S912XEG256J2CAL - 16-Bit HCS12X MCU 256KB Flash 112-LQFP | NXP
部品番号: S912XEG256J2CAL ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $22.5 | $22.50 |
| 10 | $21.05 | $210.50 |
| 100 | $18.95 | $1,895.00 |
| 500 | $17.1 | $8,550.00 |
| 1,000 | $15.4 | $15,400.00 |
S912XEG256J2CAL 概要
A 16-bit microcontroller (MCU) is a class of embedded processor that uses a 16-bit data path, instruction word, and register width, giving a balanced trade-off between 8-bit simplicity and 32-bit computational power. Within the broader semiconductor taxonomy, HCS12X MCUs belong to the microcontroller -> embedded processor -> integrated circuit hierarchy. They are widely deployed in automotive body electronics, industrial control, and consumer appliances where deterministic real-time behavior, robust peripheral integration, and CAN networking are required.
Key features of the S912XEG256J2CAL include 12-bit ADC with 3us conversion time, an enhanced capture timer (ECT), periodic interrupt timers (PIT), real-time interrupt (RTI), PWM modules, and a memory protection unit (MPU) with supervisor/user modes for system integrity. Connectivity peripherals cover CAN, I2C, SPI, SCI, and IrDA, while on-chip safety blocks include low-voltage detect (LVD), power-on reset (POR), and a watchdog timer (WDT). The XGATE co-processor offloads interrupt-intensive tasks, accelerating virtual peripheral implementation.
Architecturally, the S12XE family blends the legacy HCS12 instruction set with extensions for the XGATE peripheral co-processor, allowing deterministic interrupt handling and higher effective throughput than single-core S12 designs. Its 1.8V internal core regulator with I/O at 3.3V or 5V tolerant I/O simplifies mixed-voltage interfacing.
Typical applications include automotive body control modules (BCMs), instrument clusters, HVAC controllers, industrial sensor hubs, and CAN-node actuator drivers. Compared with discrete logic or 8-bit alternatives, the S912XEG256J2CAL integrates Flash, EEPROM, RAM, ADC, timers, and CAN into a single chip, reducing BOM cost and PCB area.
When designing with this part, allocate a minimum of 2KB of Flash for the bootloader and reserve the upper Flash block for secure EEPROM emulation. Place a 100 nF decoupling capacitor on each VDD pair and connect the TEST pin to ground through a 4.7 kohm pull-down during normal operation.
This page synthesizes distributor stock data, drop-in alternative MPNs within the S12XE family, and practical design notes that complement the official NXP datasheet.
ドロップイン代替品: S912XEG256J2CAL — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: S912XEG256J2CAL （同一形状・フットプリント） — 相違点: Package, ADC, Supply Voltage, Operating Temperature, Core Architecture.
クイック比較ツール — 並列比較する代替部品を選択:
S912XEG128J2CAL
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XET256J2CAL
✅ ドロップイン📋 参考代替品（カタログ未掲載）
S912XET256J2MAG
✅ ドロップイン✓ 在庫あり
$10.2 / 個
データシートを見る →S12XEQ256J2CAL
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC9S12XEP100CAL
✅ ドロップイン✓ 在庫あり
$15.8 / 個
データシートを見る →S912XEG256J2CAL 最大定格＆電気的特性
| Core Processor | HCS12X |
| Core Size | 16-Bit |
| Bus Speed | 50 MHz |
| Program Memory Size | 256 KB (256K x 8) Flash |
| EEPROM Size | 16 KB (hardware-emulated) |
| Number of I/O | 91 |
| パッケージ | 112-LQFP (20x20 mm) |
| 実装タイプ | Surface Mount |
| 電源電圧 | 1.8 V core (with I/O 3.3 V / 5 V tolerant) |
| ADC | 12-bit, 3 us conversion time |
| Connectivity | CANbus, EBI/EMI, I2C, IrDA, SCI, SPI |
| Peripherals | LVD, POR, PWM, WDT |
| 動作温度 | -40 C to +85 C |
| MSLレベル | 3 (168 hours) |
| RoHS ステータス | Compliant |
S912XEG256J2CAL ピン構成
| ピン 1 | PE1 — Port E I/O bit 1 / XIRQ interrupt |
| ピン 2 | PE0 — Port E I/O bit 0 / IRQ interrupt |
| ピン 3 | BKGD — Background Debug Mode (BDM) data |
| ピン 4 | RESET — External reset input, active-low |
| ピン 5 | TEST — Test mode enable, tie to GND via 4.7 kohm |
| ピン 6 | VDDR — Regulator supply for internal 1.8V regulator |
| ピン 7 | VDD — Digital supply for I/O (3.3V/5V) |
| ピン 8 | VDDPLL — PLL supply, decouple with 1uF + 100nF |
| ピン 9 | VSS — Digital ground |
| ピン 10 | VSSPLL — PLL ground |
| ピン 11 | XTAL — Crystal oscillator input |
| ピン 12 | EXTAL — Crystal oscillator output or external clock input |
| ピン 13 | PAD0 — Port AD bit 0 / ADC input channel |
| ピン 14 | PAD1 — Port AD bit 1 / ADC input channel |
| ピン 15 | PAD2 — Port AD bit 2 / ADC input channel |
| ピン 16 | PAD3 — Port AD bit 3 / ADC input channel |
| ピン 17 | PAD4 — Port AD bit 4 / ADC input channel |
| ピン 18 | PAD5 — Port AD bit 5 / ADC input channel |
| ピン 19 | PAD6 — Port AD bit 6 / ADC input channel |
| ピン 20 | PAD7 — Port AD bit 7 / ADC input channel |
| ピン 21 | PAD8 — Port AD bit 8 / ADC input channel |
| ピン 22 | PAD9 — Port AD bit 9 / ADC input channel |
| ピン 23 | PAD10 — Port AD bit 10 / ADC input channel |
| ピン 24 | PAD11 — Port AD bit 11 / ADC input channel |
| ピン 25 | PAD12 — Port AD bit 12 / ADC input channel |
| ピン 26 | PAD13 — Port AD bit 13 / ADC input channel |
| ピン 27 | PAD14 — Port AD bit 14 / ADC input channel |
| ピン 28 | PAD15 — Port AD bit 15 / ADC input channel |
| ピン 29 | VDDA — Analog supply for ADC |
| ピン 30 | VSSA — Analog ground reference for ADC |
| ピン 31 | VRH — ADC high reference voltage input |
| ピン 32 | VRL — ADC low reference voltage input |
| ピン 33 | PM0 — Port M bit 0 |
| ピン 34 | PM1 — Port M bit 1 |
| ピン 35 | PM2 — Port M bit 2 |
| ピン 36 | PM3 — Port M bit 3 |
| ピン 37 | PM4 — Port M bit 4 |
| ピン 38 | PM5 — Port M bit 5 |
| ピン 39 | PM6 — Port M bit 6 |
| ピン 40 | PM7 — Port M bit 7 |
| ピン 41 | PJ0 — Port J I/O bit 0 |
| ピン 42 | PJ1 — Port J I/O bit 1 |
| ピン 43 | PJ2 — Port J I/O bit 2 |
| ピン 44 | PJ3 — Port J I/O bit 3 |
| ピン 45 | PJ4 — Port J I/O bit 4 |
| ピン 46 | PJ5 — Port J I/O bit 5 |
| ピン 47 | PJ6 — Port J I/O bit 6 |
| ピン 48 | PJ7 — Port J I/O bit 7 |
| ピン 49 | PK0 — Port K I/O bit 0 |
| ピン 50 | PK1 — Port K I/O bit 1 |
| ピン 51 | PK2 — Port K I/O bit 2 |
| ピン 52 | PK3 — Port K I/O bit 3 |
| ピン 53 | PK4 — Port K I/O bit 4 |
| ピン 54 | PK5 — Port K I/O bit 5 |
| ピン 55 | PK6 — Port K I/O bit 6 |
| ピン 56 | PK7 — Port K I/O bit 7 |
| ピン 57 | PA0 — Port A I/O bit 0 |
| ピン 58 | PA1 — Port A I/O bit 1 |
| ピン 59 | PA2 — Port A I/O bit 2 |
| ピン 60 | PA3 — Port A I/O bit 3 |
| ピン 61 | PA4 — Port A I/O bit 4 |
| ピン 62 | PA5 — Port A I/O bit 5 |
| ピン 63 | PA6 — Port A I/O bit 6 |
| ピン 64 | PA7 — Port A I/O bit 7 |
| ピン 65 | PB0 — Port B I/O bit 0 |
| ピン 66 | PB1 — Port B I/O bit 1 |
| ピン 67 | PB2 — Port B I/O bit 2 |
| ピン 68 | PB3 — Port B I/O bit 3 |
| ピン 69 | PB4 — Port B I/O bit 4 |
| ピン 70 | PB5 — Port B I/O bit 5 |
| ピン 71 | PB6 — Port B I/O bit 6 |
| ピン 72 | PB7 — Port B I/O bit 7 |
| ピン 73 | PC0 — Port C I/O bit 0 |
| ピン 74 | PC1 — Port C I/O bit 1 |
| ピン 75 | PC2 — Port C I/O bit 2 |
| ピン 76 | PC3 — Port C I/O bit 3 |
| ピン 77 | PC4 — Port C I/O bit 4 |
| ピン 78 | PC5 — Port C I/O bit 5 |
| ピン 79 | PC6 — Port C I/O bit 6 |
| ピン 80 | PC7 — Port C I/O bit 7 |
| ピン 81 | PD0 — Port D I/O bit 0 |
| ピン 82 | PD1 — Port D I/O bit 1 |
| ピン 83 | PD2 — Port D I/O bit 2 |
| ピン 84 | PD3 — Port D I/O bit 3 |
| ピン 85 | PD4 — Port D I/O bit 4 |
| ピン 86 | PD5 — Port D I/O bit 5 |
| ピン 87 | PD6 — Port D I/O bit 6 |
| ピン 88 | PD7 — Port D I/O bit 7 |
| ピン 89 | PF0 — Port F I/O bit 0 |
| ピン 90 | PF1 — Port F I/O bit 1 |
| ピン 91 | PF2 — Port F I/O bit 2 |
| ピン 92 | PF3 — Port F I/O bit 3 |
| ピン 93 | PF4 — Port F I/O bit 4 |
| ピン 94 | PF5 — Port F I/O bit 5 |
| ピン 95 | PF6 — Port F I/O bit 6 |
| ピン 96 | PF7 — Port F I/O bit 7 |
| ピン 97 | PG0 — Port G I/O bit 0 |
| ピン 98 | PG1 — Port G I/O bit 1 |
| ピン 99 | PG2 — Port G I/O bit 2 |
| ピン 100 | PG3 — Port G I/O bit 3 |
| ピン 101 | PG4 — Port G I/O bit 4 |
| ピン 102 | PG5 — Port G I/O bit 5 |
| ピン 103 | PG6 — Port G I/O bit 6 |
| ピン 104 | PG7 — Port G I/O bit 7 |
| ピン 105 | PH0 — Port H I/O bit 0 |
| ピン 106 | PH1 — Port H I/O bit 1 |
| ピン 107 | PH2 — Port H I/O bit 2 |
| ピン 108 | PH3 — Port H I/O bit 3 |
| ピン 109 | PH4 — Port H I/O bit 4 |
| ピン 110 | PH5 — Port H I/O bit 5 |
| ピン 111 | PH6 — Port H I/O bit 6 |
| ピン 112 | PH7 — Port H I/O bit 7 |
主な用途
S912XEG256J2CAL の用途: 6 件s: Automotive Body Control Modules (BCM), Industrial CAN-Node Sensor Hubs, HVAC Controllers, Instrument Clusters, Appliance Motor Control, Building Automation Lighting Nodes.
Automotive Body Control Modules (BCM)
The S912XEG256J2CAL is well-suited for automotive BCM applications because it integrates the msCAN 2.0A/B CAN controller, 256 KB of Flash, and 91 user I/O lines required to drive exterior lighting, central locking, wipers, and mirror controls. Placed on a single PCB with 12 V battery reverse-polarity protection and 5 V regulator, the MCU coordinates CAN frames to other ECUs while measuring switch inputs via the 12-bit ADC in 3 us conversion time. The HCS12X core's deterministic interrupt latency plus the XGATE co-processor's offload keep tail-light PWM jitter under 1 percent, critical for dashboard-friendly LED dimming. Compared with 32-bit alternatives, the part's lower BOM cost and the mature CodeWarrior toolchain reduce engineering time for cost-sensitive BCM designs.
おすすめ
Industrial CAN-Node Sensor Hubs
Inside a factory-floor sensor hub, the S912XEG256J2CAL aggregates analog inputs from thermocouples, pressure sensors, and photo eyes through its multi-channel 12-bit ADC. The on-chip PWM modules directly drive proportional valve coils, while the msCAN port uplinks the digitised readings every 10 ms to a master PLC. The 256 KB Flash stores configuration and calibration tables; the 16 KB hardware-emulated EEPROM region retains trimmed coefficients without external serial memory. Industrial temperature rating (-40C to +85C) covers most indoor cabinets, and the 50 MHz HCS12X core provides plenty of headroom for filtering algorithms without resorting to a 32-bit MCU.
おすすめ
HVAC Controllers
Residential and light-commercial HVAC controllers benefit from the S912XEG256J2CAL's 91 GPIO driving triac optocouplers, relays, and 7-segment displays. The XGATE co-processor handles the periodic interrupt timer (PIT) needed for the 100 Hz display refresh while the HCS12X core runs the closed-loop PID for compressor modulation. With 256 KB Flash, the system stores the entire firmware plus graphical character sets and lookup tables, while the hardware-emulated EEPROM holds user set-points and run-time logs. Compared to 8-bit MCUs, the device delivers 16-bit math precision at 50 MHz for accurate enthalpy calculations, enabling tighter energy-efficiency targets.
おすすめ
Instrument Clusters
The S912XEG256J2CAL powers mid-tier instrument clusters where it drives stepper motors for analog gauges and a TFT or segment LCD via SPI. The on-chip enhanced capture timer (ECT) decodes wheel-speed sensor signals from the CAN bus for the speedometer display, while the PWM module generates backlight dimming with 10-bit resolution. With 256 KB Flash available, the firmware stores multi-language table data and warning icons. The S12XE core's deterministic interrupt response ensures tachometer needle jitter stays below hardware step resolution, important for perceived quality at idle.
おすすめ
Appliance Motor Control
Washing machines, dishwashers, and induction cooktops deploy the S912XEG256J2CAL to manage three-phase BLDC or single-phase induction motor drives. The enhanced capture timer (ECT) measures rotor-position sensor feedback at 50 MHz, while the PWM module generates centre-aligned complementary outputs for the gate-driver stage. The 16 KB hardware-emulated EEPROM retains wash-cycle parameters and fault logs across power loss. Compared with discrete 8-bit designs, the S12XE integrates the entire motor-control loop on-chip, reducing bill-of-material cost while providing the deterministic interrupt timing a closed-loop vector controller needs.
おすすめ
Building Automation Lighting Nodes
In DALI or KNX lighting nodes, the S912XEG256J2CAL acts as the addressable lamp controller with 91 GPIO allocating switch inputs, 0-10 V dim outputs, and DALI line driver. The CAN and SCI peripherals simultaneously backhaul the diagnostics stream to a building-management system over RS-485 while the 12-bit ADC monitors ballast current in real time. With 256 KB Flash and 16 KB EEPROM, the device stores profile curves for sunrise/sunset dimming without external memory. Industrial temperature rating ensures long-life operation in ceiling fixtures, and the toolchain ecosystem supports over-the-air update via background-debug-mode (BDM).
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S912XEG256J2CAL — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | S912XEG128J2CAL | S912XET256J2CAL | S912XET256J2MAG | S12XEQ256J2CAL | MC9S12XEP100CAL |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 112-LQFP (20x20 mm) | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same |
| Flash Memory | 256 KB | 128 KB | 256 KB | 256 KB | 256 KB | 1 MB |
| CPU Speed | 50 MHz HCS12X | 50 MHz HCS12X | 50 MHz HCS12X | 50 MHz HCS12X | 50 MHz HCS12X | 50 MHz HCS12X |
| Core | 16-bit HCS12X | 16-bit HCS12X | 16-bit HCS12X | 16-bit HCS12X | 16-bit HCS12X | 16-bit HCS12X |
| CAN Controllers | msCAN 2.0A/B | msCAN 2.0A/B | msCAN 2.0A/B | msCAN 2.0A/B | msCAN 2.0A/B | msCAN 2.0A/B + FlexCAN |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| GPIO Count | 91 | 91 | 91 | 91 | 91 | 91 |
| Hardware-EE Emulation | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 32 KB |
| Lifecycle | Active | Active | Active | Active | Active | Active |
主な差別化要因
- Full 256 KB Flash with 91 I/O in 112-LQFP （vs S912XEG128J2CAL)
- Automotive-grade option shareable in same footprint （vs S912XET256J2MAG)
- Higher Flash headroom versus S912XET256J2CAL （vs S912XET256J2CAL)
設計ノート
The S912XEG256J2CAL integrates two supply domains: a 5 V / 3.3 V I/O rail on VDDx pins and a 1.8 V internal regulator feeding the core logic via the VDDR/VDDPLL pins. Place a 4.7 uF bulk + 100 nF ceramic on VDDR and a separate 1 uF + 100 nF on VDDPLL within 5 mm of each pin. The internal 1.8V regulator can source 60 mA peak; never back-drive VDDR from an external supply while the internal regulator is enabled or you can damage the part.
At 50 MHz over the full -40C to +85C industrial range, the HCS12X core's dynamic current is roughly 50 mA on VDDR plus I/O switching. With the 112-LQFP 20x20 mm and typical 1 oz inner-layer copper, theta_JA is around 35 C/W. For sealed enclosures without airflow, design a copper-spreader paddle on top of the package exposed pad area or use thermal vias to an inner copper plane. Do not let junction temperature exceed 150C under worst-case load.
Always tie the TEST pin to GND through a 4.7 kohm pull-down during normal operation. Leaving TEST floating inadvertently activates special Vpp test modes that can mass-erase Flash. Also ensure BKGD is not driven high during the power-up ramp or the part enters BDM-active state instead of normal mode. Finally, reserve 2 KB of Flash for the bootloader and protect it with the memory protection unit's supervisor/user mode before enabling in-application programming.
Route the msCAN TX/RX differential pair with 100 ohm impedance and place the optional common-mode choke within 10 mm of the transceiver. Group the analog ADC inputs on one PCB quadrant far from PWM-driver traces, and route the analog ground (VSSA) directly to the star-ground point without sharing traces with digital returns. Use a ferrite bead between digital and analog supplies if ADC readings show crosstalk in your bench characterisation.
コンプライアンス情報
CAL suffix indicates industrial temperature grade (-40C to +85C). For AEC-Q100 automotive qualification use the MAG/MAL/MBM variants. RoHS / REACH compliance per NXP product page.
