STM32F042F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
部品番号: STM32F042F4P6 ✓ 生産中STM32F042F4P6 概要
A microcontroller is an integrated semiconductor containing a processor core, memory, and peripherals on one chip. The STM32F0 MCU family belongs to the embedded-processing hierarchy: microcontroller → 32-bit RISC MCU → ARM Cortex-M0 microcontroller → embedded-control device. Its combination of 48 MHz processing speed, USB connectivity, and a 20-pin package makes it useful for USB-connected control, industrial interface, and compact consumer products.
Key features include a 32-bit ARM Cortex-M0 core, 48 MHz maximum operating frequency, and 16 KB of Flash for firmware storage. The device also provides 6 KB of SRAM and integrated USB, CAN, and CEC functions. Its 2.4 V to 3.6 V operating-supply range suits 3.3 V systems, while the 20-TSSOP package supports compact, high-density PCB layouts. These characteristics balance processing performance and interface coverage without requiring a larger pin count.
The STM32F0 architecture is based on a 32-bit reduced-instruction-set-computing core intended for efficient embedded control. Flash-resident code and SRAM support boot-time firmware, event handling, communication stacks, and peripheral control, while USB and CAN provide paths for connected equipment and industrial networking. The USB and CAN interfaces distinguish this device from basic Cortex-M0 microcontrollers that support only serial or general-purpose interfaces.
Typical applications include USB human-interface-interface accessories, compact industrial controllers, CAN-connected sensors, consumer electronics, and battery-operated equipment. The MCU can also manage LED interfaces, communication bridges, and low-speed embedded control tasks where board area is constrained. Its 20-pin package and 3.3 V supply architecture simplify integration into compact USB dongles, control modules, and secondary embedded processors.
Designers should reserve all 20 TSSOP positions, route the USB data and power pins according to the manufacturer reference design, and confirm firmware support for the selected USB, CAN, and CEC peripheral configuration before PCB release. The 16 KB Flash limit requires attention to bootloader size, protocol libraries, and application code. For a production migration, verify pin multiplexing, clock setup, peripheral mapping, and interrupt behavior against the manufacturer datasheet.
This page combines the official STM32F042F4 product information, exact-order-code listings, interface and memory details, same-brand drop-in alternatives, and practical integration guidance. It is intended to accelerate part selection, schematic review, firmware planning, and footprint verification for engineers designing with the STM32F042F4P6.
ドロップイン代替品: STM32F042F4P6 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STM32F042F4P6 (同一形状・フットプリント) — 相違点: Flash Memory, Product Type, Package, SRAM, ADC Resolution.
STM32F042F6P6
✅ ドロップイン価格はお問い合わせください
データシートを見る →STM32F042F4P7
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
STM32F070F4P6
✅ ドロップイン📋 参考代替品(カタログ未掲載)
STM32F070F6P6
✅ ドロップイン価格はお問い合わせください
データシートを見る →STM32F030F4P6
✅ ドロップイン価格はお問い合わせください
データシートを見る →STM32F042F4P6 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Core | ARM Cortex-M0 |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 6 KB |
| 動作電源電圧 | 2.4 V to 3.6 V |
| 動作温度 | -40 °C to +85 °C |
| USB Interface | Yes, USB device line |
| CAN Interface | Yes |
| CEC Interface | Yes |
| ADC Resolution | 12-bit |
| パッケージ | 20-pin TSSOP |
| Package Width | 4.40 mm |
| 実装タイプ | Surface mount |
| Packing Type | Tube |
| RoHS ステータス | Compliant |
| Program Memory Type | Flash |
| Bit Width | 32-bit |
| Peripheral Pin Count | 20 pins |
| ECN | US-3A991.a.2 |
STM32F042F4P6 4.40 mm ピン配置ガイド
STM32F042F4P6 (4.40 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: STM32F042F4P6.
詳細は データシート をご参照ください。
主な用途
STM32F042F4P6 の用途: 6 件s: USB Human-Interface Devices, CAN-Connected Industrial Control, Consumer Interface and Control Module, Battery-Powered Embedded Sensor Node, CEC-Connected Consumer Electronics, LED and Compact Automation Controller.
USB Human-Interface Devices
The STM32F042F4P6 fits USB keyboards, mice, game controllers, and configuration adapters because its 48 MHz Cortex-M0 core can service USB traffic while the device includes dedicated USB, CAN, and CEC connectivity. The 16 KB Flash provides a constrained environment for a boot program, USB class code, and device logic, while 6 KB of SRAM supports packet handling and control state. Its 20-pin TSSOP package reduces board footprint in compact USB accessories. The principal design consideration is firmware capacity: USB middleware, descriptors, and application behavior must be selected and measured against the 16 KB limit before layout release.
おすすめ
CAN-Connected Industrial Control
The STM32F042F4P6 is appropriate for compact CAN-connected controllers because it combines a CAN interface with a 48 MHz ARM Cortex-M0 core and 16 KB of Flash. It can handle sensor polling, state-machine control, diagnostic reporting, and communication framing within a 4.40 mm-wide 20-pin TSSOP footprint. The 2.4 V to 3.6 V operating range aligns with 3.3 V industrial circuitry. Designers should allocate flash space carefully, confirm the exact peripheral and pin assignments, and validate bus timing, termination, isolation, and EMC requirements against the final CAN transceiver and system topology.
おすすめ
Consumer Interface and Control Module
The STM32F042F4P6 can serve as the controller in a compact consumer interface module that needs USB connectivity, embedded logic, and modest local memory. Its 48 MHz Cortex-M0 core provides adequate performance for button handling, indicator control, status reporting, and communication with a host device. The 20-pin TSSOP package is useful where product volume and board area are tightly constrained, while the 16 KB Flash and 6 KB SRAM are sufficient for focused, optimized firmware. Product developers should reserve programming and debug access, avoid unnecessary middleware, and verify start-up behavior across the complete USB power and brownout sequence.
おすすめ
Battery-Powered Embedded Sensor Node
The STM32F042F4P6 is useful in a battery-powered sensor node when low-voltage operation, local processing, and compact packaging are priorities. The listed 2.4 V to 3.6 V supply range supports regulated 3.3 V sensor systems, and the 16 KB Flash can hold tightly scoped acquisition and control routines. Its 48 MHz Cortex-M0 core permits responsive sampling and event processing without a larger package. Battery design remains dominated by regulator efficiency, quiescent load, and sensor duty cycle, so developers should minimize USB activity and use the MCU's low-power modes only after validating wake timing, retention, and peripheral reinitialization.
おすすめ
CEC-Connected Consumer Electronics
The STM32F042F4P6 fits compact consumer products that need CEC control alongside general embedded processing. The MCU's 48 MHz Cortex-M0 core and 6 KB of SRAM are sufficient for command handling, device-state management, and simple user-interface coordination, while the 20-pin TSSOP package supports board-area reduction. The 16 KB Flash limit encourages a compact protocol implementation and disciplined driver selection. Before schematic release, engineers should confirm the exact CEC pin mapping, electrical levels, pull requirements, and interaction with the product's power-management and infrared or physical bus implementation.
おすすめ
LED and Compact Automation Controller
The STM32F042F4P6 can act as a compact controller for LED fixtures, status indicators, or small automation products. Its 48 MHz core supports deterministic timer-based dimming, sequencing, button input, and communication updates, while the TSSOP-20 package leaves more board area for power components and connectors. The integrated USB interface can simplify configuration or service access in production and diagnostic setups. Firmware developers should calculate timer and DMA requirements within the STM32F042 peripheral set, budget the 16 KB Flash for lighting algorithms, and confirm that the selected pin multiplexing does not conflict with USB, CAN, or other assigned functions.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STM32F042F4P6 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | STM32F042F6P6 | STM32F042F4P7 | STM32F070F4P6 | STM32F070F6P6 | STM32F030F4P6 |
|---|---|---|---|---|---|---|
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 32 KB | 16 KB | 16 KB | 32 KB | 16 KB |
主な差別化要因
- Combines USB, CAN, and CEC in the same STM32F042 USB-line family (vs STM32F030F4P6)
- Lower Flash demand supports focused embedded firmware (vs STM32F042F6P6)
- Retains the same 20-TSSOP placement while offering a different memory balance (vs STM32F070F6P6)
設計ノート
Reserve the complete 20-pin TSSOP footprint and follow the manufacturer package drawing for pad dimensions, lead pitch, solder-mask clearance, and exposed pad requirements. Place all decoupling capacitors close to their associated power pins, with a short and low-impedance ground return. Because this is a mixed-signal communication MCU, route USB data as a short, continuous pair away from switching nodes and provide the required USB routing geometry on the board stack-up.
Do not assume that a 20-TSSOP footprint match guarantees a functional drop-in migration. The STM32F042, STM32F070, and STM32F030 families can differ in peripheral availability, alternate-function mappings, interrupt vectors, clock trees, and firmware support. Build a pin-by-pin comparison against the exact alternative datasheet, then recompile and test the application, USB enumeration, CAN communication, boot flow, and low-power transitions before releasing a revised PCB.
Design the supply for 2.4 V to 3.6 V operation and account for USB attachment, boot, and peripheral-load transients rather than checking only steady-state current. Keep the MCU supply within the manufacturer limits during startup, brownout recovery, and USB bus transitions. Place bulk and high-frequency bypass capacitance at the power entry and device pins, verify regulator startup against internal reset timing, and use the device's low-power modes only after measuring real peripheral and board-level standby current.
Keep programming and debug access available on the assembled PCB even if the product does not expose a user connector. Route SWDIO and SWCLK with short, clean traces and provide a controlled boot configuration path. Avoid assigning high-current outputs, relays, or inductive switching nodes to pins adjacent to sensitive communication or debug functions unless the package pin table confirms the intended multiplexing. Verify the 48 MHz clock source layout and decoupling strategy in the manufacturer reference design.
コンプライアンス情報
The exact-device comparison information identifies RoHS compliance and the industrial temperature grade. Other environmental and supply-chain declarations require confirmation for the specific order code.