RTAX2000S-1CQ256PROTO - 2M-Gate Rad-Tolerant FPGA Proto | Microchip
部品番号: RTAX2000S-1CQ256PROTO ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1995 | $1,995.00 |
| 2 | $1895 | $3,790.00 |
| 5 | $1795 | $8,975.00 |
| 10 | $1695 | $16,950.00 |
| 25 | $1595 | $39,875.00 |
RTAX2000S-1CQ256PROTO 概要
A radiation-tolerant FPGA is a programmable logic device qualified for space-flight environments, where high-energy particles cause single-event upsets (SEU) and total ionizing dose (TID) degradation. Within the power-management hierarchy of spacecraft avionics, these devices sit above general-purpose FPGAs in reliability and are the direct descendants of the commercial Microsemi (Actel) Axcelerator architecture, retaining library compatibility with it.
Key features of the RTAX2000S family include nonvolatile, highly reliable antifuse technology that is live-at-power-up (no configuration flash or external boot device), up to 540 kbits of embedded SRAM with optional EDAC protection, and SEU-hardened registers that reduce or eliminate the need for triple-module redundancy (TMR). The family is specified for total dose of 300 krad (functional) and 200 krad (parametric), with SEU rates below 1E-10 errors per bit-day on flight-grade variants.
Architecturally, the RTAX2000S is based on the Axcelerator fabric: fine-grained logic modules, segmentable clock resources, chip-wide routing, and embedded FIFO control logic. Note that although RTAX-S devices are library-compatible with Axcelerator, internal timing differs significantly, which is exactly why Microchip application note AC170 recommends prototyping on devices such as this PROTO unit and the companion Aldec ACT-H3Ki-CQ256 reprogrammable adaptor before flight-device programming.
Typical applications include satellite payload data processing, spacecraft attitude control and telemetry interfaces, radiation-heavy orbital and deep-space missions, and high-reliability defense electronics. The 2M-gate density accommodates bus controllers, image preprocessing pipelines, and glueless interfaces to space-grade memories.
A key design consideration: PROTO units are intended for engineering validation, not space flight; order the corresponding flight suffix (V/B/E variants) for qualification hardware.
This page adds value beyond the manufacturer datasheet by consolidating distributor availability, drop-in same-package alternatives, prototyping-workflow guidance, and procurement FAQs for this hard-to-source aerospace component.
ドロップイン代替品: RTAX2000S-1CQ256PROTO — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: RTAX2000S-1CQ256PROTO （同一形状・フットプリント） — 相違点: Package, Configuration, Radiation Tolerance, Technology, Embedded Memory.
クイック比較ツール — 並列比較する代替部品を選択:
RTAX2000SL-1CQ256PROTO
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →RTAX2000SL-1CQ256V
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →RTAX2000S-1CQ256PROTO 最大定格＆電気的特性
| Logic Blocks (CLBs) | 21504 |
| Equivalent System Gates | 2000000 |
| Additional ASIC Gates | 250000 |
| Embedded Memory | up to 540 kbits with optional EDAC |
| Technology | Antifuse (nonvolatile, OTP), CMOS |
| SEU Rate | less than 1E-10 errors per bit-day (family spec) |
| Total Ionizing Dose (Functional) | 300 krad |
| Total Ionizing Dose (Parametric) | 200 krad |
| パッケージ | CQ256 ceramic quad package, 256 pins |
| 実装タイプ | Surface Mount |
| Logic Family | CMOS |
| Maximum User I/Os (family) | up to 684 (density dependent) |
| Architecture Base | Axcelerator compatible fabric |
| Configuration | Live at power-up, no external boot device |
| Product Grade | PROTO - engineering prototyping unit |
RTAX2000S-1CQ256PROTO cq256 ceramic quad package, 256 pins ピン配置ガイド
RTAX2000S-1CQ256PROTO (cq256 ceramic quad package, 256 pins パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: RTAX2000S-1CQ256PROTO.
詳細は データシート をご参照ください。
主な用途
RTAX2000S-1CQ256PROTO の用途: 6 件s: Satellite Payload Data Processing, Spacecraft Attitude Control and Avionics, Deep-Space Mission Electronics, Defense and High-Reliability Ground Systems, FPGA Design Verification and Emulation, Telemetry, Tracking and Command (TT&C) Units.
Satellite Payload Data Processing
The RTAX2000S-1CQ256PROTO is used during the development of satellite payload processing boards, where its 2,000,000 equivalent gates and 21,504 CLBs provide enough capacity for image preprocessing, packet formatting, and high-rate data pipelines. The antifuse fabric is live at power-up, eliminating configuration-boot vulnerabilities on orbit. In the prototyping phase, engineers validate RTL, pin assignments, and I/O timing on the CQ256 footprint before programming flight antifuse devices, de-risking the transition to screened RTAX2000S/SL V-suffix parts and avoiding costly scrappage of one-time-programmable flight units.
おすすめ
Spacecraft Attitude Control and Avionics
Attitude determination and control electronics require deterministic, SEU-tolerant logic. The RTAX2000S fabric features SEU-hardened registers, reducing the triple-module redundancy overhead needed in SRAM FPGAs, with family SEU rates below 1E-10 errors per bit-day. The RTAX2000S-1CQ256PROTO lets control-loop designers validate star-tracker and gyro interfaces against real CQ256 I/O electrical behavior. Its 540 kbits of embedded SRAM with optional EDAC buffers sensor data, and segmentable clock resources support redundant timing domains common in fault-tolerant avionics architectures.
おすすめ
Deep-Space Mission Electronics
For missions beyond low Earth orbit, cumulative ionizing dose is severe; the RTAX2000S family is specified at 300 krad functional and 200 krad parametric total dose, per the Microchip RTAX-S/SL datasheet. During instrument development, the RTAX2000S-1CQ256PROTO allows teams to run radiation-test campaigns and design freeze validation on representative hardware. The nonvolatile antifuse technology stores configuration in the interconnect itself, immune to configuration-memory upsets - a structural advantage over SRAM FPGAs in deep-space environments where reconfiguration opportunities are limited.
おすすめ
Defense and High-Reliability Ground Systems
High-reliability defense electronics, missile guidance consoles, and ground stations reuse RTAX2000S designs where configuration integrity and power-up immediacy matter. The RTAX2000S-1CQ256PROTO supports laboratory validation on the same CQ256 footprint used in production boards. Because the fabric is library-compatible with commercial Axcelerator devices, teams can port proven commercial IP, but application note AC170 warns internal timing differs significantly - making PROTO-unit timing verification essential. The 250,000 additional ASIC gates accommodate custom hard-block equivalent functions in the design.
おすすめ
FPGA Design Verification and Emulation
Verification teams pair the RTAX2000S-1CQ256PROTO with the Aldec ACT-H3Ki-CQ256 adaptor, which mounts in the RTAX footprint and uses flash-based ProASIC3E technology for unlimited reprogramming. The workflow iterates RTL on the flash adaptor, then programs the PROTO antifuse device to validate one-time-programmable behavior, package parasitics, and final timing. This two-stage approach, documented in the Microchip-Aldec prototyping collaboration, dramatically reduces risk before committing flight parts, since each antifuse device supports exactly one programming cycle.
おすすめ
Telemetry, Tracking and Command (TT&C) Units
TT&C subsystems demand always-on logic that is functional the instant spacecraft power arrives; the RTAX2000S antifuse fabric is live at power-up with no external configuration device, a direct system-level benefit for command receivers that must respond during launch and early orbit. The RTAX2000S-1CQ256PROTO enables board bring-up of these units with representative silicon. With up to 684 user I/Os available at family level and the CQ256 footprint offering a balanced I/O count, the device interfaces decoders, UARTs, and CCSDS framing logic on a single chip.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: RTAX2000S-1CQ256PROTO — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | RTAX2000SL-1CQ256PROTO | RTAX2000SL-1CQ256V |
|---|---|---|---|
| Package | CQ256 ceramic, 256 pins | CQ256 - same footprint | CQ256 - same footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Logic Blocks (CLBs) | 21504 | 21504 | 21504 |
| Equivalent System Gates | 2000000 | 2000000 | 2000000 |
| Fabric Variant | RTAX-S (standard power) | RTAX-SL (low static power) | RTAX-SL (low static power) |
| Product Grade | PROTO (engineering prototyping) | PROTO (engineering prototyping) | V (flight-screened) |
| Technology | Antifuse OTP, CMOS, live at power-up | Antifuse OTP, CMOS, live at power-up | Antifuse OTP, CMOS, live at power-up |
| Typical Use | Design validation before flight programming | Low-power design validation before flight programming | Space-flight qualification and launch hardware |
主な差別化要因
- PROTO workflow de-risks OTP flight devices （vs RTAX2000SL-1CQ256V)
- Same fabric and density as flight silicon （vs RTAX2000SL-1CQ256PROTO)
- Live-at-power-up antifuse configuration （vs SRAM-based prototyping fabrics (ProASIC3E adaptor))
設計ノート
PROTO devices are engineering parts, not flight hardware. Program an antifuse RTAX device only after design freeze: antifuse technology is one-time programmable and a single mistake scraps the unit. Follow Microchip application note AC170 - although RTAX-S is library-compatible with Axcelerator, internal timing differs significantly, so never sign off timing using commercial Axcelerator models. Use RTAX-S timing models in Libero SoC and validate on the PROTO device before programming V-suffix flight parts.
If your spacecraft power budget is tight, evaluate the RTAX2000SL variant: the SL fabric provides the same 21,504-CLB density and CQ256 footprint with lower static power consumption, per the RTAX-S/SL family datasheet. Because S and SL are pin-compatible, you can prototype on either PROTO device and migrate to the SL flight part without PCB changes; update static-current analysis and thermal figures in your power budget when switching families.
Design the CQ256 land pattern once and reuse it across the RTAX2000S/SL PROTO and flight-suffix variants to preserve second-source flexibility within the family. Decouple all VCCA, VCCI, and VJTAG supplies with low-ESR ceramics placed close to the package; follow the RTAX-S/SL datasheet power-supply section for recommended capacitor values. Consider footprint compatibility with the Aldec ACT-H3Ki-CQ256 reprogrammable adaptor during layout so the flash-based prototyping path remains available.
コンプライアンス情報
Compliance data for this aerospace prototyping device was not stated in the provided web data; hermetic ceramic CQ packaging typically follows MIL-style screening rather than commercial RoHS documentation. Verify with Microchip.
