PIC16F883-E/ML - 20MHz 8-Bit Flash MCU | Microchip Technology
部品番号: PIC16F883-E/ML ✓ 生産中PIC16F883-E/ML 概要
A PIC microcontroller is an 8-bit embedded-control IC that integrates a processor core, Flash program memory, data memory, EEPROM, I/O ports, and peripherals into one device. PIC16F883 belongs to the PIC16 family, a broad microcontroller platform used for industrial control, instrumentation, consumer products, and small embedded systems. Its architecture uses a compact instruction set and a unified programming environment, allowing control logic, sensor acquisition, and output switching to be handled in one inexpensive component.
The PIC16F883-E/ML includes 7 KB of Flash program memory, 256 bytes of EEPROM data memory according to the manufacturer product description, self-programming, and a 20 MHz maximum clock speed. The peripheral set includes two comparators, 11 channels of 10-bit analog-to-digital conversion, and capture, compare, and PWM functions. These resources allow the MCU to monitor analog inputs, generate timing signals, control actuators, and implement embedded control logic without requiring a separate analog converter or timer IC.
The device uses the PIC16 enhanced Flash architecture and is described by Microchip as having only 35 single-word instructions. Self-programming allows firmware to be updated in the field, while EEPROM provides nonvolatile storage for calibration constants, configuration values, counters, and diagnostic records. The 25 available I/O pins support digital interfaces, control signals, and peripheral multiplexing in compact embedded products.
Typical applications include industrial sensor nodes, temperature controllers, motor and relay control boards, power-supply monitoring, instrumentation front ends, LED lighting controllers, and compact consumer equipment. The 10-bit ADC is particularly useful for monitoring potentiometers, resistive sensors, dividers, and analog supply rails, while the PWM-capable peripherals simplify dimming, actuator drive, and periodic waveform generation.
Designers should preserve the exposed-pad thermal and electrical requirements of the QFN package, place decoupling capacitors close to the supply pins, and follow the manufacturer pin-description table when assigning analog and digital functions. Firmware should also account for the device’s 10-bit ADC resolution, peripheral multiplexing, and the operating limits specified in the PIC16F883 datasheet.
This product page combines the manufacturer’s device description with distributor package and ordering information, focused engineering guidance, and practical application context. It helps engineers identify the correct 28-QFN variant, plan programming and decoupling, and assess the PIC16F883-E/ML for compact embedded-control designs.
ドロップイン代替品: PIC16F883-E/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC16F883-E/ML (同一形状・フットプリント) — 相違点: ADC, Package, Timers, Program Memory (Flash), Operating Temperature.
PIC16F883-I/ML
✅ ドロップイン価格はお問い合わせください
データシートを見る →PIC16F883T-I/ML
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →PIC16F882-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
PIC16F886-I/ML
✅ ドロップイン価格はお問い合わせください
データシートを見る →PIC16F887-I/ML
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →PIC16F883-E/ML 最大定格&電気的特性
| Product Type | 8-bit CMOS Flash PIC microcontroller |
| 最大クロック周波数 | 20 MHz |
| Program Memory | 7 KB (4K x 14) |
| Data Memory | 256 bytes |
| EEPROM Data Memory | 256 bytes |
| Supply Voltage Range | 2.5 V to 5 V |
| Number of I/O Pins | 25 |
| パッケージ | 28-pin QFN (6x6 mm) with exposed pad |
| Architecture | PIC 8-bit RISC core |
| Instruction Set | 35 single-word instructions |
| Self-Programming | Supported |
| Comparator Count | 2 |
| ADC Resolution | 10 bit |
| ADC Channels | 11 |
| Capture/Compare/PWM Resources | 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM |
| Programming and Debug Support | In-circuit programming and ICD support |
PIC16F883-E/ML 28-pin qfn (6x6 mm) with exposed pad ピン配置ガイド
PIC16F883-E/ML (28-pin qfn (6x6 mm) with exposed pad パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: PIC16F883-E/ML.
詳細は データシート をご参照ください。
主な用途
PIC16F883-E/ML の用途: 6 件s: Industrial Sensor Monitoring, Temperature and Process Control, Motor and Relay Control, Power-Supply Monitoring, Instrumentation Front End, LED Lighting Controller.
Industrial Sensor Monitoring
The PIC16F883-E/ML fits compact industrial sensor nodes because its 11-channel, 10-bit ADC can acquire analog inputs while the 20 MHz processor handles filtering, threshold decisions, and control logic. The 256-byte EEPROM preserves calibration values and counters without repeated writes to Flash. With 25 I/O pins, the device can connect digital sensors, status indicators, and an actuator while operating from a 2.5 V, 3.3 V, or 5 V rail. The main design consideration is providing clean analog and digital grounds, decoupling the supply pins, and verifying sensor signals remain within the ADC input limits.
おすすめ
Temperature and Process Control
The PIC16F883-E/ML is appropriate for temperature controllers because its 10-bit ADC provides enough resolution for many resistive sensors, while the capture, compare, and PWM resources can drive heaters, cooling outputs, or alarm indicators. Self-programming supports field firmware updates, and EEPROM can retain setpoints or calibration coefficients. The MCU’s 7 KB Flash capacity allows control algorithms, filtering, fault handling, and communications to coexist in one device. Designers should compensate sensor nonlinearity, verify control-loop timing, and use suitable isolation where the monitored process exceeds the electrical environment of the controller.
おすすめ
Motor and Relay Control
The PIC16F883-E/ML can coordinate relays, solenoids, and small motors where deterministic timing and multiple digital outputs are required. Its PWM-capable peripherals simplify pulse generation, while the 25 I/O pins provide control for direction signals, feedback inputs, and interlocks. The 20 MHz clock supports responsive debouncing and closed-loop sequencing, and the 256-byte EEPROM can store operating counters or configuration records. A production design should include driver transistors, flyback protection for inductive loads, current limiting, and isolation between the MCU and noisy power stages.
おすすめ
Power-Supply Monitoring
The PIC16F883-E/ML is useful in power-supply monitoring modules because its ADC can supervise scaled voltage rails, current-sense outputs, and temperature signals while the processor evaluates limits and updates status indicators. The 2.5 V to 5 V operating range supports regulated control electronics, and self-programming enables field adjustment of thresholds or event logging. EEPROM can retain fault counters and operating history across power cycles. For accurate measurements, use a defined divider or amplifier, account for ADC error and settling behavior, and keep high-current switching paths physically separated from the analog measurement section.
おすすめ
Instrumentation Front End
The PIC16F883-E/ML can serve as the control and measurement processor in compact instrumentation, combining analog sampling, digital calibration, display control, and data storage in one package. The 11-channel 10-bit ADC supports multiple sensor inputs, and the 25 I/O pins can serve panel controls or communication lines. Its 7 KB Flash memory accommodates acquisition routines and communication firmware, while EEPROM stores calibration constants. For laboratory-grade accuracy, use precision references and suitable signal conditioning; the MCU’s ADC should not be treated as a substitute for a dedicated high-resolution converter when measurement performance requires greater precision or speed.
おすすめ
LED Lighting Controller
The PIC16F883-E/ML suits LED lighting modules and dimming controllers because its PWM resources can generate adjustable drive waveforms and its 11-channel ADC can monitor current or temperature feedback. The 20 MHz processor leaves headroom for lighting effects, button handling, and fault reporting, while 25 I/O pins support multiple channels and status signals. EEPROM is useful for storing brightness scenes or configuration data across power cycles. The design must match the LED driver topology to the MCU supply voltage and use transistor drive, current limiting, and thermal protection appropriate to the LED load.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC16F883-E/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC16F883-I/ML | PIC16F883T-I/ML | PIC16F882-I/ML | PIC16F886-I/ML | PIC16F887-I/ML |
|---|---|---|---|---|---|---|
| Package | 28-pin QFN (6x6 mm) with exposed pad | 28-pin QFN (6x6 mm) with exposed pad | 28-pin QFN (6x6 mm) with exposed pad | 28-pin QFN (6x6 mm) with exposed pad | 28-pin QFN (6x6 mm) with exposed pad | 28-pin QFN (6x6 mm) with exposed pad |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Product Type | 8-bit CMOS Flash PIC microcontroller | 8-bit CMOS Flash PIC microcontroller | 8-bit CMOS Flash PIC microcontroller | PIC16 8-bit Flash microcontroller | PIC16 8-bit Flash microcontroller | PIC16 8-bit Flash microcontroller |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Temperature Grade | -E extended-temperature grade | -I industrial-temperature grade | -I industrial-temperature grade | -I industrial-temperature grade | -I industrial-temperature grade | -I industrial-temperature grade |
主な差別化要因
- Broader embedded peripheral set in the PIC16F883 (vs PIC16F882-I/ML)
- Direct same-device alternative with a different temperature grade (vs PIC16F883-I/ML)
- Program memory and Flash self-programming support (vs PIC16F882-I/ML)
設計ノート
Treat the QFN exposed pad as both a thermal path and a required electrical connection according to the manufacturer datasheet. Provide an uninterrupted ground or thermal-pad land pattern with short vias into the ground plane, and maximize nearby copper without violating board-clearance rules. Check the exposed-pad copper area and via current capacity against the dissipation required by the application. Estimated: with 7.0 W dissipation and a 35 C/W junction-to-ambient value, the junction-temperature rise would be 245 C, so a thermal estimate must be performed for high-duty-cycle switching loads.
Place input bypass capacitors directly between each supply pin and the nearest ground reference, with very short traces and low-inductance vias. Keep analog sensor routing away from PWM outputs, relay drivers, and switching-node traces. The 10-bit ADC will be sensitive to ground bounce and supply ripple, so use a stable analog reference, continuous ground routing beneath the QFN, and separate analog and digital return paths where the board architecture permits.
Do not substitute a 28-pin MCU solely because the lead count matches. Verify the package drawing, exposed-pad requirements, pin names, ADC channels, comparator assignments, timer resources, Flash size, RAM, EEPROM, and voltage limits. Also check the temperature-grade code before changing between -E and -I options. The Microchip pin and code compatibility chart is the appropriate starting point, followed by a complete review of the target device datasheet.
Decouple the MCU supply locally and ensure the regulator can support both average current and startup transients from its digital and analog peripherals. Use brownout and reset behavior appropriate to the application so partially initialized firmware cannot drive external equipment. If the MCU controls power stages, define a safe reset state and use pull resistors to keep external control lines inactive while the device is reset or unpowered.
コンプライアンス情報
The manufacturer describes the PIC16F883 as an active PIC16 8-bit microcontroller. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not identified for this exact orderable part.