SN74LS697N - 4-Bit Synchronous Up/Down Counter | Texas Instruments
部品番号: SN74LS697N ✓ 生産中SN74LS697N 概要
A synchronous binary counter is a sequential logic device whose internal state changes in step with an active clock edge. The SN74LS697 belongs to the broader 74LS TTL logic family and combines a counter element with parallel output registers. Its up/down control permits operation as an incrementing counter, decrementing counter, or programmable frequency-divider stage. The output-register stage separates the counting sequence from the signals presented at the multiplexed outputs.
The principal features include one 4-bit counting element, a positive-edge clock input, directional counting control, registered outputs, and three-state output capability. The three-state outputs allow multiple counters or other bus-driving devices to share a common data bus when output-enable control is active. This combination is useful in systems requiring orderly bus access, event sequencing, or synchronized transfer of counter values.
The SN74LS697N is a member of the SN74LS logic series and uses the SN74LS697 function designation. Its registered outputs provide a defined output state between active clock events, while the synchronous counting architecture simplifies designs where multiple counting stages must update in step. When cascading devices, the carry output can be used to extend counting range and coordinate event boundaries.
Typical applications include frequency division, pulse and event counting, programmable timing modules, digital test equipment, industrial sequence controllers, and bus-oriented digital subsystems. The device can also serve as the central counting element in measurement systems that must divide an input frequency, count fixed-duration events, or present a latched hexadecimal or binary count to a host processor.
Designers should use the pin-description table in the Texas Instruments SN74LS697 datasheet when assigning PCB signals, especially for output-enable and directional-control pins. Because the outputs are multiplexed and three-state capable, the system must keep output-enable and bus-control timing separate from the clock edge requirements. Unused inputs should be held at a defined logic level according to the datasheet guidance.
This page combines the Texas Instruments function description, package information, application guidance, sourcing questions, and replacement constraints into a practical engineering reference for the SN74LS697N. It also distinguishes a verified function-compatible ordering suffix from a genuine cross-manufacturer drop-in equivalent, helping designers avoid assuming that similar counter ICs are pin-compatible without reviewing their datasheets.
ドロップイン代替品: SN74LS697N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストSN74LS697N 最大定格&電気的特性
| Logic Type | Synchronous 4-bit binary up/down counter |
| Counting Element | 1 counter element |
| Counter Width | 4 bits |
| Clock Edge | Positive edge |
| Output Features | Registered outputs with multiplexed three-state outputs |
| パッケージ | PDIP-20 |
| ピン数 | 20 pins |
| 動作温度範囲 | 0°C to 70°C |
| Logic Family | SN74LS |
| 実装タイプ | Through-hole |
SN74LS697N pdip-20 ピン配置ガイド
SN74LS697N (pdip-20 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: SN74LS697N.
詳細は データシート をご参照ください。
主な用途
SN74LS697N の用途: 6 件s: Frequency Divider, Event and Pulse Counting, Programmable Timing Module, Digital Test Equipment, Industrial Sequence Control, Bus-Controlled Counter Interface.
Frequency Divider
The SN74LS697N is well suited to programmable frequency division because it combines a 4-bit synchronous counter with a registered output stage and a carry output for cascading. A fixed count interval can be selected through the counter controls, while the active-edge clocking keeps the count state predictable relative to the input waveform. Its three-state outputs are useful when the divided signal must be routed onto a shared bus without permanent driver contention. Designers should set the direction and enable levels according to the Texas Instruments SN74LS697 datasheet and verify timing margins at the intended input frequency.
おすすめ
Event and Pulse Counting
The SN74LS697N can count discrete events arriving as a clock signal and retain the resulting count for later processing. Its 4-bit count capacity covers 0 through 15 states, while the carry output provides a natural boundary indication or a means to cascade another stage for a larger range. Registered outputs add a defined sampling point to the interface logic. For accurate pulse counting, the source must meet the clock setup and hold requirements stated in the Texas Instruments SN74LS697 datasheet, and the counter must remain enabled during the complete event sequence.
おすすめ
Programmable Timing Module
The SN74LS697N provides the counting and output-storage functions required for a programmable timing module. The external clock establishes the time base, the up/down control selects the counting direction, and the registered outputs hold a stable count value for downstream control logic. The carry output can mark rollover or drive an additional counting stage when a longer interval is needed. Because this is a synchronous design, clock-edge behavior and input timing are central to accurate timing; engineers should review the timing diagrams and output-control sequences in the Texas Instruments SN74LS697 datasheet.
おすすめ
Digital Test Equipment
The SN74LS697N can act as a programmable sequence and count element in digital test equipment where repeated input pulses must be divided, counted, and made available to a control section. Its three-state multiplexed outputs allow the instrument bus to share the counter outputs with other peripheral devices under coordinated output-enable control. The registered outputs provide a stable interface value between clock events. Test-system designers should account for propagation delay, clock tolerance, and bus contention margins using the timing information in the Texas Instruments SN74LS697 datasheet.
おすすめ
Industrial Sequence Control
The SN74LS697N fits industrial sequence-control tasks that require repeatable counting, directional operation, and a latched count output. A controller can use the count to select a machine step, trigger an actuator sequence, or divide a production-cycle pulse train. The 0°C to 70°C operating range covers commercial and industrial environments where appropriate enclosure temperature control is maintained. Designers should define all control inputs during reset and power transitions, and use the manufacturer's input-level and timing requirements to prevent unintended count increments.
おすすめ
Bus-Controlled Counter Interface
The SN74LS697N supports bus-oriented counter interfaces because its outputs are registered and can be placed in a high-impedance state. A host or system controller can enable the counter outputs at a defined bus interval and read the current 4-bit value without tying the data bus continuously to the device. The design must ensure that enable and disable timing does not overlap with another bus driver. Because the SN74LS697N combines counting and multiplexing, engineers should validate both the counter-clock timing and bus ownership sequence using the Texas Instruments SN74LS697 datasheet.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74LS697N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Texas Instruments |
| Package | PDIP-20 |
| Function | Synchronous 4-bit up/down binary counter |
| Counter Elements | 1 |
| Counting Width | 4 bits |
| Clock Edge | Positive edge |
| Output Architecture | Registered outputs with multiplexed three-state outputs |
| Operating Temperature | 0°C to 70°C |
| Mounting Type | Through-hole |
| Logic Family | SN74LS |
主な差別化要因
- Counter and registered-output functions are combined in one device (vs SN74LS593N)
- Directional counting is built into the counter element (vs SN74LS181N)
- Output-register stage supports controlled bus sharing (vs SN74LS593N)
設計ノート
Treat the clock, direction, enable, and output-enable signals as synchronous control inputs. The direction and enable levels must be stable for the setup-and-hold interval specified in the Texas Instruments SN74LS697 datasheet. Avoid routing the clock directly beside multiplexed output signals when a clock transition could couple into an output during a bus-switching interval. Use a ground plane and short point-to-point clock traces to reduce susceptibility to noise-induced count errors.
Assign PCB connections from the manufacturer's 20-pin PDIP pin-description table rather than from a generic counter diagram. Keep the three-state output paths away from clock and control traces, and maintain a continuous ground reference beneath the device where the board layout permits. Because several outputs are multiplexed, their physical order can affect routing efficiency; planning the bus direction before placing the IC reduces crossings and makes output-enable routing easier to inspect.
Do not enable the three-state outputs while another device drives the same bus. Confirm the output-enable polarity and required setup timing from the Texas Instruments SN74LS697 datasheet, and do not assume that a high-impedance output preserves the previous data level at the receiver. Also avoid changing the counting direction close to a clock edge, because setup-and-hold violations can cause an incorrect count state even though the circuit appears static when troubleshooting.
コンプライアンス情報
The device is a commercial-temperature 0°C to 70°C logic IC; automotive qualification is not indicated. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses require confirmation from the current manufacturer documentation.