Texas Instruments

OPA541AP - 5A High-Power Op Amp | Texas Instruments

部品番号: OPA541AP ✓ 生産中
80 V (±40 V) Vdss 5 A Id TO-220-11 plastic power package Package
MOQ: 1 |

OPA541AP 概要

Texas Instruments OPA541AP is a high-power monolithic operational amplifier that operates from power supplies up to ±40 V and delivers continuous output currents up to 5 A. The device is supplied in an 11-pin TO-220 plastic power package and uses a proprietary bipolar and FET process to combine wide supply-voltage tolerance with high output-current capability. Its internal current-limit circuitry can be programmed with one external resistor to protect the amplifier and connected load during fault conditions.

A high-power operational amplifier is a specialized operational-amplifier category intended to drive low-impedance or high-current loads without an external power-output stage. Unlike a conventional low-power op amp, the OPA541AP includes internal power transistors and thermal management features. This places it in the amplifier-IC hierarchy and makes it suitable for audio transducers, laboratory amplifiers, motor-drive elements, and other power-buffering applications where load current and heat dissipation dominate the design.

The principal features include ±40 V maximum supply operation, 5 A continuous output current, and a 10 A peak-output capability. Programmable current limit is especially valuable because the limit threshold can be adjusted to suit a particular load, reducing the chance of excessive output current during overload or startup conditions. FET inputs support low input bias current, while the monolithic power-output stage reduces the external component count compared with a conventional op amp followed by discrete power transistors.

The OPA541AP is a single power operational amplifier rather than a precision signal-conditioning amplifier. Its bandwidth and slew-rate characteristics make it appropriate for audio and other wideband power-buffer applications, but it should not be selected where micropower operation, rail-to-rail input/output performance, or very low offset voltage is the primary requirement. Its operating range also makes rail-to-rail output capability unnecessary because the internal output stage can swing close to the supply rails under suitable load conditions.

Typical uses include direct drive of loudspeaker or other audio transducers, high-current laboratory output stages, industrial actuator interfaces, power buffers, and test-and-measurement equipment. In an audio design, the device can be placed in a power-amplifier topology after a voltage-gain stage, where its low-impedance output reduces the loading seen by the preceding amplifier. Its continuous-current rating should be checked against both the required load current and the thermal conditions at the intended operating temperature.

Thermal design is central to every OPA541AP implementation. Dissipation rises with output current, the difference between supply voltage and output voltage, and operating time; the power must be removed through the package tab and PCB copper or an external heatsink. Keep the current-limit resistor close to its programmed value, maintain generous copper area, and verify the worst-case junction temperature under sustained load rather than relying on short-duration current capability.

This page combines the manufacturer electrical characteristics with package, application, thermal, and drop-in replacement guidance. It also organizes the OPA541AP for engineers searching the datasheet, pinout, equivalent, replacement, audio-amplifier, current-limit, power-output, and high-current operational-amplifier requirements of a new design.

ドロップイン代替品: OPA541AP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: OPA541AP (同一形状・フットプリント) — 相違点: Package, Gain-Bandwidth Product, Mounting Type, Slew Rate, Supply Voltage Range.

Texas Instruments
Package: 5-lead TO-220 plastic package
Mounting Type: Through-hole power package with copper tab
Slew Rate: 8 V/µs
比較対象 OPA541AP →
Texas Instruments
Package: TO-220 (KVT), 7 pins
Gain-Bandwidth Product: 1 MHz
比較対象 OPA541AP →
Texas Instruments
Package: 7-lead TO-220
Gain-Bandwidth Product: 1 MHz
Mounting Type: Through-hole power package
比較対象 OPA541AP →
Texas Instruments
Package: TO-220 (KV), 11 pins
Gain-Bandwidth Product: 900 kHz
Slew Rate: 9 V/µs
比較対象 OPA541AP →
Texas Instruments
Package: SOIC-8 (D)
Gain-Bandwidth Product: 3 MHz
Mounting Type: Surface Mount

OPA543T

✅ ドロップイン ⚠️ 仕様未検証
📦 TO-220-11
Related 11-pin TO-220 high-power amplifier family; output-current and compensation characteristics differ, so verify the 5 A continuous and 10 A peak ratings against the required load.

📋 参考代替品(カタログ未掲載)

OPA544T

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 TO-220-11
Power operational amplifier · 4 A · 2 A · ±10 V to ±35 V · ±35 V · 8 V/µs · 100 pA maximum · Internal current limiting

価格はお問い合わせください

データシートを見る →

OPA547T

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 TO-220-11
High-voltage, high-current operational amplifier · 1 circuit · 60 V · ±30 V · 500 mA · 1 MHz · Yes · Yes

価格はお問い合わせください

データシートを見る →

OPA548T

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 TO-220-11
Single power operational amplifier · 1 circuit · 1 MHz · 10 V/µs · ±4 V to ±30 V · 7-lead TO-220 · 7 pins · Through-hole power package

価格はお問い合わせください

データシートを見る →

OPA549T

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 TO-220-11
High-voltage, high-current operational amplifier · 1 amplifier · 8 V to 60 V · 900 kHz · 9 V/µs · Excellent output swing · TO-220 (KV), 11 pins · Through-hole

価格はお問い合わせください

データシートを見る →

OPA541AP 最大定格&電気的特性

Amplifier Type Single power operational amplifier
Number of Channels 1 channel
Maximum Total Supply Voltage 80 V (±40 V)
Continuous Output Current 5 A
Peak Output Current 10 A
Current-Limit Configuration Programmable with one external resistor
Input Transistor Type FET input
Process Technology Proprietary bipolar and FET process
Gain-Bandwidth Product 1.6 MHz
Slew Rate 10 V/µs
Supply Voltage Range 20 V to 70 V
パッケージ TO-220-11 plastic power package
ピン数 11 pins
実装タイプ Through-hole

OPA541AP to-220-11 plastic power package ピン配置ガイド

OPA541AP (to-220-11 plastic power package パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

OPA541AP の to-220-11 plastic power package パッケージピン配置図

詳細なピン配置データはありません: OPA541AP.

詳細は データシート をご参照ください。

主な用途

OPA541AP の用途: 6 件s: High-Power Audio Amplifier, Laboratory Power Buffer, Industrial Actuator Driver, High-Current Sensor Conditioning, Motor and Solenoid Drive Interface, Test and Measurement Output Stage.

🎧

High-Power Audio Amplifier

The OPA541AP is suitable for the power-output stage of a high-current audio amplifier because it can deliver 5 A continuously and 10 A peak while operating from supplies up to ±40 V. Place it after a voltage-gain stage so the preceding amplifier drives only a high-impedance input while the OPA541AP supplies current to the loudspeaker network. The design must account for the changing impedance of an 8-ohm speaker, limit transient current, and remove heat through the TO-220 tab and copper area. Its 1.6 MHz gain-bandwidth product and 10 V/µs slew rate support wideband audio, while the 11-pin TO-220 package provides a practical high-power mechanical format.

🔧

Laboratory Power Buffer

The OPA541AP can serve as a laboratory output buffer when the driven instrument or test fixture requires substantially more current than a conventional operational amplifier can supply. Its 5 A continuous output-current capability helps isolate the source from low-impedance loads, while the FET-input stage avoids loading the driving signal source as heavily as a bipolar-input power stage. In this topology, the amplifier should operate within its feedback bandwidth and slew-rate limits, and the output stage needs protection against shorts. A current limit programmed with one resistor can bound fault current, while the package tab and a properly sized heatsink are essential when the load remains connected at elevated output power.

🏭

Industrial Actuator Driver

The OPA541AP can drive industrial actuator or transducer stages that exceed the current capability of ordinary op amps. Its ±40 V supply tolerance and 5 A continuous output allow it to serve as a high-current buffer when the actuator requires bipolar drive around ground. The feedback network should be designed for the load and signal bandwidth, while the current-limit resistor should be selected to protect both the output stage and actuator during stalled or shorted conditions. Because industrial environments can involve inductive loads, flyback paths and transient suppression must be evaluated separately; the OPA541AP's internal current limit alone does not replace an external energy-dissipation network.

🧩

High-Current Sensor Conditioning

The OPA541AP is useful in sensor-conditioning paths where the sensing element presents a low impedance and the measurement chain requires more output current than a conventional precision amplifier can provide. FET inputs reduce input-bias loading, while the monolithic output stage can drive the next stage with a lower output impedance. Designers should still select the gain, compensation, and bandwidth for the required signal rather than treating the power amplifier as a general-purpose precision op amp. Programmable current limiting helps protect a connected sensor during overload, and the TO-220 tab provides a direct path for heat removal. Calibration and measurement accuracy should therefore be verified with the actual source impedance and output load.

⚡

Motor and Solenoid Drive Interface

The OPA541AP can form the high-current interface between a low-level control signal and a motor winding, solenoid, or other electromechanical actuator. Its 5 A continuous current capability and resistor-programmable current limit are valuable for controlling fault current, while the bipolar output stage can swing around ground. The circuit must provide an appropriate flyback path for inductive energy and account for back electromotive force, which can exceed the nominal supply rails. Current-loop compensation and feedback placement are critical because the electrical load appears resistive at some frequencies and strongly inductive at others. The TO-220 package must be mounted to a heat-spreading copper region, and peak as well as continuous motor current must be checked.

🖥️

Test and Measurement Output Stage

The OPA541AP is appropriate for test and measurement equipment that drives resistive fixtures, transducers, or long cable loads from a low-impedance output stage. Its 5 A continuous output current and low-impedance FET-input power topology can reduce interaction between the signal generator and the load. The amplifier's 1.6 MHz gain-bandwidth product and 10 V/µs slew rate support many general-purpose audio and instrumentation waveforms, but waveform-dependent bandwidth must be checked at the selected gain. Output protection should prevent accidental shorts from exceeding safe current, while the current-limit resistor provides an additional adjustable protection function. Mechanical mounting and heatsinking are part of the electrical design because sustained loading can make the TO-220 tab the hottest component in the system.

おすすめ製品の概要

OPA445AP Voltage-gain stage preceding the power amplifier 使用用途: High-Power Audio Amplifier, Laboratory Power Buffer, High-Current Sensor Conditioning, Test and Measurement Output Stage OPA452 Related high-voltage operational-amplifier stage 使用用途: High-Power Audio Amplifier, Test and Measurement Output Stage OPA548T Texas Instruments 使用用途: Laboratory Power Buffer, Industrial Actuator Driver OPA544T Texas Instruments 使用用途: Industrial Actuator Driver INA149AIDR Texas Instruments 使用用途: High-Current Sensor Conditioning OPA549T Texas Instruments 使用用途: Motor and Solenoid Drive Interface OPA547T Texas Instruments 使用用途: Motor and Solenoid Drive Interface
What is the OPA541AP?
The OPA541AP is a single-channel, high-power monolithic operational amplifier designed to deliver up to 5 A continuously from supplies as high as ±40 V. According to the Texas Instruments OPA541 manufacturer datasheet, it uses a proprietary bipolar and FET process, includes FET inputs, and provides user-programmable current limiting through one external resistor. Its 11-pin TO-220 package is intended for through-hole, high-power audio and industrial applications rather than low-power precision signal conditioning.
What are the key specifications of OPA541AP that engineers should know?
The OPA541AP combines a ±40 V maximum supply range, 5 A continuous output current, 10 A peak output current, 1.6 MHz gain-bandwidth product, and 10 V/µs slew rate in an 11-pin TO-220 package. The Texas Instruments manufacturer datasheet also identifies FET inputs and single-resistor programmable current limiting. These characteristics place the device in the high-power operational-amplifier category and make continuous current, thermal dissipation, and load capability more important than micropower operation or precision offset performance.
Where can I download the OPA541AP datasheet PDF?
The official OPA541AP datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/opa541.pdf. The manufacturer datasheet contains the electrical characteristics, power-supply limits, current-limit programming information, package details, pin descriptions, and application guidance. Use this document for final circuit design because distributor summaries may omit limits or conditions that materially affect high-current operation.
Where can I find the OPA541AP pinout?
The OPA541AP pinout is found in the pin-configuration section of the Texas Instruments OPA541 manufacturer datasheet. The device uses an 11-pin TO-220 power package with connections for power supplies, input, output, current-limit programming, and ground or power-return functions. Confirm every connection against the package drawing before PCB layout because the exposed tab and high-current pins require deliberate copper routing and thermal design.
How much current can OPA541AP deliver continuously?
The OPA541AP can deliver 5 A of continuous output current and up to 10 A peak output current according to the Texas Instruments manufacturer datasheet. The device can operate from power supplies up to ±40 V, but allowable current also depends on supply voltage, output voltage, output waveform, load, ambient temperature, and package heat removal. The programmed current-limit threshold should be set below the safe load and amplifier limits.
How is the OPA541AP current limit programmed?
The OPA541AP current-limit threshold is programmed with a single external resistor connected to the current-limit programming terminal. According to the Texas Instruments manufacturer datasheet, this internal circuitry protects the amplifier and load during fault conditions. Select the resistor using the manufacturer relationship between resistance and limit current, then account for resistor tolerance, thermal drift, and the actual current needed by the load.
Is OPA541AP suitable as an audio power amplifier?
Yes, the OPA541AP is suitable for power-buffer and audio-amplifier stages because it provides 5 A continuous output current, a 1.6 MHz gain-bandwidth product, and a 10 V/µs slew rate. The Texas Instruments manufacturer datasheet identifies high-power audio applications as a primary use case. Its 11-pin TO-220 package requires substantial heat sinking, and the chosen gain, supply rails, output filter, and protection network must suit the loudspeaker impedance and required output power.
What can replace OPA541AP?
The closest same-family drop-in candidates are the Texas Instruments OPA543T, OPA544T, OPA547T, OPA548T, and OPA549T in compatible 11-pin TO-220 configurations. Each offers a related high-power monolithic operational-amplifier function, but current rating, current-limit implementation, supply limits, and package details differ. Verify the selected replacement against the manufacturer datasheet and the original PCB footprint before substituting it.
What is the best cross-brand equivalent for OPA541AP?
No cross-brand drop-in equivalent is established by the available manufacturer and cross-reference information for the OPA541AP. The OPA541's combination of ±40 V supplies, 5 A continuous output, programmable current limit, FET inputs, and an 11-pin TO-220 footprint makes an unqualified substitute risky. The closest candidates identified for comparison are Texas Instruments OPA541 family devices; a different manufacturer should be used only after its pinout, current limit, thermal limits, and transient response are verified.
OPA541AP versus OPA548T — which is better for a high-current amplifier?
OPA541AP versus OPA548T depends mainly on current capability, current-limit behavior, and application requirements rather than a guaranteed universal substitute. The OPA541AP is specified for 5 A continuous and 10 A peak output with programmable current limiting, while OPA548T belongs to the related high-power OPA amplifier family. Use the Texas Instruments OPA541 manufacturer datasheet and the OPA548T datasheet to compare output-stage limits, supply range, thermal performance, and pin functions before redesigning or replacing the original stage.
When should I choose OPA541AP over OPA549T?
Choose OPA541AP when a design specifically targets its 5 A continuous-output device, FET-input stage, and resistor-programmable current limit. Consider OPA549T only after comparing its manufacturer specifications with the load, because it belongs to the related high-power operational-amplifier family but is not proven identical to the OPA541AP. The final choice should consider sustained current, peak current, thermal dissipation, supply range, output swing, and exact PCB compatibility.
Is OPA541AP suitable for driving an 8-ohm loudspeaker?
The OPA541AP can be used in an audio power stage that drives an 8-ohm loudspeaker when the amplifier topology, supply voltage, gain, and cooling satisfy the required output power and current. According to the Texas Instruments manufacturer datasheet, the device supports 5 A continuous output and 10 A peak output. Real loudspeakers have impedance variation, so use the minimum impedance, reactive behavior, crossover frequency, and amplifier thermal limits when sizing the output stage.
How much thermal dissipation should I design for with OPA541AP?
Thermal dissipation must be calculated from the actual output waveform, supply voltage, output voltage, current, and ambient temperature. Estimated: with 35 V across the output stage and 5 A flowing continuously, the ideal output-stage dissipation is 175 W before subtracting output power delivered to the load. Actual device dissipation is lower than the ideal stage loss, but it can still require a substantial heatsink and copper area; confirm the final value with the manufacturer dissipation model and PCB thermal data.
Where can I buy OPA541AP and check its current lead time?
Request a quote for OPA541AP through the Request a Quote form on this page to obtain current commercial terms, availability, and lead-time confirmation for the exact OPA541AP ordering code. The part is a Texas Instruments high-power operational amplifier in an 11-pin TO-220 package, and the manufacturer datasheet identifies the supported electrical configuration. Include your target quantity, packaging requirements, date code policy, and destination country when requesting the quotation.
Is OPA541AP in stock and what is its price?
Current OPA541AP stock and transactional terms should be confirmed through the Request a Quote form on this page because availability can change with quantity and supply conditions. Provide the exact OPA541AP MPN, required quantity, and acceptable lead time so the quotation can be matched to the requested production schedule. The manufacturer lists the OPA541 family on its official product page, while exact package, grade, and delivery conditions should be confirmed during procurement.

エンジニアリング参考データ: OPA541AP — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose OPA541AP when the design requires a single, high-current operational amplifier with a 5 A continuous rating, 10 A peak capability, FET inputs, adjustable current limiting, and an 11-pin TO-220 footprint. It is particularly suitable for audio power stages, laboratory buffers, actuator interfaces, and other loads where the output stage must dissipate substantial heat. OPA543T, OPA544T, OPA547T, OPA548T, and OPA549T are same-family alternatives with related TO-220 formats, but each must be selected according to its own current rating, supply limits, current-limit implementation, compensation options, and thermal behavior. Prefer OPA541AP when its established 5 A continuous-output specification and programmable limit match the design most closely. Use another OPA541-family member when its distinct output-current, bandwidth, or fault-response characteristics are better suited to the load. No cross-brand drop-in replacement should be selected solely from a generic functional-equivalent listing; verify the exact pin functions and protection circuitry against the original PCB.

代替品との比較

パラメータ この製品 OPA543T OPA544T OPA547T OPA548T OPA549T
Package TO-220-11 TO-220-11 TO-220-11 TO-220-11 TO-220-11 TO-220-11
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Type Single high-power monolithic operational amplifier Single high-power monolithic operational amplifier Single high-power monolithic operational amplifier Single high-power monolithic operational amplifier Single high-power monolithic operational amplifier Single high-power monolithic operational amplifier

主な差別化要因

  • High continuous output current (vs OPA544T)
  • Single-resistor current-limit programming (vs OPA543T)
  • Wide bipolar supply capability (vs OPA548T)
  • FET-input power stage (vs OPA549T)

設計ノート

Design the TO-220 heat path before committing to the load. Estimated: with 35 V across the output stage and 5 A flowing continuously, the ideal stage loss is 175 W; actual device dissipation must be calculated from output power and supply conditions. Use the package tab, substantial PCB copper, and an appropriately sized heatsink, then verify junction temperature under worst-case ambient temperature and sustained load.

Program the current limit below both the amplifier's safe continuous current and the load's fault current. Include resistor tolerance and thermal coefficient when selecting the current-limit resistor. This protection complements, rather than replaces, correctly rated supply wiring, output protection, and thermal design, especially when driving reactive loudspeakers, solenoids, motors, or long cables.

Place the current-limit resistor and compensation or feedback components close to their associated amplifier pins, and use separate input and output routing to avoid feeding output current into the input reference. The power-supply and output paths require wide copper traces, multiple vias where appropriate, and a low-impedance return connection to the package tab or designated power-return connection.

Do not treat the 10 A peak-current capability as a continuous rating. Confirm output swing, bandwidth at the selected closed-loop gain, supply limits, and the load's reactive behavior. The manufacturer datasheet notes that the OPA541 uses a proprietary bipolar and FET process and supports resistor-programmable current limiting, but operating outside those conditions can trigger protection or thermal shutdown.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The OPA541 manufacturer datasheet and official product page do not provide an explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement for the OPA541AP ordering code in the available material.

関連検索

OPA541AP datasheet OPA541AP audio amplifier OPA541AP datasheet PDF OPA541AP pinout OPA541AP TO-220-11 OPA541AP equivalent OPA541AP replacement OPA541AP current limit resistor OPA541AP 5A output current OPA541AP ±40V power amplifier OPA541AP price OPA541AP stock

関連部品&用語

Texas Instruments OPA541AP OPA541 OPA543T OPA544T OPA547T OPA548T OPA549T high-power operational amplifier power operational amplifier monolithic operational amplifier amplifier IC semiconductor TO-220-11 TO-220 package family through-hole package FET input bipolar and FET process programmable current limit continuous output current peak output current gain-bandwidth product slew rate audio power amplifier Texas Instruments OPA541 manufacturer datasheet
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示