S9S08AW60E5MFUE - 40MHz 60KB Automotive 8-Bit MCU | NXP
部品番号: S9S08AW60E5MFUE ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
S9S08AW60E5MFUE 概要
A microcontroller is a programmable integrated circuit that executes firmware, reads sensor and switch inputs, controls actuators, and coordinates communications within an electronic product. The S08 MCU belongs to the HCS08 family and sits within the broader hierarchy of MCU, embedded processor, semiconductor, and control-system components. This family-oriented architecture supports compact motor, body, appliance, and industrial-control designs where adequate performance and peripheral integration matter more than 32-bit processing.
Key verified features include an 8-bit S08 core, 40 MHz maximum speed, 60 KB organized as 60K x 8 Flash, 54 I/O pins, and I2C, SCI, and SPI connectivity. The device also includes low-voltage detection, power-on reset, PWM, and a watchdog timer. Its automotive temperature grade and 64-terminal QFP package make it suitable for applications requiring broad environmental tolerance and conventional leaded-package inspection.
The S08 core uses an integrated, highly integrated 8-bit architecture optimized for embedded control rather than high-bandwidth computing. Flash permits in-system firmware storage and programming, while the listed communication peripherals support sensors, transceivers, and industrial serial equipment. Because no EEPROM, cache, or instruction-cache data was supplied, those characteristics should not be inferred from unrelated family members.
Typical uses include automotive body and seating controls, small motor controllers, relay and solenoid interfaces, instrumentation, appliance control, and industrial automation modules. The 54 available I/O pins are especially useful when a design needs multiple digital signals alongside I2C, SCI, or SPI connectivity. The 40 MHz clock rate provides a defined performance ceiling for scheduling control loops, although real response time remains dependent on firmware and peripheral configuration.
For PCB implementation, preserve the manufacturer's recommended power, ground, decoupling, programming, and clock connections. Place bypass capacitors close to supply pins and route sensitive clock and communication traces away from fast-switching nodes. Before substitution, verify package pinout, memory organization, peripheral mapping, voltage limits, and automotive qualification rather than relying only on the 64-QFP designation.
This page consolidates verified distributor specifications, availability sources, and application guidance for engineers evaluating the S9S08AW60E5MFUE. It also separates confirmed facts from unavailable parameters, supporting faster sourcing decisions without presenting unsupported electrical, pricing, or pin-level claims.
ドロップイン代替品: S9S08AW60E5MFUE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストS9S08AW60E5MFUE 最大定格＆電気的特性
| Product Type | 8-bit Microcontroller Unit (MCU) |
| Core Processor | S08 Core |
| Processor Architecture | 8-bit CISC |
| 最大クロック周波数 | 40 MHz |
| Program Memory Size | 60 KB (60K x 8) |
| Program Memory Type | Flash |
| RAM Size | 2K x 8 |
| Number of I/O Pins | 54 pins |
| 電源電圧 | 3.3 V / 5 V |
| 動作温度範囲 | -40°C to +125°C |
| Temperature Grade | Automotive |
| パッケージ | 64-pin QFP (14 x 14 mm) |
| Terminal Count | 64 terminals |
| 実装タイプ | Surface mount |
| Connectivity | I2C, SCI, SPI |
| Peripherals | LVD, POR, PWM, WDT |
S9S08AW60E5MFUE 64-pin qfp (14 x 14 mm) ピン配置ガイド
S9S08AW60E5MFUE (64-pin qfp (14 x 14 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: S9S08AW60E5MFUE.
詳細は データシート をご参照ください。
主な用途
S9S08AW60E5MFUE の用途: 6 件s: Automotive Body-Control Module, Seat and Door Control Module, Small Motor Controller, Industrial Sensor Interface, Appliance Control System, Communication Gateway Module.
Automotive Body-Control Module
The S9S08AW60E5MFUE fits a compact body-control module that coordinates switches, lamps, locks, and small electromechanical loads. Its 54 I/O pins provide substantial digital connectivity, while the 40 MHz S08 core gives firmware room for state logic and timing tasks beyond a very small 8-bit device. The verified -40°C to +125°C range and automotive grade make it more appropriate for temperature-variable vehicle environments than an unspecified commercial-temperature MCU. In implementation, use the I2C, SCI, or SPI interface for compatible sensors or remote modules, and isolate loads from sensitive signal paths. Final qualification still requires checking the exact electrical limits, watchdog strategy, fault behavior, and automotive program requirements in the manufacturer documentation.
おすすめ
Seat and Door Control Module
A seat, door, or window controller can use the S9S08AW60E5MFUE to combine motor timing, limit-switch monitoring, button inputs, and status reporting in one controller. The 60 KB Flash capacity provides room for calibration tables and organized application logic, while 54 I/O pins reduce the need for external logic where many direct connections are required. SCI or SPI can connect to position sensors or companion electronics, and I2C is available for compatible low-speed peripheral devices. Because motor and solenoid paths create electrical transients, the implementation should preserve the verified 3.3 V or 5 V supply domain and follow manufacturer grounding and protection guidance. Firmware should include movement limits, stuck-motor detection, and watchdog recovery rather than relying solely on nominal timing.
おすすめ
Small Motor Controller
The S9S08AW60E5MFUE is appropriate for a small brushed-motor controller that needs deterministic command handling, multiple digital status inputs, and serial diagnostics. Its 40 MHz S08 processor supports faster control calculations than a low-clock 8-bit MCU, and PWM is explicitly included among the verified peripherals. The 54 I/O pins can distribute limit switches, Hall or sensor inputs, fault signals, and driver-control outputs. In a typical circuit, the MCU would execute a state machine, calculate motor commands, monitor feedback, and report faults through SCI or SPI. Power-stage transients are the dominant design risk, so keep high-current switching paths separate from MCU power and signal routing. Exact PWM frequency, timer channels, current limits, and pin assignments remain datasheet-dependent and must be verified before implementation.
おすすめ
Industrial Sensor Interface
S9S08AW60E5MFUE can serve as the local controller for an industrial sensor interface that gathers switch states and communicates measurement data. I2C, SCI, and SPI are all identified in the verified data, allowing the design to connect different sensor classes without forcing one communications protocol across the system. Its 8-bit architecture and 60 KB Flash are suitable for calibration, filtering, diagnostics, and protocol handling when the workload does not require 32-bit arithmetic. The -40°C to +125°C rating broadens its potential industrial range, but it does not itself establish compliance with any industrial standard. Engineers should add appropriate input conditioning, transient protection, and isolation outside the MCU, then verify the selected peripheral pins and voltage limits from the complete datasheet.
おすすめ
Appliance Control System
For an appliance controller, the S9S08AW60E5MFUE can manage user inputs, display or indicator signals, sensors, relays, and communications in a single 8-bit platform. Its 54 I/O pins reduce multiplexing pressure, while the 40 MHz clock and 60 KB Flash support structured state machines, diagnostic codes, and configurable product variants. The integrated LVD, POR, PWM, and WDT functions support robust embedded behavior, although the source does not provide detailed thresholds or timer limits. In a design, PWM could operate low-power actuators, SCI could expose diagnostics, and discrete I/O could drive indicators or safety-related interlocks. Engineers must validate whether the available Flash and RAM satisfy the complete firmware build and add appropriate mains isolation and surge protection for appliances connected to hazardous power.
おすすめ
Communication Gateway Module
The S9S08AW60E5MFUE can act as a small gateway that translates among I2C, SCI, and SPI-connected modules and coordinates local I/O behavior. Its 60 KB Flash provides room for protocol state machines and configuration data, while the 40 MHz S08 core supports responsive task scheduling. SCI is suitable for a host link, SPI can serve faster peripherals, and I2C can connect to low-speed sensors or converters. Because no cache or advanced communications accelerator was verified, designers should not treat the MCU as a high-throughput protocol engine without workload analysis. Keep serial routing away from motors and switching supplies, use controlled bus rates, and validate timing against the selected peripheral pins. Firmware should include framing checks, timeout recovery, and watchdog reset handling to prevent a failed link from leaving actuators in an unsafe state.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: S9S08AW60E5MFUE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
設計ノート
Use the complete manufacturer pin table before routing the PCB because the supplied data confirms a 64-terminal QFP package but does not enumerate individual pins. Keep clock and serial traces away from motor-switching or inductive paths, maintain short ground returns, and place required bypass capacitors at the package power connections. The 14 x 14 mm body also leaves limited routing escape space on fine-pitch boards, so fanout and assembly clearances should be reviewed early.
The verified listing identifies 3.3 V and 5 V device variants, but it does not provide exact operating ranges or external-component values. Select the correct ordering variant and design the supply, decoupling, reset, and brownout behavior from the manufacturer datasheet rather than assuming both voltage options can be used simultaneously. Keep high-current load returns separate from sensitive signal ground where practical, and validate startup and brownout behavior across the complete supply range.
Do not treat the AW60 family name as sufficient proof that any suffix is interchangeable. One comparison snippet associates MC9S08AW60CFUER with 16 KB Flash while the target has 60 KB, demonstrating why suffix-level verification is essential. Before substitution, compare memory density, RAM, package dimensions, exposed or thermal pad requirements, clocking, peripheral pin mapping, voltage limits, temperature grade, and qualification documentation.
The target exposes I2C, SCI, SPI, PWM, and general-purpose I/O, so a mixed-signal design can easily couple communications timing to actuator transitions. Terminate interfaces only according to the actual topology and datasheet guidance, avoid long unprotected stubs, and provide series resistance or proper pull-up networks where supported. Validate rise time, idle levels, and bus timing on the physical PCB because the supplied snippets do not provide pin-specific timing limits.
コンプライアンス情報
The verified data labels the part automotive qualified or automotive temperature grade, but it does not explicitly state AEC-Q100 qualification, RoHS compliance, REACH compliance, lead-free status, halogen-free status, or conflict-minerals compliance. Those fields remain unknown rather than inferred.
