MPC859DSLZP50A - PowerQUICC 50MHz Comm Processor | NXP | BGA-357
部品番号: MPC859DSLZP50A ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $78.5 | $78.50 |
| 10 | $72 | $720.00 |
| 100 | $65 | $6,500.00 |
| 500 | $58 | $29,000.00 |
| 1,000 | $52.5 | $52,500.00 |
MPC859DSLZP50A 概要
Background Knowledge: A PowerQUICC (Power Architecture QUICC) integrated communications processor is a system-on-chip that combines a high-performance Power Architecture CPU core with dedicated communications peripheral engines such as serial communication controllers, ATM controllers, and fast Ethernet MACs. It sits in the hierarchy of communications ICs > network processors > embedded processors > microprocessors, and historically bridged the gap between general-purpose MCUs and dedicated network ASICs for telecom/datacom infrastructure.
Key features of the MPC859DSLZP50A include a single 32-bit Power Architecture core at 50 MHz, dual 10/100 Mbps Ethernet MACs, multiple serial communication controllers (SCCs), an ATM Utopia interface, and a peripheral bus supporting up to 32 address bits. The device operates from a 1.8 V core supply and 3.3 V I/O supply. It is specifically tailored for DSL modems, integrated access devices (IADs), and residential gateways, where its CPM (Communications Processor Module) offloads protocol processing from the CPU.
The MPC859DSL uses a 0.18-micron CMOS process with low-power modes including doze, sleep, and deep-sleep, allowing idle power reduction in always-on CPE equipment. The CPM can independently handle SCC, SMC, SPI, I2C, and USB protocol layers, enabling wire-speed WAN-side framing without CPU intervention.
Typical applications include DSL modems, integrated access devices (IADs), residential gateways, SOHO routers, and industrial serial-protocol bridges. Its combination of Ethernet MACs, ATM support, and multi-protocol SCCs makes it especially well-suited for converged voice/data CPE where multiple T1/E1, UART, or HDLC links must be aggregated onto an Ethernet uplink.
Design consideration: Because this part is end-of-life on NXP's product page, designers evaluating it for new designs should plan for last-time-buy and consider NXP's QorIQ or PowerQUICC II/III successors for greenfield projects, while the MPC859DSL remains a viable pin-compatible upgrade for legacy repair and existing designs.
This page synthesizes distributor stock signals, NXP's end-of-life notices, and practical design notes on the MPC866/859 PowerQUICC family that are not consolidated in a single manufacturer document.
ドロップイン代替品: MPC859DSLZP50A — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MPC859DSLZP50A （同一形状・フットプリント） — 相違点: Operating Temperature, Package, Mounting Type, Process Technology, Core Frequency.
クイック比較ツール — 並列比較する代替部品を選択:
MPC859DSLV50A
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC859DSLVR66A
✅ ドロップイン✓ 在庫あり
$23.85 / 個
データシートを見る →MPC859DSLVR50A
✅ ドロップイン✓ 在庫あり
$19.85 / 個
データシートを見る →MPC866DSLZP50A
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC866DSLV50A
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC859DSLZP50A 最大定格＆電気的特性
| Processor Type | MPC8xx PowerQUICC Integrated Communications Controller |
| Core Architecture | 32-bit Power Architecture |
| Number of Cores | 1 |
| Core Frequency | 50 MHz |
| Core Supply Voltage | 1.8 V |
| I/O Supply Voltage | 3.3 V |
| パッケージ / ケース | 357-PBGA (25x25 mm) |
| 動作温度 | 0 C to +95 C |
| Packaging | Tray |
| Lead Free Status | Contains Lead |
| RoHS ステータス | RoHS |
| Ethernet MACs | 2 x 10/100 Mbps |
| Process Technology | 0.18 micron CMOS |
| 実装タイプ | Surface Mount |
| Lifecycle | End of Life per NXP product page |
MPC859DSLZP50A 357-pbga (25x25 mm) ピン配置ガイド
MPC859DSLZP50A (357-pbga (25x25 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MPC859DSLZP50A.
詳細は データシート をご参照ください。
主な用途
MPC859DSLZP50A の用途: 6 件s: DSL Modem CPE, Integrated Access Device (IAD), Residential Gateway / SOHO Router, Industrial Serial Protocol Bridge, Legacy Telecom Edge Equipment, ATM-to-Ethernet Aggregation Switch.
DSL Modem CPE
The MPC859DSLZP50A is purpose-built for DSL customer-premises equipment because it integrates dual 10/100 Ethernet MACs, an ATM Utopia interface, and a CPM that handles DSL framing without CPU intervention. At 50 MHz Power Architecture core with 1.8 V core / 3.3 V I/O supplies, it provides the WAN-side aggregation that residential DSL modems need while drawing modest idle power via the CPM doze/sleep modes. This makes it ideal for always-on DSL bridge/router designs that must run continuously without thermal stress.
おすすめ
Integrated Access Device (IAD)
For integrated access devices that combine DSL uplink with VoIP, FXS, and LAN ports, the MPC859DSLZP50A's multi-protocol SCCs, ATM SAR, and dual Ethernet MACs cover the converged voice/data path in a single chip. The 50 MHz Power Architecture core runs the VoIP/RTP stack while the CPM manages ATM AAL2/AAL5 segmentation and HDLC framing on T1/E1 links. The 357-PBGA package supports the I/O density required for 4-port LAN plus 2-port FXS designs without external bridge silicon.
おすすめ
Residential Gateway / SOHO Router
In residential gateway and SOHO router applications, the MPC859DSLZP50A's dual 10/100 Ethernet MACs drive the LAN switch fabric while the Power Architecture core runs NAT/firewall/DHCP services at wire-rate for typical broadband speeds. The CPM offloads PPPoE, PPTP, and IPSec ESP processing, freeing the 50 MHz core for routing tables and QoS classification. Low-power deep-sleep mode also helps the gateway meet energy-efficiency regulations such as the EU Code of Conduct on broadband equipment.
おすすめ
Industrial Serial Protocol Bridge
Beyond telecom, the MPC859DSLZP50A's multiple serial communication controllers (SCCs) and parallel I/O make it a robust platform for industrial protocol bridging - converting multi-drop RS-485 HDLC, UART, or BISYNC links onto Ethernet or ATM uplinks. The 0 to +95 C operating range covers most indoor industrial enclosures, and the 0.18 micron CMOS process provides proven long-term reliability for unattended factory-floor nodes. Designers can implement Modbus TCP, DNP3/IP, or proprietary serial-to-IP bridging on a single chip.
おすすめ
Legacy Telecom Edge Equipment
For legacy telecom edge equipment such as channel banks, digital cross-connect systems, and small-business PBXs, the MPC859DSLZP50A's TDM support, multi-protocol SCCs, and proven PowerQUICC reliability make it a field-deployed workhorse. Designers maintaining installed-base hardware can use it as a repair spare with confidence in long-term support from distributors like Rochester Electronics, while architects planning new platforms should select a current PowerQUICC II/III or QorIQ successor. The 357-PBGA footprint simplifies board-level swaps in existing chassis.
おすすめ
ATM-to-Ethernet Aggregation Switch
For small ATM-to-Ethernet aggregation switches used by ISPs and campus networks, the MPC859DSLZP50A integrates an ATM SAR with the AAL1/AAL2/AAL5 protocols alongside dual Ethernet MACs, eliminating external bridging silicon. At 50 MHz it can sustain multiple T1/E1 ATM links while forwarding Ethernet frames at wire-rate through the CPM's fast-path DMA. The same 357-PBGA footprint across the MPC866/859 family simplifies SKU selection for different port counts.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MPC859DSLZP50A — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MPC859DSLV50A | MPC859DSLVR66A | MPC859DSLVR50A | MPC866DSLZP50A | MPC866DSLV50A |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 357-PBGA (25x25 mm) | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same |
| Core Frequency | 50 MHz | 50 MHz | 66 MHz | 50 MHz | 50 MHz | 50 MHz |
| Core Architecture | 32-bit Power Architecture | 32-bit Power Architecture | 32-bit Power Architecture | 32-bit Power Architecture | 32-bit Power Architecture | 32-bit Power Architecture |
| Lead-Free / RoHS | Contains Lead / RoHS | Lead-free / RoHS | Lead-free / RoHS | Lead-free / RoHS | Contains Lead / RoHS | Lead-free / RoHS |
| Ethernet MACs | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps |
| PCI Bridge | Not bonded | Not bonded | Not bonded | Not bonded | Bonded / active | Bonded / active |
| Operating Temperature | 0 C to +95 C | 0 C to +95 C | 0 C to +95 C | 0 C to +95 C | 0 C to +95 C | 0 C to +95 C |
主な差別化要因
- Integrated ATM SAR with Ethernet MACs （vs MPC859DSLV50A)
- 50 MHz speed grade for cost-sensitive CPE （vs MPC859DSLVR66A)
- MPC859 silicon without PCI bridge （vs MPC866DSLZP50A)
設計ノート
The 357-PBGA package at 50 MHz and 1.8 V core / 3.3 V I/O dissipates on the order of 1-2 W under typical CPE workloads (estimated, based on 50 MHz PowerQUICC family figures). At full CPM activity with all SCCs and both Ethernet MACs active, designers should provide at least 4-layer PCB with a continuous ground plane beneath the BGA and thermal vias under the die-expose pad to keep junction temperature within the 0-95 C operating range.
Route the 357-PBGA with microvia or HDI technology to fan out the 1.0 mm pitch ball grid without necking. Place 0.1 uF decoupling capacitors adjacent to every supply ball, with bulk 10 uF tantalum or ceramic capacitors on the 1.8 V and 3.3 V rails within 25 mm. Maintain 50 ohm controlled impedance on Ethernet MII/RMII traces and keep the 50 MHz system clock traces short and guard-banded.
Because NXP has flagged MPC859DSLZP50A as End of Life, do not design it into new production programs without a written last-time-buy agreement and approved franchised-distributor stock. Designers should also confirm the silicon revision ('A' suffix) matches the firmware in their boot ROM, as some CPM errata are revision-dependent. Verify the system clock PLL configuration against the family datasheet AC timing table before committing to a BOM.
The 1.8 V core and 3.3 V I/O rails require proper power sequencing per the MPC866/859 hardware specifications: the 3.3 V I/O supply must be present before or coincident with the 1.8 V core supply to avoid latch-up. Use a supervisor IC or sequenced regulator pair; do not rely on diode-OR coupling. Decoupling must be sized to handle CPM DMA bursts during Ethernet packet reception without droop exceeding 5 percent.
コンプライアンス情報
Per the verified distributor data, MPC859DSLZP50A is RoHS compliant but contains lead per the lead-free-status field on DigiChip. Reach, halogen-free, and conflict-mineral status are not in the verified web data and are marked unknown. AEC-Q100 is not applicable because this is a commercial-grade CPE part.
