29 | PTA12 — Port A GPIO / peripheral |
| ピン 30 | PTA13 — Port A GPIO / peripheral |
| ピン 31 | PTA14 — Port A GPIO / peripheral |
| ピン 32 | PTA15 — Port A GPIO / peripheral |
| ピン 33 | PTA16 — Port A GPIO / peripheral |
| ピン 34 | PTA17 — Port A GPIO / peripheral |
| ピン 35 | PTB0 — Port B GPIO / peripheral |
| ピン 36 | PTB1 — Port B GPIO / peripheral |
| ピン 37 | PTB2 — Port B GPIO / peripheral |
| ピン 38 | PTB3 — Port B GPIO / peripheral |
| ピン 39 | PTB4 — Port B GPIO / peripheral |
| ピン 40 | PTB5 — Port B GPIO / peripheral |
| ピン 41 | PTB6 — Port B GPIO / peripheral |
| ピン 42 | PTB7 — Port B GPIO / peripheral |
| ピン 43 | PTB8 — Port B GPIO / peripheral |
| ピン 44 | PTB9 — Port B GPIO / peripheral |
| ピン 45 | PTB10 — Port B GPIO / peripheral |
| ピン 46 | PTB11 — Port B GPIO / peripheral |
| ピン 47 | PTB12 — Port B GPIO / peripheral |
| ピン 48 | PTB13 — Port B GPIO / peripheral |
| ピン 49 | PTB14 — Port B GPIO / peripheral |
| ピン 50 | PTB15 — Port B GPIO / peripheral |
| ピン 51 | PTB16 — Port B GPIO / peripheral |
| ピン 52 | PTB17 — Port B GPIO / peripheral |
| ピン 53 | PTC0 — Port C GPIO / peripheral |
| ピン 54 | PTC1 — Port C GPIO / peripheral |
| ピン 55 | PTC2 — Port C GPIO / peripheral |
| ピン 56 | PTC3 — Port C GPIO / peripheral |
| ピン 57 | PTC4 — Port C GPIO / peripheral |
| ピン 58 | PTC5 — Port C GPIO / peripheral |
| ピン 59 | PTC6 — Port C GPIO / peripheral |
| ピン 60 | PTC7 — Port C GPIO / peripheral |
| ピン 61 | PTC8 — Port C GPIO / peripheral |
| ピン 62 | PTC9 — Port C GPIO / peripheral |
| ピン 63 | PTC10 — Port C GPIO / peripheral |
| ピン 64 | PTC11 — Port C GPIO / peripheral |
| ピン 65 | PTC12 — Port C GPIO / peripheral |
| ピン 66 | PTC13 — Port C GPIO / peripheral |
| ピン 67 | PTC14 — Port C GPIO / peripheral |
| ピン 68 | PTC15 — Port C GPIO / peripheral |
| ピン 69 | PTC16 — Port C GPIO / peripheral |
| ピン 70 | PTC17 — Port C GPIO / peripheral |
| ピン 71 | PTD0 — Port D GPIO / peripheral |
| ピン 72 | PTD1 — Port D GPIO / peripheral |
| ピン 73 | PTD2 — Port D GPIO / peripheral |
| ピン 74 | PTD3 — Port D GPIO / peripheral |
| ピン 75 | PTD4 — Port D GPIO / peripheral |
| ピン 76 | PTD5 — Port D GPIO / peripheral |
| ピン 77 | PTD6 — Port D GPIO / peripheral |
| ピン 78 | PTD7 — Port D GPIO / peripheral |
| ピン 79 | VSS — Ground |
| ピン 80 | VDD — Core supply voltage |
主な用途
MK10DN512VLK10 の用途: 6 件s: Industrial Motor Control and Drives, Building Automation and HVAC Controllers, USB Peripherals and HID Devices, Smart Energy Meters and Measurement, Medical and Health Monitoring Devices, Consumer Electronics and HMI Panels.
Industrial Motor Control and Drives
The MK10DN512VLK10 fits industrial motor control designs because its Cortex-M4 with FPU executes single-cycle MAC instructions needed for field-oriented control (FOC) loops, while the 100 MHz clock supports moderate PWM frequencies up to 20 kHz with full PID update each cycle. The on-chip 16-bit ADC and FlexTimer PWM module provide simultaneous current sensing and three-phase PWM generation without external components. The 512 KB flash holds FOC libraries and application code with room for field updates, while 128 KB RAM supports dual-shunt current sampling buffers and stack-heavy control structures. Compared with Cortex-M0 parts, the M4 with FPU delivers 3-4x faster FOC step times for PMSM and BLDC motors under 1 kW. Industrial-grade -40C to +105C operation handles drive cabinet environments without derating.
おすすめ
Building Automation and HVAC Controllers
The MK10DN512VLK10 suits building automation controllers because its rich mixed-signal peripherals integrate op-amps, comparators, 16-bit ADC and 12-bit DAC for direct sensor conditioning on the PCB, reducing analog BOM. The 512 KB flash comfortably stores BACnet or Modbus stacks plus HVAC state machines, while USB OTG full-speed enables local commissioning and firmware updates from a laptop. The wide 1.71 V to 3.6 V supply range tolerates typical 24 V industrial rail step-down outputs with margin. Compared with smaller Kinetis K0 parts, the MK10's larger SRAM supports multi-protocol stacks (Modbus + BACnet + proprietary) concurrently. The -40C to +105C rating handles unheated basement and rooftop enclosures.
おすすめ
USB Peripherals and HID Devices
The MK10DN512VLK10 targets USB peripherals because the on-chip USB OTG full-speed PHY eliminates external USB transceivers, saving PCB area and BOM cost in HID, custom-keyboards, USB sensors, and USB-to-UART bridge designs. The Cortex-M4 with FPU handles HID report processing and on-board DSP such as audio or gesture recognition at 100 MHz without CPU bottleneck. The 512 KB flash fits USB stack plus composite device classes (HID + CDC + vendor), while 128 KB RAM supports double-buffered USB endpoints. The 80-LQFP package is cost-effective and easily hand-solderable for prototypes. Compared with Cortex-M0+ USB parts, the MK10 offers more flash for richer device firmware.
おすすめ
Smart Energy Meters and Measurement
The MK10DN512VLK10 fits single-phase smart meter designs because its on-chip 16-bit ADC and op-amps support direct current-sensing analog front ends, while the Cortex-M4 with FPU computes RMS, harmonics and power-quality metrics efficiently. The 512 KB flash stores DLMS/COSEM or proprietary metering stacks plus calibration data, while 128 KB RAM supports simultaneous metrology and communication tasks. The on-chip EEPROM emulation preserves tariff and billing data across power cycles, reducing external memory. The wide operating temperature range handles outdoor meter enclosures. Compared with fixed-function metering ICs, the MK10 offers more flexibility for multi-standard support.
おすすめ
Medical and Health Monitoring Devices
The MK10DN512VLK10 supports medical peripheral and health-monitoring device designs because the on-chip 16-bit ADC and op-amps condition bioelectric signals (ECG, EMG, SpO2 analog front ends) without external instrumentation amplifiers in cost-optimized versions. The Cortex-M4 with DSP extensions executes filtering and feature extraction in real time at low CPU load. The 512 KB flash stores DSP libraries and UI code, while 128 KB RAM supports sample buffers for pulse oximetry and ECG. The -40C to +105C range covers portable and clinical environments. Designers targeting FDA/IEC 62304 certification should still validate full IEC 60601 EMI/ESD performance at the system level.
おすすめ
Consumer Electronics and HMI Panels
The MK10DN512VLK10 fits consumer HMI panels and appliances because the Cortex-M4 with FPU drives capacitive-touch processing and graphical UI rendering on segment LCD or low-cost TFT displays efficiently at 100 MHz. The 512 KB flash holds rich UI assets and connectivity stacks, while 128 KB RAM supports frame buffers and USB upgrade paths. The on-chip op-amps and comparators interface directly with capacitive touch sensors and rotary encoders. Compared with Cortex-M0+ parts, the M4 supports smoother animation and more complex UI logic. The wide temperature range handles appliance and outdoor consumer environments.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MK10DN512VLK10 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MK10DN512ZVLK10 | MK20DN512VLK10 | MK10DN256VLK10 | MK10DX256VLK10 | MK10DN512VLL10 |
|---|---|---|---|---|---|---|
| Package | 80-LQFP (12x12 mm) | 80-LQFP (12x12 mm) - same | 80-LQFP (12x12 mm) - same | 80-LQFP (12x12 mm) - same | 80-LQFP (12x12 mm) - same | 100-LQFP - different (not drop-in) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU |
| Maximum CPU Clock | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Flash Size | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 256 KB (-50%) | 512 KB |
| RAM Size | 128 KB | 128 KB | 128 KB | 64 KB (-50%) | 32 KB (-75%) | 128 KB |
| USB OTG | Yes (full-speed with on-chip PHY) | Yes (full-speed) | Yes (full-speed) | Yes (full-speed) | Yes (full-speed) | Yes (full-speed) |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C |
| Security / Tamper | Standard | Standard | Enhanced (security/tamper) | Standard | Standard (low-power variant) | Standard |
主な差別化要因
- On-chip USB OTG full-speed PHY eliminates external transceiver （vs MKL04Z8VTG4)
- Larger flash and RAM versus K10 256KB variants （vs MK10DN256VLK10)
- Same 80-LQFP footprint as K20 sub-family for easy upgrade （vs MK20DN512VLK10)
設計ノート
Decoupling: place a 100 nF ceramic cap as close as possible to each VDD/VSS pin pair on the MK10DN512VLK10. Add a 4.7 uF or 10 uF bulk capacitor on each main VDD rail near the MCU. Use a ferrite bead or small inductor if the digital supply shares a rail with analog VREF to prevent digital noise coupling into ADC reference voltage.
PCB layout: route USB DP and DM as a 90-ohm differential pair with controlled impedance, keep them short and away from switching nodes. Provide a 4-layer or 2-layer PCB stackup with continuous ground plane under the MCU to reduce EMI. Exposed pad (if any) of the LQFP package is not present; standard lead-frame leads only.
Programming: the MK10DN512VLK10 enters reset if NMI/test pins are inadvertently asserted. Configure reset and NMI pins with proper pull-ups (typically 10 kohm) and follow the Kinetis flash programming guide before in-system programming. Watchdog must be serviced in low-power modes or it will reset the part unexpectedly.
Estimated: at 100 MHz CPU clock, typical core supply current is around 30-40 mA, leading to ~0.1 W dissipation. At maximum CPU loading with peripherals active, dissipation can reach 0.3-0.4 W. The 80-LQFP package has theta_JA around 50-60 C/W, yielding a junction temperature rise of ~25 C above ambient, which is well within the 105C maximum rating.
コンプライアンス情報
RoHS compliant per NXP product page. Not AEC-Q100 qualified - choose KEA or S32K automotive parts for AEC-Q100 automotive applications.
