SN74HC125N - 4-Channel 3-State Buffer | Texas Instruments
部品番号: SN74HC125N ✓ 生産中SN74HC125N 概要
A logic buffer is a digital IC that reproduces a binary input signal at its output while providing electrical isolation and drive strength between connected circuit sections. The SN74HC125 belongs to the 74HC CMOS logic family and operates as a bus buffer or line driver within a broader digital-logic hierarchy. Its three-state outputs can present a low level, a high level, or a high-impedance state, allowing multiple devices to share a bus when only one output is enabled at a time.
The four independent output-enable inputs are useful for bus isolation, bidirectional-style signal multiplexing, and processor or peripheral interface designs. The non-inverting architecture preserves the logical polarity of each data input. Because the outputs can enter a high-impedance state, designers can place several buffered devices on one shared signal path without allowing disabled outputs to fight each other during normal operation.
The SN74HC125N operates from a 2 V to 6 V power supply and uses three-state output behavior. Its 14-pin PDIP package is intended for through-hole assembly and is also practical for prototyping boards, legacy industrial equipment, and repair applications. The manufacturer identifies the device as a quadruple bus buffer with three-state outputs, while the product page describes it as a four-channel, 2 V to 6 V buffer family.
Typical uses include buffering shared data buses, isolating a peripheral from a multi-device bus, driving control signals into sections of a larger logic system, and creating selectable output paths. The individual enable inputs allow each of the four channels to participate in or be removed from a shared bus independently. This flexibility is valuable in systems where several sources must share conductors without continuous drive contention.
For reliable three-state operation, ensure that no more than one enabled output drives a shared node at the same time. Check the manufacturer datasheet for input thresholds, output current limits, load-capacitance limits, propagation delay, and input/output current limits before assigning a specific system operating condition or fanout requirement.
This page combines the Texas Instruments product information, the official SN74HC125 datasheet, verified distributor listings, and cross-reference findings with practical guidance for bus design, replacement assessment, and footprint-aware part selection.
ドロップイン代替品: SN74HC125N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
SN74HC125NE4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD74HC125E
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
M74HC125B1R
✅ ドロップイン📋 参考代替品(カタログ未掲載)
74AHCT125N
✅ ドロップイン📋 参考代替品(カタログ未掲載)
74HC125N
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SN74HC125N 最大定格&電気的特性
| Product Type | Quadruple non-inverting bus buffer with three-state outputs |
| Number of Elements | 4 elements |
| Number of Channels | 4 channels |
| Bits per Element | 1 bit per element |
| Supply Voltage Range | 2 V to 6 V |
| 出力タイプ | 3-state output |
| Logic Level | CMOS |
| Input Polarity | Non-inverting |
| Output Enable Control | 4 independent active-low output-enable inputs |
| パッケージ | 14-PDIP, through-hole |
| ピン数 | 14 pins |
| 実装タイプ | Through-hole |
SN74HC125N ピン構成
| ピン 1 | 1OE — Active-low output enable for buffer 1 |
| ピン 2 | 1A — Data input for buffer 1 |
| ピン 3 | 1Y — Three-state output for buffer 1 |
| ピン 4 | GND — Ground |
| ピン 5 | 2OE — Active-low output enable for buffer 2 |
| ピン 6 | 2A — Data input for buffer 2 |
| ピン 7 | 2Y — Three-state output for buffer 2 |
| ピン 8 | 3Y — Three-state output for buffer 3 |
| ピン 9 | 3A — Data input for buffer 3 |
| ピン 10 | 3OE — Active-low output enable for buffer 3 |
| ピン 11 | 4Y — Three-state output for buffer 4 |
| ピン 12 | 4A — Data input for buffer 4 |
| ピン 13 | 4OE — Active-low output enable for buffer 4 |
| ピン 14 | VCC — Power supply |
主な用途
SN74HC125N の用途: 6 件s: Shared Data-Bus Isolation, Peripheral Interface Buffering, Selectable Signal Routing, Industrial Control Logic, Test and Measurement Interfacing, Retrofit and Prototype Logic.
Shared Data-Bus Isolation
The SN74HC125N is suitable for placing several logic devices on one data conductor while ensuring that only one channel drives the bus at a time. Its four independent active-low output-enable inputs allow each buffer to be disconnected into a high-impedance state, reducing the risk of output contention. The device can therefore isolate processor, memory, and peripheral signals on a shared bus without requiring four separate single-channel buffers. When designing the circuit, assign one enable at a time to any shared node and review the manufacturer limits for output current, load capacitance, and transition behavior.
おすすめ
Peripheral Interface Buffering
The SN74HC125N provides a controlled interface between a logic bus and a peripheral whose outputs may need to be disconnected. Four non-inverting channels can buffer four related signals, while the individual three-state controls permit only the active peripheral to drive the shared lines. This arrangement can reduce loading on the originating device and make the bus direction unambiguous. The 2 V to 6 V operating range supports standard CMOS logic domains, and the 14-pin PDIP package simplifies through-hole prototyping and repair. Validate timing against the peripheral and the connected bus before finalizing the interface.
おすすめ
Selectable Signal Routing
The SN74HC125N can create a selectable signal path by driving a common node from one enabled buffer while the other outputs remain high impedance. With four data inputs and four active-low enable controls, the device supports compact multiplexing without requiring a separate general-purpose analog switch. Because the logic is non-inverting, the selected channel preserves the source signal polarity. The implementation is especially useful for routing compatible digital levels among several functional blocks. Confirm that every disabled output is connected only to a node it does not need to hold, and verify the datasheet's output drive and load-capacitance limits.
おすすめ
Industrial Control Logic
The SN74HC125N can buffer control and status signals within industrial logic assemblies where multiple subsystems connect to common conductors. Its four independent three-state channels support orderly bus participation, while non-inverting operation avoids altering the intended control polarity. The 14-pin PDIP package is useful for repairable, through-hole legacy equipment and for industrial prototypes requiring easy inspection and replacement. At commissioning, verify that firmware or discrete control logic enables only one driver for each shared node. Confirm operating-temperature requirements and electrical margins against the relevant equipment specification before deployment.
おすすめ
Test and Measurement Interfacing
The SN74HC125N can isolate test-bus or fixture signals from the circuit under test by placing its outputs into a high-impedance state when they are not selected. This helps prevent inactive fixture channels from loading sensitive nodes. Four channels allow several related control or measurement-interface lines to be managed by one device, and the non-inverting operation simplifies correspondence with the source signal. The 2 V to 6 V range covers common CMOS test-equipment levels, subject to the actual interface voltage. Verify the input thresholds, timing, and capacitive loading at the connected fixture before using the buffer at higher signaling rates.
おすすめ
Retrofit and Prototype Logic
The SN74HC125N is a practical choice for through-hole prototypes, educational assemblies, and repairs of older CMOS logic systems because it combines four buffers in one 14-pin PDIP package. Installers can use the active-low enable inputs to build simple multiplexing or isolation arrangements while retaining recognizable standard logic behavior. The 2 V to 6 V supply range permits operation in established 5 V designs and lower-voltage CMOS systems when the surrounding circuit supports it. For reliable construction, check orientation, supply decoupling, and the enable-state truth table in the official manufacturer datasheet before energizing the board.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74HC125N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN74HC125NE4 | CD74HC125E | M74HC125B1R | 74AHCT125N | 74HC125N |
|---|---|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | Nexperia | Nexperia |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Output Type | 3-state output | 3-state output | 3-state output | 3-state output | 3-state output | 3-state output |
| Logic Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Output Enable | 4 independent active-low enables | 4 independent active-low enables | 4 independent active-low enables | 4 independent active-low enables | 4 independent active-low enables | 4 independent active-low enables |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Input Threshold Family | 74HC CMOS | 74HC CMOS | 74HC CMOS | 74HC CMOS | 74AHCT TTL-compatible | 74HC CMOS |
主な差別化要因
- Four independently controlled three-state channels in one through-hole package (vs 74AHCT125N)
- Uses standard 74HC CMOS input thresholds for CMOS-system compatibility (vs 74AHCT125N)
- Direct footprint compatibility with established 14-PDIP 74HC125-family devices (vs M74HC125B1R)
設計ノート
Ensure that only one enabled output connects to any shared bus node. The three-state output becomes high impedance when its active-low output-enable input is high, but two simultaneously enabled channels can still create output contention if they drive different levels into the same conductor. Review the complete enable truth table and assign disjoint enable controls before connecting multiple devices to a common bus.
Keep the SN74HC125N close to the logic family that drives or receives its buffered signals, especially when the net has appreciable capacitance. The 14-pin PDIP format makes breadboard and through-hole prototype construction straightforward, but long point-to-point wiring can add propagation delay and susceptibility to noise. Use short, direct traces on assembled boards and maintain a common ground reference between the buffer and connected logic devices.
Apply a stable supply within the documented 2 V to 6 V range and follow the manufacturer recommendations for bypassing and unused inputs. Do not allow a signal to exceed the device's specified input limits, particularly during power-up, power-down, or bus contention. The SN74HC125N has no three-state input; unused data inputs should be tied to a defined valid logic level rather than left floating.
コンプライアンス情報
The SN74HC125N is a general-purpose logic IC rather than an automotive-qualified device. Specific environmental and material compliance declarations should be confirmed against the current manufacturer product documentation.