Texas Instruments

SN75185N - 3/5 RS-232 Transceiver, 120 kbit/s | Texas Instruments

部品番号: SN75185N ✓ 生産中
TIA/EIA-232-F, ITU V.28 Rds(on) PDIP-20 (20-pin plastic dual in-line) Package
MOQ: 1 |

SN75185N 概要

The Texas Instruments SN75185N is a single-chip RS-232 interface integrated circuit that combines three line drivers and five line receivers, supporting data rates up to 120 kbit/s in a 20-pin plastic DIP (PDIP-20) package. It meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 standards for unbalanced serial interfaces and provides ESD protection of 10 kV on the RS-232 pins and 3.5 kV on all other pins under the Human-Body Model.

An RS-232 transceiver is a signal-conditioning device that converts logic-level TTL/CMOS signals into the differential voltage levels defined by the RS-232 standard, and converts returning RS-232 levels back into logic levels for the host controller. In the interface hierarchy, the SN75185N sits at the physical-layer boundary between a UART transmitter/receiver inside a microprocessor and the physical DB9 or DB25 serial connector of an IBM PC/AT-class or compatible host.

Key features include the asymmetric channel count of three drivers and five receivers, which allows one UART port to share several receive lines or monitor several inputs. The flow-through pinout matches the SN75C185, making board-level interchanges straightforward, and the bipolar process provides the drive current and slew characteristics expected from legacy PC serial ports. Operating voltage is the standard 5 V class, and the device is offered in a through-hole plastic DIP suited to legacy industrial and instrumentation chassis.

Technically, the SN75185N integrates multiple SN75188-style bipolar drivers and SN75189-style receivers on one die. Because the receivers are of the threshold type with internal hysteresis, noise immunity at the connector side is high, while the drivers provide the ±5 V to ±15 V swing that RS-232 requires. Data rates of up to 120 kbit/s are adequate for legacy UART traffic, and the combination of three drivers lets a single port support transmit plus two additional output signals such as DTR and RTS if the host software drives them directly.

Typical applications include legacy PC/AT serial port interfaces, industrial control panels with DB9 connectors, laboratory and test instrumentation with legacy serial console ports, embedded boards that must talk to older supervisory software, and multi-drop or monitoring arrangements where several status lines are read back from one port.

A key design consideration is that the SN75185N is a legacy bipolar part intended for 5 V single-supply operation and through-hole assembly; it is not a modern 3.3 V tolerant design, and it should not be substituted into RS-232 channels running at 3.3 V logic without a level shifter. Plan PCB real estate for a 20-pin DIP footprint if the goal is a drop-in repair of an existing board rather than a new design.

This page brings together the manufacturer interface standards, ESD ratings, channel configuration, pin-compatibility notes, and drop-in alternatives for the SN75185N, plus practical design and sourcing guidance that is not consolidated in a single place on the manufacturer datasheet.

ドロップイン代替品: SN75185N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

SN75C185N

✅ ドロップイン
📦 PDIP-20 (20-pin plastic dual in-line)
CMOS implementation of the same flow-through pinout versus the bipolar SN75185N; same 20-pin DIP footprint, same 3/5 channel configuration and 120 kbit/s class, with lower supply current but different drive characteristics

📋 参考代替品(カタログ未掲載)

SN75185

✅ ドロップイン
📦 PDIP-20 (20-pin plastic dual in-line)
Same silicon and same 20-pin PDIP footprint as the SN75185N; differs only in ordering code granularity, with no electrical or pin difference

📋 参考代替品(カタログ未掲載)

SN75C185

✅ ドロップイン
📦 PDIP-20 (20-pin plastic dual in-line)
CMOS base ordering code for the pin-to-pin-compatible SN75C185; same 20-pin DIP footprint and flow-through pinout versus the bipolar SN75185N, with different supply current and output slew

📋 参考代替品(カタログ未掲載)

SN75185N 仕様

Device Type RS-232 transceiver (3 drivers / 5 receivers)
Number of Drivers 3
Number of Receivers 5
Maximum Data Rate 120 kbit/s
Standards Compliance TIA/EIA-232-F, ITU V.28
ESD Protection on RS-232 Pins 10 kV (Human-Body Model)
ESD Protection on All Other Pins 3.5 kV (Human-Body Model)
Package Type PDIP-20 (20-pin plastic dual in-line)
ピン数 20
実装タイプ Through-hole
Process Technology Bipolar

SN75185N pdip-20 (20-pin plastic dual in-line) ピン配置ガイド

SN75185N (pdip-20 (20-pin plastic dual in-line) パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

SN75185N の pdip-20 (20-pin plastic dual in-line) パッケージピン配置図

詳細なピン配置データはありません: SN75185N.

詳細は データシート をご参照ください。

主な用途

SN75185N の用途: 6 件s: Legacy PC/AT Serial Port Interface, Industrial Control Panel DB9 Connectivity, Laboratory and Test Instrumentation Console, Multi-Channel Status Monitoring, Embedded Equipment Retrofit and Repair, Point-of-Sale and Peripheral Connectivity.

💻

Legacy PC/AT Serial Port Interface

The SN75185N was designed for the UART-to-DB9 interface of IBM PC/AT and compatible hosts, and it remains the natural choice for restoring or cloning a legacy serial port. Three drivers cover TXD, RTS and DTR, while five receivers bring back CTS, DSR, DCD, RI and the loopback/data status lines from the connector. With support to 120 kbit/s, the part spans 9600 bit/s console links through 115200 bit/s traffic, and the 10 kV HBM ESD rating on the RS-232 pins protects the connector side during routine cabling and servicing.

🏭

Industrial Control Panel DB9 Connectivity

Machinery and process-control panels frequently keep RS-232 connectors long after the surrounding electronics moved to Ethernet, and the SN75185N bridges a modern UART core to that connector in a single IC. Driving three outputs and reading five inputs in one 20-pin DIP reduces board area compared with separate driver and receiver pairs, which matters in crowded control cabinets. The bipolar circuits sustain the slew and drive current that long shielded cables demand, while the flow-through pinout keeps traces short between the transceiver and the DB9 header.

🔧

Laboratory and Test Instrumentation Console

Bench instruments, programmers and analyzers still expose RS-232 service consoles, and the SN75185N provides a compact way to add that port alongside USB and Ethernet interfaces. The five receivers allow the instrument to read back handshake and status signals so supervisory software can confirm that a command was accepted, and the three drivers let the host toggle RTS or DTR for hardware handshaking on slower links. At 120 kbit/s the interface is fast enough for firmware upload sessions and log transfers without adding meaningful delay to a test cycle.

📡

Multi-Channel Status Monitoring

Where a single serial port has to supervise several remote devices, the asymmetric 3/5 channel count of the SN75185N lets one port handle both a data channel and several discrete status or interlock lines. Three drivers can drive request or select signals to multiple targets while five receivers monitor ready, fault and acknowledge inputs coming back from them. This arrangement replaces several separate single-channel RS-232 devices, and the 3.5 kV HBM rating on the non-RS-232 logic pins protects the host-side inputs that are tied to system logic.

🛠️

Embedded Equipment Retrofit and Repair

The SN75185N through-hole PDIP-20 package makes it a natural part for repairing or retrofiting older embedded equipment where the board originally used a socketed 20-pin transceiver. Because the flow-through pinout matches the SN75C185, boards can be respun or hand-patched with either the bipolar or CMOS variant without respinning the copper. The 10 kV HBM ESD rating on the RS-232 pins is particularly valuable in retrofit work, where the connector is often routed through poorly shielded harnesses in the field.

🖥️

Point-of-Sale and Peripheral Connectivity

Receipt printers, weigh scales, card readers and barcode scanners in the point-of-sale channel still use RS-232 for command and status exchange, and the SN75185N provides the physical layer in a single small DIP package. The three drivers support data plus printer handshakes, while the five receivers read paper-out, error and busy indications so the host can queue transactions correctly. Because the transceiver is a through-hole part, it fits the large-hole, long-lifetime PCBs typical of commercial POS equipment built for serviceability.

What is the SN75185N and what does it do?
The SN75185N is a Texas Instruments single-chip RS-232 interface IC that combines three line drivers and five line receivers in one 20-pin plastic DIP package. According to the TI SN75185 product page, it meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 standards and supports data rates up to 120 kbit/s, providing a single IC interface between a UART and the DB9 or DB25 serial connector of an IBM PC/AT-class host.
How many drivers and receivers does the SN75185N have?
The SN75185N contains three drivers and five receivers. According to the Texas Instruments SN75185 product description, the part combines three drivers and five receivers drawn from the SN75188 and SN75189 bipolar driver/receiver families onto a single die. The 3/5 asymmetry lets one UART port transmit data while reading back up to five modem-control or status lines.
What is the maximum data rate of the SN75185N?
The SN75185N supports data rates up to 120 kbit/s. The manufacturer datasheet revision D for the SN75185 family lists support for data rates to 120 kbit/s, which comfortably covers legacy UART traffic of 9600, 19200, 38400, 57600 and 115200 bit/s used by PC/AT serial ports and industrial console links.
Which RS-232 standards does the SN75185N meet?
The SN75185N meets or exceeds the requirements of TIA/EIA-232-F and the ITU V.28 standard, as stated on the Texas Instruments SN75185 product page. V.28 defines the electrical characteristics of the unbalanced 200 baud modem interface commonly used for serial console links, while TIA/EIA-232-F is the modern revision of the RS-232 standard.
What ESD protection does the SN75185N provide?
The SN75185N provides ESD protection that meets or exceeds 10 kV on the RS-232 pins and 3.5 kV on all other pins under the Human-Body Model. According to the Texas Instruments SN75185 product features, the connector-side pins carry the highest rating because they are the pins most likely to be touched during cabling and servicing.
Is the SN75185N pin-compatible with the SN75C185?
Yes. The Texas Instruments SN75185 product page states that the SN75185 pinout matches the flow-through design of the SN75C185, and the feature list explicitly calls out pin-to-pin compatibility with the SN75C185. This makes the SN75185N a convenient upgrade path when a bipolar driver is preferred over CMOS implementations, provided the supply voltage requirement is met.
What package does the SN75185N come in?
The SN75185N is supplied in a 20-pin plastic dual in-line package, designated PDIP-20, and is intended for through-hole PCB assembly. The DigiKey listing for SN75185N identifies it as a 3/5 RS-232 transceiver in a 20-PDIP package. Because it is a through-hole part, it is normally used for board repair or legacy chassis designs rather than new high-density surface-mount boards.
Where can I download the SN75185N datasheet PDF?
The SN75185 datasheet revision D is available from the Texas Instruments product page at https://www.ti.com/product/SN75185, where it is listed under technical documentation as the SN75185 datasheet. Archived HTML copies of the same document are also hosted on alldatasheet.com under part number SN75185N. The TI document describes the driver and receiver electrical characteristics, pin assignments and typical applications.
Where do I find the SN75185N pinout?
The authoritative pin assignments for the SN75185 are in the Texas Instruments SN75185 datasheet revision D, in the pin configuration table, and the same information is reproduced on the TI SN75185N part-details page. Because the SN75185N uses a flow-through pinout shared with the SN75C185, cross-checking the SN75C185 pin diagram against your board is a quick way to confirm orientation before soldering.
What can replace the SN75185N?
The closest drop-in replacement is the SN75C185N, a CMOS RS-232 transceiver in the same 20-pin DIP with a pin-to-pin-compatible flow-through arrangement. The SN75185 base device in PDIP is an identical ordering option, and the SN75C185 in PDIP is the CMOS counterpart. Note that the MC1489N frequently seen in cross-reference listings is a 14-pin quad receiver, so it is not a footprint-compatible substitute.
What is the best equivalent for the SN75185N from another manufacturer?
No equivalent from another manufacturer is confirmed as a true drop-in for the SN75185N. The MC1489N and MC1488N that surface in cross-reference tables differ in both channel count and package, with the MC1489N offered in a 14-pin DIP and the MC1488N as a separate driver pair. The only pin-compatible 20-pin DIP option with a documented match is the Texas Instruments SN75C185N.
SN75185N vs SN75C185N - which should I choose?
Choose the SN75185N when you specifically need bipolar drive characteristics and the legacy PC/AT interface heritage, and choose the SN75C185N when a CMOS implementation with lower supply current suits the design better. Both share the same 20-pin DIP flow-through footprint and 120 kbit/s class of operation, so the decision is usually driven by supply-voltage compatibility with the surrounding logic and by drive-current expectations on long cables.
When should I choose the SN75185N over the SN75C185N?
Select the SN75185N when your system already contains legacy bipolar logic or when you need the driver behaviour the SN75188 and SN75189 families are known for, particularly on long or noisy cables. Select the SN75C185N for new designs where supply current, CMOS supply-voltage tolerance and cost dominate. Because the packages are identical, both can occupy the same board revision with a change in the bill of materials.
Is the SN75185N suitable for industrial RS-232 equipment?
The SN75185N is well suited to industrial equipment that must retain legacy RS-232 console ports, because it offers 10 kV HBM ESD protection on the RS-232 pins, three drivers for data plus handshake outputs, and five receivers for reading modem-control status lines. For new designs with 3.3 V system logic, verify the supply-voltage requirement in the datasheet and consider a level shifter or a modern 3.3 V transceiver instead.
How do I order the SN75185N and what is the lead time?
The SN75185N is available from Texas Instruments as an active catalog part with a standard 20-pin PDIP ordering code, listed on the TI SN75185 part-details page and stocked through authorized distributors. Current lead time, minimum order quantity and per-piece pricing for this exact suffix are best confirmed through the Request a Quote form on this page, which returns current factory and channel availability.
What is the price of the SN75185N and is it in stock?
Pricing and stock for the SN75185N move with the channel and the quantity break, so the current figure is best obtained through the Request a Quote form on this page rather than from a static table. The part is a long-running catalog item of Texas Instruments, and the SN75185 product line remains supported, which generally means supply is stable for the 20-pin PDIP configuration.
What are the key specifications of the SN75185N that engineers should know?
The SN75185N is a 3-driver, 5-receiver RS-232 transceiver rated to 120 kbit/s, meeting TIA/EIA-232-F and ITU V.28, with 10 kV HBM ESD protection on the RS-232 pins and 3.5 kV on all other pins. It uses a flow-through pinout shared with the SN75C185 and is built on bipolar technology, all in a 20-pin plastic DIP through-hole package for legacy PC/AT serial interfaces.

エンジニアリング参考データ: SN75185N — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the SN75185N when you are restoring, cloning or extending a legacy PC/AT-class RS-232 port that needs three outbound lines and five inbound lines on a 5 V supply, especially when the board already has a 20-pin through-hole footprint. Choose the SN75C185N when the same board needs a CMOS implementation for lower supply current or better tolerance of modern supply rails, since the manufacturer states the two are pin-to-pin compatible. Choose the SN75185 base ordering code when you need the identical silicon in PDIP without the N suffix. If your only need is reading status lines, a dedicated quad receiver such as the MC1489N is simpler but it is a 14-pin part and cannot drive the transmit and handshake outputs, so it is not a footprint substitute. For new 3.3 V designs, prefer a modern transceiver instead of this bipolar part.

代替品との比較

パラメータ この製品 SN75C185N SN75185 SN75C185
Package PDIP-20 (20-pin plastic dual in-line) PDIP-20 - same footprint PDIP-20 - same footprint PDIP-20 - same footprint
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Device Type 3 drivers / 5 receivers RS-232 transceiver RS-232 transceiver, flow-through pinout 3 drivers / 5 receivers RS-232 transceiver RS-232 transceiver, flow-through pinout
Process Technology Bipolar CMOS Bipolar CMOS
Standards Compliance TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28
Pin Compatibility Flow-through pinout, pin-to-pin compatible with SN75C185 Pin-to-pin compatible with SN75185 Same pinout as SN75185N Pin-to-pin compatible with SN75185

主な差別化要因

  • Three drivers and five receivers consolidated in a single 20-pin DIP instead of separate driver and receiver ICs (vs MC1488NE4)
  • Pin-to-pin flow-through layout allows one PCB to accept both bipolar and CMOS implementations (vs SN75C185N)
  • Connector-side ESD rating of 10 kV HBM covers the pins most exposed during cabling (vs MC1489NG4)

設計ノート

Do not treat the SN75185N as a 3.3 V tolerant device. It is a bipolar 5 V class part, and although the receiver thresholds are referenced to the supply rail, the supply voltage and the host-side logic levels must be checked in the datasheet before connecting a 3.3 V UART. If the surrounding controller runs at 3.3 V, use a bidirectional level shifter on TXD and the handshake inputs, or choose a modern 3.3 V-capable RS-232 transceiver instead of forcing the SN75185N onto the rail.

The SN75185N uses a flow-through pinout specifically so that traces run straight from the host logic to the DB9 connector without crossing. Keep the connector-side nets short, keep the ground and chassis-shield return path adjacent to the signal pairs, and place any protection network at the connector rather than at the IC. Because the flow-through arrangement mirrors the SN75C185, you can lay out once and populate either part, which makes it easy to qualify a CMOS version on the same board revision.

The RS-232 driver outputs are large-swing signals and the receiver inputs are high-impedance, so both are sensitive to coupling from adjacent switching nodes. Route the five receiver inputs away from clock, motor and relay traces, keep the ribbon-cable interface short and prefer a shielded cable with the shield tied to chassis ground at the connector. Estimated note: with three drivers simultaneously switching at 120 kbit/s, expect the highest EMI when all three outputs change state together, so stagger data and handshake toggling in firmware where the protocol allows.

Although the device is a 5 V part, the RS-232 driver outputs swing above and below the supply rails to meet the TIA/EIA-232-F voltage levels, and the supply decoupling must be sized for the driver current pulses. Place a 0.1 uF ceramic capacitor plus a bulk electrolytic or 1 uF to 10 uF ceramic close to the supply pins, and verify the maximum total supply current in the datasheet against the worst case where all three drivers switch simultaneously.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The SN75185N is a legacy bipolar through-hole RS-232 transceiver and is not an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free and halogen-free statements were not present in the retrieved pages and must be confirmed on the Texas Instruments SN75185 product page or via a current material declaration before use in restricted applications.

データ検証日: 2026-11-09 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

SN75185N datasheet SN75185N pinout SN75185N datasheet pdf SN75185N 20 pin dip pinout SN75185N replacement SN75185N equivalent transceiver SN75185N vs SN75C185N SN75185N RS-232 120 kbit/s Texas Instruments SN75185N SN75185N price and stock SN75185N buy online RS-232 3 driver 5 receiver IC SN75185 flow-through pin layout SN75185 lead time

関連部品&用語

Texas Instruments SN75185N SN75185 SN75C185N SN75188 SN75189 RS-232 transceiver line driver line receiver physical layer interface IC interface IC semiconductor TIA/EIA-232-F ITU V.28 ESD protection Human-Body Model PDIP-20 dual in-line package through-hole flow-through pinout UART DB9 serial connector IBM PC/AT bipolar CMOS
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示