PIC12F509-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz INTOSC, 8-DFN | Microchip
部品番号: PIC12F509-I/MC ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.04 | $1.04 |
| 10 | $0.94 | $9.40 |
| 100 | $0.84 | $84.00 |
| 500 | $0.74 | $370.00 |
| 1,000 | $0.65 | $650.00 |
| 3,000 | $0.55 | $1,650.00 |
PIC12F509-I/MC 概要
An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip built around an 8-bit data path, integrating a CPU, program memory (ROM/Flash), data memory (RAM), and peripherals such as timers, ADC, and GPIO into a single IC. 8-bit MCUs sit within the microcontroller hierarchy as embedded controllers -> microcontrollers -> microcomputer family -> integrated circuits -> semiconductors, occupying the low-cost, low-power end of the MCU spectrum versus 16-bit and 32-bit alternatives. They are best suited for cost-sensitive applications where software complexity and processing throughput remain modest.
Key features of the PIC12F509 include 33 single-word instructions at 1 microsecond instruction cycle, an internal 4 MHz oscillator with 6 I/O pins (5 bidirectional, 1 input-only), a Watchdog Timer with on-chip RC oscillator for reliable operation, and In-Circuit Serial Programming (ICSP) for field-upgradeable firmware. The device supports power-managed modes including Sleep and wake-on-pin-change for ultra-low standby power consumption.
The PIC12F509 architecture uses a Harvard RISC core with separate program and data buses, a 12-bit wide instruction word, and a hardware stack that simplifies subroutine handling. Its 6 I/O pins include GP0-GP5 with multi-function capability (digital I/O, comparator input, timer I/O), one 8-bit timer/counter (TMR0) with 8-bit prescaler, and an integrated analog comparator. With 1.5KB Flash, it targets code sizes up to roughly 1000 instructions typical.
Typical applications include battery-powered consumer products, LED drivers, simple motor control, sensor signal conditioning, and any small-form-factor embedded control where the 8-DFN footprint saves board space. The 8-pin DFN package makes it ideal for ultra-compact designs including wearables, IoT edge nodes, and smart sensors.
When designing with the PIC12F509, note that only 5 of 6 I/O pins are fully bidirectional; GP3 is input-only. For applications requiring more I/O, consider PIC16F15313 (recommended upgrade). The internal 4 MHz oscillator can drift with temperature - for precision timing use an external crystal or the PIC12F1840 variant.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing the engineering context needed for sourcing and board-level design decisions.
ドロップイン代替品: PIC12F509-I/MC — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC12F509-I/MC （同一形状・フットプリント） — 相違点: Package, Timers, Watchdog Timer, Internal Oscillator, Instruction Set.
クイック比較ツール — 並列比較する代替部品を選択:
PIC12F509-E/MC
✅ ドロップイン✓ 在庫あり
$0.5 / 個
データシートを見る →PIC12F508-I/MC
✅ ドロップイン✓ 在庫あり
$0.47 / 個
データシートを見る →PIC12F508-E/MC
✅ ドロップイン✓ 在庫あり
$0.55 / 個
データシートを見る →PIC10F200-I/MC
✅ ドロップイン✓ 在庫あり
$0.42 / 個
データシートを見る →PIC12F509-I/MC 最大定格＆電気的特性
| Architecture | 8-bit RISC Harvard |
| Instruction Set | 33 single-word/single-cycle instructions |
| Program Memory (Flash) | 1.5 KB (1K x 12) |
| RAM | 41 bytes |
| Data EEPROM | Not available (Flash-based device) |
| Maximum CPU Speed | 4 MHz |
| Instruction Cycle Time | 1 microsecond at 4 MHz |
| Internal Oscillator | 4 MHz INTOSC |
| Supply Voltage Range | 2.0 V to 5.5 V |
| I/O Pins | 6 (GP0-GP5; GP3 input-only) |
| Timers | 1 x 8-bit (TMR0 with 8-bit prescaler) |
| Analog Comparator | Yes (1 module) |
| Watchdog Timer | Yes (WDT with on-chip RC) |
| In-Circuit Serial Programming | Yes (ICSP) |
| 動作温度 | -40 C to +85 C (industrial) |
| パッケージ | 8-pin DFN (2 mm x 3 mm) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
PIC12F509-I/MC ピン構成
| ピン 1 | GP3/MCLR/VPP — General purpose I/O pin 3 / Master Clear reset / Programming voltage; weakly pulled-up internally |
| ピン 2 | GP0 — Bidirectional digital I/O pin 0; can be analog comparator output |
| ピン 3 | GP1 — Bidirectional digital I/O pin 1; can be analog comparator negative input |
| ピン 4 | GP2 — Bidirectional digital I/O pin 2; TMR0 clock input; can be analog comparator positive input |
| ピン 5 | GP4/OSC2 — Bidirectional digital I/O pin 4 / oscillator output for crystal mode |
| ピン 6 | GP5/OSC1/CLKIN — Bidirectional digital I/O pin 5 / oscillator input / external clock input |
| ピン 7 | VSS — Ground reference |
| ピン 8 | VDD — Positive supply voltage 2.0V to 5.5V |
主な用途
PIC12F509-I/MC の用途: 7 件s: Battery-Powered Consumer Products, LED Lighting Controllers, Simple Sensor Signal Conditioning, Compact IoT Edge Nodes, Small Motor and Solenoid Drivers, Replacement for Legacy 12C509 Designs, Educational and Hobby Projects.
Battery-Powered Consumer Products
The PIC12F509-I/MC fits battery-powered consumer products because its 2.0V to 5.5V supply range and 4 MHz internal oscillator draw minimal quiescent current from a single lithium coin cell. The 8-DFN package measures only 2x3 mm, enabling integration inside compact form factors like smart wearables and Bluetooth beacons where board area is at a premium. With 1.5KB Flash it can run simple state machines for push-button input, LED blinking, and Sleep/wake-on-change cycles extending battery life. Designers can pair it with a sensor front-end and use the integrated analog comparator for threshold detection without additional components.
おすすめ
LED Lighting Controllers
The PIC12F509-I/MC is well suited for LED lighting controllers because its 6 I/O pins can drive multi-channel PWM-like patterns or simple on/off sequencing for decorative or indicator LEDs. The 4 MHz instruction cycle and 1 microsecond resolution allow flicker-free dimming algorithms using the 8-bit TMR0 timer and software PWM loops. With 41 bytes of RAM the chip can hold pattern buffers and color variables for RGB lighting nodes. Sleep current is low enough for solar-powered garden lights, and the 2.0V to 5.5V supply range handles Li-Ion, 2xAA, and USB 5V rails without additional regulation.
おすすめ
Simple Sensor Signal Conditioning
The PIC12F509-I/MC fits simple sensor signal conditioning designs where the on-chip analog comparator replaces a discrete op-amp threshold circuit. Its 1 microsecond instruction cycle is fast enough to debounce mechanical sensors, implement RC-time sensor measurement, or count pulses from a tachometer input. The 1.5KB Flash accommodates look-up tables for linearization of thermistor or NTC sensor curves. The 8-pin DFN package lets the MCU sit directly behind the sensor on the same PCB, minimizing noise pickup. For designs needing ADC, upgrade to PIC12F1571 or PIC12F1840.
おすすめ
Compact IoT Edge Nodes
The PIC12F509-I/MC serves well as a small microcontroller companion in compact IoT edge nodes where a wireless module handles connectivity and the PIC handles simple local logic. With 6 I/O pins, it can read digital inputs, drive outputs, monitor a push-button, and manage Sleep modes between transmissions. The 4 MHz internal oscillator eliminates the need for external crystal components, reducing BOM cost. Sleep mode current is low enough for coin-cell-powered edge sensors. For designs needing ADC to read battery voltage, upgrade to PIC12F1840 with 10-bit ADC.
おすすめ
Small Motor and Solenoid Drivers
The PIC12F509-I/MC is suitable for small DC motor or solenoid control where the MCU generates timing sequences and direction control signals for external drivers. Its 6 I/O pins can interface with H-bridge enable inputs, MOSFET gate drivers, or relay coils. The 4 MHz clock and 8-bit TMR0 with prescaler permit precise timing for stepper motor acceleration ramps. With 1.5KB Flash and 41 bytes RAM, it can store motion profiles and run simple closed-loop PWM control via the analog comparator for current sensing feedback. The 8-DFN package fits inside miniature robotics and hobby servo controllers.
おすすめ
Replacement for Legacy 12C509 Designs
The PIC12F509-I/MC is the modern Flash replacement for older EPROM-based PIC12C509 designs, providing in-circuit programmability via ICSP without UV erase. It is pin-compatible with legacy PIC12C509A and PIC12C508A DIP and SOIC footprints when using the -I/P or -I/SN variants. Designers can migrate existing 12C code to 12F with minimal firmware changes since the 33-instruction RISC core is identical. The 8-DFN package suits new miniaturized upgrades where legacy designs used PDIP. This makes it an ideal refresh component for extending the production life of proven designs.
おすすめ
Educational and Hobby Projects
The PIC12F509-I/MC is a popular choice for educational and hobby projects because the 8-pin PIC architecture is the simplest entry point into the Microchip PIC ecosystem. With only 33 single-cycle instructions to learn, students can master embedded programming basics on a 2.0V to 5.5V supply using the free MPLAB X IDE and PICKit programmer. The 8-DFN package is challenging for hand-soldering, so the DIP variant PIC12F509-I/P is recommended for breadboard prototypes. Projects include blinky LEDs, push-button counters, simple games, and basic sensor readers.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC12F509-I/MC — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC12F509-I/MS | PIC12F509-E/MC | PIC12F508-I/MC | PIC12F508-E/MC | PIC10F200-I/MC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | DFN-8 (2x3 mm) | MSOP-8 - different PCB land pattern | DFN-8 (2x3 mm) - same | DFN-8 (2x3 mm) - same | DFN-8 (2x3 mm) - same | DFN-8 (2x3 mm) - same |
| Flash Memory | 1.5 KB | 1.5 KB (same) | 1.5 KB (same) | 0.75 KB (-50%) | 0.75 KB (-50%) | 0.375 KB (-75%) |
| RAM | 41 bytes | 41 bytes (same) | 41 bytes (same) | 25 bytes (-39%) | 25 bytes (-39%) | 16 bytes (-61%) |
| Maximum CPU Speed | 4 MHz | 4 MHz (same) | 4 MHz (same) | 4 MHz (same) | 4 MHz (same) | 4 MHz (same) |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C (same) | -40C to +125C (extended) | -40C to +85C (same) | -40C to +125C (extended) | -40C to +85C (same) |
| Analog Comparator | Yes (1 module) | Yes (same) | Yes (same) | Yes (same) | Yes (same) | No |
| ADC | Not available | Not available | Not available | Not available | Not available | Not available |
| I/O Pins | 6 (GP3 input-only) | 6 (same) | 6 (same) | 6 (same) | 6 (same) | 4 (different) |
| ICSP Programming | Yes | Yes (same) | Yes (same) | Yes (same) | Yes (same) | Yes (same) |
| Approximate Unit Price (qty 1000) | $0.65 | $0.70 (slight premium for MSOP) | $0.75 (extended temp premium) | $0.55 (smaller Flash) | $0.65 | $0.45 (lowest cost) |
主な差別化要因
- Extended temperature variant available in same DFN-8 footprint （vs PIC12F509-E/MC)
- Drop-in Flash downgrade path to PIC12F508 same package （vs PIC12F508-I/MC)
- Maintains compatibility with 33-instruction RISC core across 12F family （vs PIC12F1840)
設計ノート
Pin GP3 on the PIC12F509 is input-only - do NOT wire it to an output-driving peripheral. GP3 also doubles as the MCLR/VPP reset and programming pin, so leaving it floating can cause spurious resets in noisy environments. Always connect GP3/MCLR to VDD through a 10k ohm pull-up resistor (the internal weak pull-up is often insufficient for reliable operation in electrically noisy industrial environments). Per Microchip datasheet 41136E, the MCLR pin must not exceed VDD + 0.3V to avoid latch-up.
The 8-pin DFN package has an exposed thermal pad (EP) on the underside that should be soldered to a PCB land pattern for mechanical reliability and thermal dissipation. Per IPC-7351 nomenclature, the DFN-8 land pattern uses 0.6 mm pitch pads with center exposed pad approximately 1.0 mm x 2.0 mm. The DFN package is challenging to hand-solder - use hot air rework or reflow oven. For breadboard prototypes, choose the PDIP variant PIC12F509-I/P instead, which shares the same die.
Place a 0.1 microfarat ceramic decoupling capacitor as close as possible to the VDD pin (pin 8) with a short trace to VSS (pin 7). For designs with switching loads or RF modules, add a 10 microfarad bulk capacitor on the VDD rail near the MCU. The internal 4 MHz oscillator drift is typically +/-2% over the full -40C to +85C industrial temperature range - acceptable for UART or low-precision timing but not for USB or precision measurement.
When using the internal 4 MHz oscillator (INTOSC), leave GP4 and GP5 as general-purpose I/O. If switching to external crystal mode (XT, LP, or HS), GP5 becomes OSC1 input and GP4 becomes OSC2 output - firmware must configure the OSCCON register appropriately. Route crystal traces short and symmetric with ground guard rings to minimize EMI. Per Microchip AN588, keep crystal traces under 5 mm when possible.
The PIC12F509-I/MC dissipates negligible power (typically 1-2 mA active at 4 MHz, microamps in Sleep mode) and does not require heatsinking. Estimated power: at VDD=5V and 4 MHz, typical active current is ~1.1 mA and Sleep current is ~100 nA - well within DFN-8 thermal limits of theta_JA approximately 50 C/W on a standard JEDEC 4-layer test board. For battery-life calculations, use the Sleep current figure of 100 nA as the dominant contributor when the device wakes only on interrupts.
コンプライアンス情報
RoHS compliant per Microchip product page. Lead-free DFN package. Not AEC-Q100 qualified - for automotive applications consider PIC12F509-E/MC with extended temperature range, though it is also not formally AEC-Q100 qualified.
